77.150.30 铜产品 标准查询与下载

ASTM B937-18 铜铍无缝管（UNS编号C17500和C17510）的标准规格

1.1 This specification establishes the requirements for copper-beryllium alloy seamless tube in straight lengths. Copper-cobalt-beryllium alloy UNS No. C17500 and coppernickel-beryllium alloy UNS No. C17510 will be the alloys furnished whenever this specification is specified. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Beryllium Seamless Tube (UNS Nos. C17500 and C17510)

ASTM B601-18 铜和铜合金回火名称的标准分类&x2014；锻铸

Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast

ASTM B21/B21M-18(2019) 船用黄铜条材、棒材和型材的标准规范

1.1 This specification establishes the requirements for naval brass rod, bar, and shapes produced from Copper Alloy UNS Nos. C46200, C46400, C46750, C47940, C48200, C48500, or C48640. 1.1.1 For piston-finish rod or shafting refer to the Other Requirements Section. 1.1.2 For hot forging material, refer to Specification B124/B124M. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.3 Warning—Mercury is a definite health hazard in use and disposal (see Performance Requirements). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Naval Brass Rod, Bar, and Shapes

ASTM B196/B196M-18 铜铍合金棒材标准规范

1.1 This specification establishes the requirements for copper-beryllium alloy rod and bar in straight lengths. The following three alloys are included: Copper Alloy UNS No. Previously Used Designations Nominal Beryllium Content, %       C17000 Alloy 165 1.7 C17200 Alloy 8199;25 1.9 C17300   1.9     +0.4 lead 1.2 Unless otherwise required, Copper Alloy UNS No. C17200 shall be the alloy furnished whenever Specification B196/B196M is specified without any alloy designation. 1.3 The values stated in either inch-pounds or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized p

Standard Specification for Copper-Beryllium Alloy Rod and Bar

ASTM B466/B466M-18 无缝铜镍合金管标准规范

1.1 This specification establishes the requirements for seamless copper-nickel pipe and tube in straight lengths, suitable for general engineering purposes. The alloys involved are copper alloys UNS Nos. C70400, C70600, C70620, C71000, C71500, C71520, and C72200. 1.1.1 Copper alloys UNS Nos. C70620 and C71520 are intended for product that will be subsequently welded. 1.2 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Copper-Nickel Pipe and Tube

ASTM B124/B124M-18 铜及铜合金锻造棒、棒和形状的标准规范

1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved: Copper UNS Nos. Copper Alloy UNS Nos. Copper Alloy EN 1412 Nos.         C11000 C27450 C49350 CW612N C14500 C27451 C49355 CW617N C14700 C27453 C49360     C28500 C61900     C35330 C62300     C36500 C63000  

Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes

ASTM B176-18 铜合金压铸件标准规范

1.1 This specification establishes the requirements for copper-alloy die castings. The alloys specified are Copper Alloy UNS Nos. C85470, C85700, C85800, C86500, C87800, C99700, and C99750.2 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Alloy Die Castings

T/ZZB 0273-2017 磁极线圈用铜型材

本标准规定磁极线圈用铜型材的基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存、订货单（或合同）和质量承诺等内容。 本标准适用于水轮发电机组磁极线圈用铜型材。

Copper profiles for pole coil

DIN EN 1982:2017-11 铜和铜合金.铸锭和铸件;德文版本EN 1982-2017

This European Standard specifies the composition, mechanical properties and other relevant characteristics of copper and copper alloys. The sampling procedures and test methods for the verification of conformity to the requirements of this standard are also specified. This standard is applicable to: a) copper alloy ingots intended to be remelted for later processing (e. g. castings); and b) copper and copper alloy castings which are intended for use without subsequent working other than machining. Recommended practice for the ordering and supply of castings as well as optional supplementary inspection procedures for ingots and castings are also included in the informative Annexes of this standard. NOTE Ingots are not suitable for pressure equipment applications.

Copper and copper alloys - Ingots and castings; German version EN 1982:2017

BS EN 1982:2017 铜及铜合金 铸锭和铸件

Copper and copper alloys. Ingots and castings

ASTM B283/B283M-17a 铜和铜合金模锻件（热压）的标准规范

Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

EN 1982:2017 铜和铜合金.金属块和铸件

Copper and copper alloys - Ingots and castings

YS/T 94-2017 硫酸铜（冶炼副产品）

本标准规定了硫酸铜(冶和帮副产品) 的要求.检验方法.检验规则、和包装、标志、运输、贮存和质量证 明书。 本标准适用于铜冶炼生产过程中副产出的结晶硫酸铜，产品主要用于电镀铜、电镀黄铜、化学镀铀、 工业催化剂和工业选矿等行业，不允许用于饲料.医药、食品添加剂和农用等行业。

Copper sulfate (smelting by-product)

ASTM B929-17 铜镍锡尖晶合金棒棒标准规格

1.1 This specification establishes the requirements for copper-nickel-tin alloy rod and bar. The following alloy is included: Copper Alloy UNS No. Nominal Composition, Weight % Copper Nickel Tin C72900 77 15 8 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Nickel-Tin Spinodal Alloy Rod and Bar

ASTM B176-17 铜合金压铸件的标准规范

1.1 This specification establishes the requirements for copper-alloy die castings. The alloys specified are Copper Alloy UNS Nos. C85470, C85700, C85800, C86500, C87800, C99700, and C99750.2 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Alloy Die Castings

ASTM B131-17 铜合金子弹夹克杯标准规格

15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value, or a calculated value, shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value     Chemical Composition Nearest unit in the last right-hand significant digit used in expressing the limiting value     Grain size Nearest multiple of 0.005 mm 1.1 This specification establishes the requirements for bullet jacket preform cups produced of Copper Alloy UNS No. C22000 for processing into bullet jackets of the following types and classes: 1.1.1 Type I—Caliber 0.30. 1.1.2 Type II—Caliber 0.45. 1.1.3 Type III—Caliber 0.50. 1.1.4 Type IV—As specified in the contract or order. 1.1.5 Class I—Not annealed. 1.1.6 Class II—Annealed. 1.2 Units—The values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of Internationa......

Standard Specification for Copper Alloy Bullet Jacket Cups

ASTM B824-17 铜合金铸件一般要求的标准规范

1.1 This specification establishes general requirements common to ASTM copper alloy casting specifications B22/B22M, B61, B62, B66, B67, B148, B176, B271/B271M, B369, B427, B505/B505M, B584, B763/B763M, B770, and B806. These requirements apply to the casting specifications to the extent referenced therein. 1.1.1 In the event of conflict between this specification and a casting specification, the requirements of the casting specification shall take precedence. 1.2 The chemical composition and other requirements not included in this specification shall be prescribed in the casting product specifications. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 No precise quantitative relationship can be stated between the properties of the metal in various locations of the same casting or between the properties of castings and those of a test bar casting from the same metal. (See Appendix X1.)2 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Copper Alloy Castings

ASTM B22/B22M-17 桥梁和转盘青铜铸件标准规范

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700. NOTE 1—Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B62-17 组成青铜或盎司金属铸件的标准规格

1.1 This specification2 establishes requirements for an alloy having a composition of copper, tin, lead, and zinc, used for component castings of valves, flanges, and fittings. The common trade name of this alloy is 85-5-5-5; the correct identification is Copper Alloy UNS No. C83600.3 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock from the manufacturer or other dealer. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Composition Bronze or Ounce Metal Castings

ASTM B422/B422M-17 铜铝硅钴合金, 铜镍硅镁合金, 铜镍硅合金, 铜镍铝镁合金和铜镍锡合金薄板和带材的标准规格

1.1 This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, C70310, and C70350 sheet and strip. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip