77.150.99 其他有色金属产品 标准查询与下载

YS/T 1498-2021 醋酸铑

Rhodium acetate

YS/T 1500-2021 多晶硅制备炉衬用银板材

Polycrystalline silicon prepares silver plate for furnace lining

YS/T 1492-2021 铂/二氧化钛

Platinum/Titanium Dioxide

YS/T 1471-2021 磷酸钒

Vanadium Phosphate

YS/T 1444-2021 镍钴钛三元素复合氢氧化物

Nickel-cobalt-titanium three-element composite hydroxide

YS/T 1499-2021 醋酸四氨铂

Platinum tetraammonium acetate

YS/T 1443-2021 镍钴二元素复合氢氧化物

Nickel-cobalt two-element composite hydroxide

ASTM B909-21a 非应力消除铝制品的平面应变断裂韧性试验的标准指南

1.1 This guide covers supplementary guidelines for planestrain fracture toughness testing of aluminum products for which complete stress relief is not practicable. Guidelines for recognizing when residual stresses may be significantly biasing test results are presented, as well as methods for minimizing the effects of residual stress during testing. This guide also provides guidelines for an empirical correction as well as interpretation of data produced during the testing of these products. Test Method E399 is the standard test method to be used for plane-strain fracture toughness testing of aluminum alloys. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Plane Strain Fracture Toughness Testing of Non-Stress Relieved Aluminum Products

T/FSYY 0009-2021 再生利用产品 电池用碳酸锂

再生利用产品 电池用碳酸锂

Recycled products — Lithium carbonate for batteries

ASTM B413-97a(2021) 精制银的标准规范

1.1 This specification covers refined silver cast bar2 form in three grades as follows: 1.1.1 Grade 99.90 (UNS P07020)—Silver having a minimum fineness of 999.0 commonly referred to as “commercial bar” or “bullion.” 1.1.2 Grade 99.95 (UNS P07015)—Silver having a minimum fineness of 999.5. 1.1.3 Grade 99.99 (UNS P07010)—A premium grade having a minimum fineness of 999.9. 1.2 The values stated in inch-pound units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards, including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Refined Silver

ASTM B914-21 钢的热浸镀锌用锌和锌合金锭上色码的标准实施规程

1.1 This standard is published with the following objectives: 1.1.1 To establish standard color codes for zinc, zinc alloy and zinc master alloy ingot used by the Hot-Dip Galvanizing industry, and 1.1.2 To standardize the use and application of these color codes. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel

ASTM B908-21 锌铸造合金锭色码使用的标准实施规程

Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot

ASTM B352/B352M-17(2021) 核应用用锆和锆合金薄板、带材和板材的标准规范

1.1 This specification covers hotand cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600 mm] or more in width; under 0.187 in. [4.8 mm] in thickness, 1.3.2 Strip, less than 24 in. [600 mm] in width; under 0.187 in. [4.8 mm] in thickness, and 1.3.3 Plate, over 10 in. [250 mm] in width; 0.187 in. [4.8 mm] and over in thickness. NOTE 1—Material over 0.187 in. [4.8 mm] in thickness and less than 10 in. [250 mm] wide is covered as bar in Specification B351/B351M. 1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application

ASTM B551/B551M-12(2021) 锆及锆合金带材、薄板和板材的标准规范

1.1 This specification2 covers five grades of zirconium strip, sheet, and plate. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate

YS/T 1433-2021 有色金属行业贵金属冶炼单位产品能源消耗限额

Energy consumption limit per unit product of precious metal smelting in the non-ferrous metal industry

YS/T 1432-2021 锂盐单位产品能源消耗限额

Lithium salt unit product energy consumption limit

YS/T 1431-2021 钼酸盐单位产品能源消耗限额

Molybdate unit product energy consumption limit

ASTM B737-10(2021) 热轧和/或冷轧铪棒和线的标准规格

1.1 This specification covers hotor cold-worked hafnium rod and wire. 1.2 This specification contains two material grades, one specifically for nuclear applications (Grade R1) and one for commercial alloying applications (Grade R3). 1.3 The products covered include the following: 1.3.1 Rod 3⁄8 to 1 in. (9.5 to 25 mm) in diameter. 1.3.2 Wire less than 3⁄8 in. (9.5 mm) in diameter. 1.4 Unless a single unit is used, for example, corrosion mass gain in mg/dm2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire

T/CNIA 0079-2021 绿色设计产品评价技术规范 乙二醇锑

本文件规定了乙二醇锑绿色设计产品评价的术语和定义、评价要求、产品生命周期评价报告编制方法，以及评价方法和流程。 本文件适用于以三氧化二锑为原料采用湿法工艺生产的乙二醇锑绿色设计产品的评价。

Ethylene glycol antimony product evaluation technical specification for green design

T/CNIA 0090-2021 废锂离子电池破碎分选集成设备

本文件规定了废锂离子电池破碎分选集成设备的技术要求、试验方法、检验规则和标志、包装、运输、贮存、随性文件和订货单内容。 本文件适用于废锂离子电池破碎分选集成设备。

Waste lithium ion battery crushing and sorting integrated equipment