77.150.99 其他有色金属产品 标准查询与下载

YS/T 221-2011 金属铍珠

本标准规定了金属铍珠的要求、试验方法、检验规则及标志、包装、运输、贮存、质量证明书和合同（或订货单）内容。 本标准适用于氟化铍镁热还原法制得的金属铍珠。

Beryllium metal pebbles

YS/T 756-2011 碳酸铯

本标准规定了碳酸铯的要求、试验方法、检验规则以及标志、包装、运输、贮存、质量证明书和合同（或订货单）内容。 本标准适用于采用合成法生产的碳酸铯。

Cesium carbonate

ASTM B653/B653M-11(2016) 无缝和焊接的锆和锆合金焊接配件的标准规格

1.1 This specification covers fittings, factory made from three grades of zirconium and zirconium alloys. The term welding fittings applies to butt-welding parts such as 45 and 90° elbows, 180° returns, caps, tees, reducers, lap-joint stub ends, and other types. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings

ASTM B352/B352M-11 核应用锆及锆合金板,薄板和带材标准规格

1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600 mm] or more in width; under 0.187 in. [4.8 mm) in thickness, 1.3.2 Strip, less than 24 in. [600 mm] in width; under 0.187 in. [4.8 mm] in thickness, and 1.3.3 Plate, over 10 in. [250 mm] in width; 0.187 in. [4.8 mm] and over in thickness. Note 18212;Material over 0.187 in. [4.8 mm] in thickness and less than 10 in. [250 mm] wide is covered as bar in Specification B351/B351M. 1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application

ASTM B350/B350M-11 核应用锆和锆合金铸锭标准规格

For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

ASTM B884-11 用于超导的铌钛合金坯料,棒材和条材标准规格

1.1 This specification covers niobium-titanium alloy billets, bars, and rods, at 46 to 48 % titanium. This material is used in the manufacture of wire for superconducting applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Niobium-Titanium Alloy Billets, Bar, and Rod for Superconducting Applications

ASTM B653/B653M-11 无缝和焊接锆及锆合金锻造配件标准规格

1.1 This specification covers fittings, factory made from three grades of zirconium and zirconium alloys. The term welding fittings applies to butt-welding parts such as 45 and 90° elbows, 180° returns, caps, tees, reducers, lap-joint stub ends, and other types. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings

ASTM B350/B350M-11(2016)e1 核设备用锆和锆合金锭规格

10.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. 1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

YS/T 222-2010 碲锭

本标准规定了碲锭的要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与合同(或订货单)内容。 本标准适用于由有色金属冶炼过程中所得含碲的阳极泥、烟灰及其他物料,经湿法冶金处理生产的碲锭。

Tellruium ingots

YS/T 741-2010 氧化镓

本标准规定了氧化镓(GaO)的要求、试验方法、检验规则、包装、运输、贮存等。 本标准适用于生产发光材料、晶体材料、催化剂及其他制品用原料氧化镓(99.9%-99.999%)。

Gallium oxide

YS/T 744-2010 电池级无水氯化锂

本标准规定了电池级无水氯化锂的要求、试验方法、检验规则和标志、包装、运输、贮存、质量证明书及订货单(或合同)内容。 本标准适用于以各种原料制得的无水氯化锂,产品主要用于一步电解制取电池级金属锂,也可用于制造焊接材料、空调和作为高分子材料合成催化剂等。

Battery grade anhydrous lithium chloride

YS/T 42-2010 钽酸锂单晶

本标准规定了钽酸锂单晶的要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和合同(或订货单)内容。 本标准适用于提拉法生长的钽酸锂原生单晶经磨外圆后的产品。

Lithium tantalate single crystals

ASTM B737-10 热轧和/或冷轧铪棒和线的标准规格

1.1 This specification covers hot- or cold-worked hafnium rod and wire. 1.2 This specification contains two material grades, one specifically for nuclear applications (Grade R1) and one for commercial alloying applications (Grade R3). 1.3 The products covered include the following: 1.3.1 Rod 3/8 to 1 in. (9.5 to 25 mm) in diameter. 1.3.2 Wire less than 3/8 in. (9.5 mm) in diameter. 1.4 Unless a single unit is used, for example, corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire

ASTM B495-10 锆和锆合金铸锭的标准规范

1.1 This specification covers six grades of zirconium ingots. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots

ASTM B495-10(2017) 锆及锆合金锭的标准规格

1.1 This specification covers six grades of zirconium ingots. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zirconium and Zirconium Alloy Ingots

ASTM B652/B652M-10 铌-铪合金铸锭用标准规范

The following applies to all specified limits in this standard for purposes of determining conformance with this specification: The observed value or a calculated value shall be rounded off to the nearest unit in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.1 This specification covers hafnium alloyed niobium ingots prepared by vacuum- or plasma- arc melting or electron-beam furnace melting, or a combination of these methods, to produce consolidated metal for processing to various mill shapes. 1.2 The material covered by this specification is Grade R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Niobium-Hafnium Alloy Ingots

ASTM B655/B655M-10 铌-铪合金棒材和线材用标准规范

The following applies to all specified limits in this standard for purposes of determining conformance with this specification. The observed value or a calculated value shall be rounded off to the nearest unit in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.1 This specification covers hafnium alloyed niobium bar and wire. 1.2 The material covered by this specification is R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Niobium-Hafnium Alloy Bar and Wire

ASTM B387-10 钼及钼合金棒材、杆材和线材的标准规范

1.1 This specification covers unalloyed molybdenum and molybdenum alloy bar, rod, and wire as follows: 1.1.1 Molybdenum 3608212;Unalloyed vacuum arc-cast molybdenum. 1.1.2 Molybdenum 3618212;Unalloyed powder metallurgy molybdenum. 1.1.3 Molybdenum Alloy 3638212;Vacuum arc-cast molybdenum-0.5% titanium-0.1% zirconium (TZM) alloy. 1.1.4 Molybdenum Alloy 3648212;Powder metallurgy molybdenum-0.5% titanium-0.1% zirconium (TZM) alloy. 1.1.5 Molybdenum 3658212;Unalloyed vacuum arc-cast molybdenum, low carbon. 1.1.6 Molybdenum Alloy 3668212;Vacuum arc-cast molybdenum, 30% tungsten alloy. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Standard Specification for Molybdenum and Molybdenum Alloy Bar, Rod, and Wire

GOST R 54152-2010 电镀用L90铜带.规范

Tapes and strips from L90 brass for plating. Specifications

GOST R 54151-2010 铂合金催化纱布.规范

Platinum alloys catalytic gauzes. Specifications