77.150.30 铜产品 标准查询与下载

ASTM B694-19 电缆屏蔽用铜、铜合金、铜包青铜（CCB）、铜包不锈钢（CCS）和铜包合金钢（CAS）薄板和带材的标准规范

1.1 This specification establishes the requirements for copper, copper alloy, copper-clad bronze (CCB), copper-clad stainless steel (CCS), and copper-clad alloy steel (CAS) materials, sheet, and strip, in various thicknesses, for use as electrostatic or electromagnetic shielding for insulated power, control, instrumentation, and communication cables. NOTE 1—See Specification B736, for related standards for aluminumbased shielding materials. 1.2 The products covered are the following: Copper or Copper Alloy UNS No. Type of Products C11000 copper C19400 copper-iron alloy C22000 copper-zinc alloy (commercial bronze) C23000 copper-zinc alloy (red brass) C66400 copper-zinc-iron-cobalt alloy C66410 copper-zinc-iron alloy C66430 copper-zinc-iron-tin alloy C71000 cupro-nickel 20 % ... copper-clad bronze (CCB) ... copper-clad stainless steel (CCS) ... copper-clad alloy steel (CAS) 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 The only exception is grain size, which is reported in SI (mm) units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding

ASTM B432-19 铜和铜合金复合钢板的标准规范

1.1 This specification establishes the requirements for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of copper or copper-base alloy. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance or conductivity of the alloy is of prime importance. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper and Copper Alloy Clad Steel Plate

ASTM B453/B453M-19 铜锌铅合金（铅黄铜）杆、棒和型材的标准规范

1.1 This specification establishes the requirements for copper-zinc-lead alloy (leaded-brass) rod, bar, wire, and shapes produced from Copper Alloys UNS Nos. C33500, C34000, C34500, C35000, C35300, C35330, C35350, and C35600. These alloys have nominal composition given in Table 1. 1.1.1 This product is suitable for applications requiring extensive machining before such cold-forming operations as swaging, flaring, severe knurling, or thread rolling. NOTE 1—Refer to Appendix X1 for additional applications information. 1.1.2 Typically, product made to this specification is furnished as straight lengths. Sizes 1⁄2 in. [12 mm] and under may be furnished as wire in coils or on reels when requested. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. NOTE 2—Refer to Specifications B16/B16M and B140/B140M for copper-zinc-lead (leaded-brass) rod and bar for screw machine applications. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes

ASTM B98/B98M-13(2019) 铜硅合金棒材和型材标准规范

1.1 This specification establishes requirements for coppersilicon rod, bar, and shapes for UNS Copper Alloys C65100, C65500, and C66100. NOTE 1—Material for hot forging is covered by Specification B124/ B124M. NOTE 2—For ASME Boiler and Pressure Vessel Code applications, see Specification SB-98 in Section II of that code. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes

ASTM B124/B124M-19 铜和铜合金锻造棒、棒和型材的标准规范

Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes

ASTM B411/B411M-14(2019) 铜镍硅合金棒

1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar

DIN SPEC 2701:2018-12 无铅铜合金 由 CuSn4Zn2PS 制成的铸锭和铸件

This DIN SPEC in accordance with the PAS procedure was developed within a workshop set up on a temporary basis. The DIN SPEC was developed and approved by the authors named in the foreword. This DIN SPEC specifies the composition, mechanical properties and other relevant characteristics of copper ingots and copper castings made of CuSn4Zn2PS. Other copper alloys are not part of this DIN SPEC and are described in EN 1982. For the applications of this document the information and requirements according to EN 1982 are applicable. This DIN SPEC applies to: a) copper alloy ingots made of CuSn4Zn2PS-B intended to be remelted for later processing (e. g. castings); and b) copper alloy castings made of CuSn4Zn2PS-C which are intended for use without subsequent working other than machining.

Unleaded copper alloys - Ingots and castings made of CuSn4Zn2PS; Text in German and English

ASTM B379-11(2018) 磷化铜标准规范&x2014；炼油厂形状

Standard Specification for Phosphorized Coppers—Refinery Shapes

YS/T 635-2018 卫生洁具用黄铜管

Brass tubes for sanitary ware

YS/T 649-2018 铜及铜合金挤制棒

本标准规定了铜及铜合金挤制棒的要求、试验方法、检验规则和标志、包装、运输、贮存及合同内容等。 本标准适用于一般用途的圆形、矩（方）形和六角形铜及铜合金挤制棒。

Extruded rod and bar of copper and copper alloys

YS/T 584-2018 电极材料用铬、锆铜棒材

Chromium and zirconium copper rods for electrode materials

T/ZZB 0637-2018 断路器用铜带

本标准规定断路器用铜带的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书、订货单（或合同）和质量承诺内容。 本标准适用于断路器用铜带（以下简称铜带）。

Copper strips for circuit breakers

ASTM B882-10(2018) 建筑用预镀铜的标准规范

1.1 This specification covers the establishment of the requirements for pre-patinated (artificially aged) copper sheet and strip in ounce-weight thicknesses supplied in flat lengths for roofing, flashing, and other architectural applications. 1.2 The pre-patinated surface is the result of chemical reaction with the copper and shall be applied on one side of the product. 1.2.1 The pre-patinated surface formed is comparable in color and ability to be bent or formed to the surface formed in naturally occurring patinated copper. 1.3 The pre-patinated surface is not the result of coating applications such as painting. 1.4 Materials made to this specification are not intended to be used for electrical applications. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—A companion specification for copper sheet and strip for building construction is Specification B370. 1.6 The following precautionary statement pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pre-Patinated Copper for Architectural Applications

ASTM B608-18 焊接铜合金管材标准规范

1.1 This specification establishes the requirements for arcwelded pipe for use in brackish water or seawater piping systems. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard statement pertains only to the test method described in 8.2 and 14.3.2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Copper-Alloy Pipe

ASTM B249/B249M-18a 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ASTM B950-18 铜和铜合金产品规范编辑程序和形式标准指南

Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys

ASTM B2-13(2018) 中硬拉铜线的标准规范

1.1 This specification covers medium-hard-drawn round copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception—For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Medium-Hard-Drawn Copper Wire

ASTM B21/B21M-18 海军黄铜杆、棒和型材的标准规范

Standard Specification for Naval Brass Rod, Bar, and Shapes

ASTM B171/B171M-18 压力容器、冷凝器和热交换器用铜合金板和薄板的标准规范

1.1 This specification2 establishes the requirements for copper-alloy plate, sheet, and circles cut from plate and sheet for pressure vessels, condensers, and heat exchangers. The following alloys are covered: Copper Alloy Previously Used Designation C36500 Leaded Muntz Metal C44300 Admirality, Arsenical C44400 Admirality, Antimonial C44500 Admirality, Phosphorized C46400 Naval Brass, Uninhibited C46500 Naval Brass, Arsenical C61300 Aluminum Bronze C61400 Aluminum Bronze D C63000 10 % Aluminum-Nickel Bronze C63200 9 % Aluminum-Nickel Bronze C70600 90-10 Copper Nickel C70620 90-10 Copper Nickel-(modified for welding) C71500 70-30 Copper Nickel C71520 70-30 Copper Nickel-(modified for welding) C72200 . . . 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers

ASTM B283/B283M-18a 铜和铜合金模锻件（热压）的标准规范

Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)