共找到 492 条与 木基板材综合 相关的标准,共 33 页
This International Standard specifies a method of test for evaluating the bond quality of particleboards, OSB and fibreboards, intended for use in humid conditions.
Wood-based panels - Determination of moisture resistance - Boil test
This International Standard specifies a method for determining the apparent modulus of elasticity and bending strength of wood-based panels in flatwise bending.
Wood-based panels - Determination of modulus of elasticity in bending and of bending strength
This International Standard specifies a method for determining the density of wood-based panels.
Wood-based panels - Determination of density
This Technical Specification specifies test methods for loading a continuously fully supported non-structural floating floor with static concentrated point loads, alternating loads and dynamic impact loads for determining the values of the resulting deflections. NOTE: These test methods form part of the basis for classification of floating floor constructions. The requirements, i.e. load values, number of load cycles, and deflection limits for the different load categories, are given in prEN 13810-1.#,,#
Wood-based panels - Floating floors - Part 2: Test methods; German version CEN/TS 13810-2:2003
This European Standard provides the performance specifications and requirements for wood-based panels used in continuously fully supported non-structural floating floors.
Wood-based panels - Floating floors - Part 1: Performance specifications and requirements; German version EN 13810-1:2002
This document describes a procedure for determination of formaldehyde release from coated and uncoated wood-based panels under defined conditions.
Corrigenda to DIN EN 717-2:1995-01 (EN 717-2:1994/AC:2002)
This International Standard specifies a method for measuring the thickness, length and width of test pieces of wood-based panels.
Wood-based panels - Determination of dimensions of test pieces
This International Standard specifies methods for measuring the thickness, width and length, as well as the squareness, edge straightness and flatness of wood-based panels. It applies to full-size flat panels.
Wood-based panels - Determination of dimensions of panels
This European standard provides the performance specifications and requirements for wood-based panels used in continously fully supported non-structural floating floors.
Wood-based panels - Floating floors - Part 1: Performance specifications and requirements
This International Standard specifies a method for determining the moisture content of wood-based panels.
Wood-based panels - Determination of moisture content
This International Standard specifies a method for determining the resistance to tension perpendicular to the plane of the panel, also known as "internal bond", of particleboards, OSB, fibreboards, and cement-bonded particleboards.
Wood-based panels - Determination of tensile strength perpendicular to the plane of the panel
This International Standard specifies a method for the determination of dimensional changes in wood-based panels, due to variations in relative humidity.
Wood-based panels - Determination of dimensional changes associated with changes in relative humidity
This International Standard specifies a method for determining the swelling in thickness of flat-pressed or drum-pressed particleboards, fibreboards, OSB, and cement-bonded particleboards, after immersion in water.
Wood-based panels - Determination of swelling in thickness after immersion in water
Fancy veneer overlaid glulam for decorative use
Wood based panels - Determination of dimensional changes associated with changes in relative humidity
Wood-based panels - Determination of edgewise bending properties
This Technical Specification specifies test methods for loading a continuously fully supported non-structural floating floor with static concentrated point loads, alternating loads and dynamic impact loads for determining the values of the resulting deflections.
Wood-based panels - Floating floors - Part 2: Test methods
Wood-based panels - Floating floors - Part 1 : performance specifications and requirements.
Esta Norma Europeia especifica os métodos para a verifica??o de conformidade de uma ou mais propriedades de uma remessa de placas com os requisitos de um contrato, ou com os valores anunciados das propriedades das placas numa remessa como documentado pelo fornecedor. Esta Norma Europeia n?o é aplicável para controlo interno ou externo de conformidade dos produtos na fábrica. Para esse fim, aplica-se prEN 326-2. Nesta Norma Europeia, a verifica??o de conformidade é baseada no ensaio de provetes pequenos.
Wood-based panels Sampling,cutting and inspection Part 3:Inspection of a consignment of panels
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号