共找到 492 条与 木基板材综合 相关的标准,共 33 页
Reconstituted wood-based panels - Methods of test - Surface soundness
Reconstituted wood-based panels - Methods of test - Swelling in thickness after immersion in water
Reconstituted wood-based panels - Methods of test - Wet bending strength after immersion in water at 70oC or boiling temperature
Reconstituted wood-based panels - Methods of test - Resistance to axial withdrawal of screws
Reconstituted wood-based panels - Methods of test - Dimensional changes associated with changes in relative humidity
Reconstituted wood-based panels - Methods of test - Formaldehyde emission - Desiccator method
Reconstituted wood-based panels - Methods of test - Surface absorption
Reconstituted wood-based panels - Methods of test - Assessing appearance of melamine overlaid panels
Reconstituted wood-based panels - Methods of test - Resistance to surface abrasion (Taber abrasion test)
This European Standard specifies methods for the verification of compliance of one or more properties of an isolated lot of wood-based panels with the requirements of the relevant EN specification standards.
Wood-based panels - Sampling, cutting and inspection - Part 3: Inspection of an isolated lot of panels
This European Standard specifies methods for the verification of compliance of one or more properties of an isoleted lot of wood-based panels with the requirements of the relevant EN specification standards. Different sample sizes are given depending on wether or not the production is controlled according to EN 326-2. For panels, the production of which is controlled in accordance to EN 326-2 this European Standard can be used in case of a dispute. It is not applicable for the factory production control. For these purposes, EN 326-2 applies. In this standard, verification of compliance is based on the testing of small test pieces.#,,#
Wood-based panels - Sampling, cutting and inspection - Part 3: Inspection of an isolated lot of panels; German version EN 326-3:2003
Timber Structures - Test Methods - Determination of Mechanical Properties of Wood-Based Panels
This European Standard specifies a chamber method with three options of test chambers for the determination of the formaldehyde emission from wood-based panels in terms of the steady-state concentration in a climate chamber under defined conditions,which relate to typical conditions in real-life.This chamber method can also be applied to the estimate of formaldehyde concentrations under various conditions in practice,by the use of mathematical models.This standard can also be used for the testing of formaldehyde emissions of products other than wood-based panels.
Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method
Wood-based panels - Floating floors - Part 1: Performance specifications and requirements
This European Standard specifies methods for the verification of compliance of one or more properties of an isolated lot of wood-based panels with the requirements of the relevant EN specification standards. Different sample sizes are given depending on whether or not the production is controlled according to EN 326-2. For panels, the production of which is controlled in accordance to EN 326-2 this European Standard can be used in case of a dispute. It is not applicable for the factory production control. For these purposes, EN 326-2 applies. In this standard, verification of compliance is based on the testing of small test pieces.
Wood-based panels - Sampling, cutting and inspection - Part 3:Inspection of an isolated lot of panels
This International Standard specifies a test method for the determination of the moisture resistance of wood-based panels under cyclic test conditions.
Wood-based panels - Determination of moisture resistance under cyclic test conditions
This Technical Specification specifies test methods for loading a continuously fully supported non-structural floating floor with static concentrated point loads, alternating loads and dynamic impact loads for determining the values of the resulting deflections. NOTE These test methods form part of the basis for classification of floating floor constructions. The requirements, i.e. load values, number of load cycles, and deflection limits for the different load categories, are given in EN 13810-1.
Wood-based panels. Floating floors. Test methods
This Technical Specification specifies test methods for loading a continuously fully supported non-structural floating floor with static concentrated point loads, alternating loads and dynamic impact loads for determining the values of the resulting deflections.
Wood-based panels - Floating floors - Part 2: Test methods
This International Standard specifies a method for assessing the surface soundness of coated wood-based panels and uncoated particleboards, wet and dry-process fibreboards and cement-bonded particleboards. NOTE The grid-patterned face (screen side) of hardboards cannot be tested according to this International Standard.
Wood-based panels - Determination of surface soundness
This International Standard specifies certain rules for the sampling and cutting of test pieces. It does not cover the sampling and cutting of test pieces for the derivation of characteristic values for structural design. These tests are carried out on medium-sized test pieces.
Wood-based panels - Sampling and cutting of test pieces
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号