77.150.99 其他有色金属产品 标准查询与下载

T/CNIA 0053-2020 铂炭催化剂

本标准规定了铂炭催化剂的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书及订货单（或合同）等内容。 本标准适用于精细化工、制药、香料、染料颜料、农药等行业的加氢、脱氢及还原过程使用的铂炭催化剂。

Platinum carbon catalyst

T/CNIA 0050-2020 氧化铝负载钌催化剂

本标准规定了氧化铝负载钌催化剂产品的技术要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书和订货单（或合同）内容。 本标准适用于合成环己醇、环己酮、己内酰胺、己二酸等化工行业用的氧化铝负载钌催化剂。

Alumina Supported Ruthenium Catalyst

T/CNIA 0056-2020 硫酸钡负载钯催化剂

本标准规定了硫酸钡负载钯催化剂的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书及订货单（或合同）等内容。 本标准适用于精细化工、制药、香料、染料颜料、农药等行业的加氢还原过程使用的硫酸钡负载钯催化剂。

Barium Sulfate Supported Palladium Catalyst

T/CNIA 0052-2020 钌锌催化剂

本标准规定了钌锌催化剂产品的术语和定义、技术要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书和订货单（或合同）内容。 本标准适用于化工行业合成己内酰胺、己二酸、环己醇、环己酮等用钌锌催化剂。

Ruthenium zinc catalyst

T/CNIA 0040-2020 钛及钛合金精密铸造用氧化锆

本标准规定了钛及钛合金精密铸造用氧化锆的技术要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与订货单（或合同）内容。 本标准适用于钛及钛合金精密铸造制壳用氧化锆(以下简称产品)。

Zirconia for precision casting of titanium and titanium alloys

T/CNIA 0057-2020 碳酸钙负载钯催化剂

本标准规定了碳酸钙负载钯催化剂的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书及订货单（或合同）等内容。 本标准适用于精细化工、石油化工、医药化工、香料化工、染料颜料工业、农药等领域使用的碳酸钙负载钯催化剂。

Calcium Carbonate Supported Palladium Catalyst

T/CNIA 0042-2020 小粒度钼铁压球

本标准规定了小粒度钼铁压球的技术要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书和订货单（或合同）内容。 本标准适用于炼钢、铸造或钼基合金材料中作为钼元素添加剂的小粒度钼铁压球。

Small particle size ferromolybdenum briquetting ball

T/CNIA 0055-2020 连续醋酐法生产高纯一氯乙酸用钯炭

本标准规定了连续醋酐法生产高纯一氯乙酸用钯炭（以下简称产品）的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书及订货单（或合同）内容。 本标准适用于连续醋酸法生产工艺中的连续氢化步骤所使用的钯炭催化剂。

Palladium Carbon for Production of High Purity Monochloroacetic Acid by Continuous Acetic Anhydride Process

T/CNIA 0054-2020 铑炭催化剂

本标准规定了铑炭催化剂的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书及订货单（或合同）等内容。 本标准适用于精细化工、制药等行业的加氢、脱基团、甲酰化及羰基化过程使用的铑炭催化剂。

Rhodium Carbon Catalyst

ASTM B365-12(2019) 钽及钽合金棒和线的标准规范

1.1 This specification covers unalloyed and alloyed tantalum rod and wire. 1.2 The materials covered by this specification are: 1.2.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both, 1.2.2 R05400, unalloyed tantalum, powder-metallurgy consolidation, 1.2.3 R05255, tantalum alloy, 90 % tantalum, 10 % tungsten, electron-beam furnace or vacuum-arc melt, or both, 1.2.4 R05252, tantalum alloy, 97.5 % tantalum, 2.5 % tungsten, electron-beam furnace or vacuum-arc melt, or both, and 1.2.5 R05240 tantalum alloy, 60 % tantalum, 40 % niobium, electron-beam furnace or vacuum-arc melt, or both. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Tantalum and Tantalum Alloy Rod and Wire

ASTM B386/B386M-19 钼和钼合金板、薄板、带材、箔材和带材的标准规范

Standard Specification for Molybdenum and Molybdenum Alloy Plate,Sheet, Strip, Foil, and Ribbon

ASTM B386/B386M-19e1 钼和钼合金板、薄板、带材、箔材和带材的标准规范

1.1 This specification covers unalloyed molybdenum and molybdenum alloy plate, sheet, strip, foil, and ribbon as follows: 1.1.1 Molybdenum 360—Unalloyed vacuum arc-cast molybdenum. 1.1.2 Molybdenum 361—Unalloyed powder metallurgy molybdenum. 1.1.3 Molybdenum Alloy 363—Vacuum arc-cast molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy. 1.1.4 Molybdenum Alloy 364—Powder metallurgy molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy. 1.1.5 Molybdenum 365—Unalloyed vacuum arc-cast molybdenum, low carbon. 1.1.6 Molybdenum Alloy 366—Vacuum arc-cast molybdenum-30 % tungsten alloy. 1.1.7 Drawing Grade—A drawing grade is defined, which may be specified as a separate requirement by the purchaser. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.2.1 The ball punch deformation test called for in 8.4 is a test that is specified in the inch-pound system, and original test results used to produce Fig. 2 were all obtained using inchpound measurements. For this reason, the graph of minimum required cup height as a function of sheet thickness has been retained in its original inch-pound system. The graphical data has been scanned and a straight line fitted to the scan data. The equation of this line is included in both inch-pound and SI units. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Molybdenum and Molybdenum Alloy Plate,Sheet, Strip, Foil, and Ribbon

ASTM B550/B550M-07(2019) 锆及锆合金棒材和线材的标准规范

1.1 This specification2 covers three grades of zirconium and zirconium alloy bar and wire. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test methods portions of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zirconium and Zirconium Alloy Bar and Wire

ASTM B521-19 钽及钽合金无缝和焊接管标准规范

Standard Specification for Tantalum and Tantalum Alloy Seamless and Welded Tubes

ASTM B708-12(2019) 钽和钽合金板、薄板和带材的标准规范

1.1 This specification covers unalloyed and alloyed tantalum plate, sheet, and strip as follows. 1.1.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both, 1.1.2 R05400, unalloyed tantalum, powder-metallurgy consolidation, 1.1.3 R05255, tantalum alloy, 90 % tantalum, 10 % tungsten, electron-beam furnace of vacuum-arc melt, or both, 1.1.4 R05252, tantalum alloy, 97.5 % tantalum, 2.5 % tungsten, electron-beam furnace or vacuum-arc melt, or both, and 1.1.5 R05240, tantalum alloy, 60 % tantalum, 40 % niobium, electron-beam furnace or vacuum-arc melt. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety and/or health problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Tantalum and Tantalum Alloy Plate, Sheet, and Strip

YS/T 1332.3-2019 粗制铜钴原料化学分析方法 第3部分：硫含量的测定 高频燃烧-红外光谱法

Methods for chemical analysis of crude copper and cobalt raw materials Part 3: Determination of sulfur content High frequency combustion-infrared spectroscopy

YS/T 1321-2019 1,2-双二苯基膦乙烷氯化钯

1,2-Bisdiphenylphosphineethanepalladium chloride

YS/T 1306-2019 铼条

Rhenium bar

YS/T 1324-2019 四氯钯酸钠

Sodium tetrachloropalladate

YS/T 1325-2019 四正丙基过钌酸铵

Tetra-n-propyl ammonium perruthenate