79.060.01 木基板材综合 标准查询与下载

AS/NZS 4266.35(Int):2001 再生木基板．试验方法．试样的尺寸

Reconstituted wood-based panels - Methods of test - Dimensions of test pieces

AS/NZS 4266.34(Int):2001 再生人造板．测试方法．表面吸收性

Reconstituted wood-based panels - Methods of test - Surface absorption

AS/NZS 4266.16(Int):2001 再生木基板．试验方法．甲醛排放．干燥器法

Reconstituted wood-based panels - Methods of test - Formaldehyde emission - Desiccator method

AS/NZS 4266.13(Int):2001 再生木基板．试验方法．螺钉耐轴向抽出的性能

Reconstituted wood-based panels - Methods of test - Resistance to axial withdrawal of screws

AS/NZS 4266.11(Int):2001 再生木基板．试验方法．循环试验条件下的耐潮性

Reconstituted wood-based panels - Methods of test - Moisture resistance under cyclic test conditions

AS/NZS 4266.5(Int):2001 再生人造板．测试方法．弯曲和弯曲强度的弹性模数

Reconstituted wood-based panels - Methods of test - Modulus of elasticity in bending and bending strength

AS/NZS 4266.7(Int):2001 再生木基板．试验方法．表面坚固性

Reconstituted wood-based panels - Methods of test - Surface soundness

AS/NZS 4266.10(Int):2001 再生人造板．测试方法．浸入70摄氏度或沸点水中之后的湿弯曲强度

Reconstituted wood-based panels - Methods of test - Wet bending strength after immersion in water at 70 degrees Celsius or boiling temperature

AS/NZS 4266.1(Int):2001 再生木基板．试验方法．试样的取样和切割

Reconstituted wood-based panels - Methods of test - Sampling and cutting of test pieces

AS/NZS 4266.2(Int):2001 再生人造板．测试方法．尺寸，垂直度，平直度和边缘直线度

Reconstituted wood-based panels - Methods of test - Dimensions, squareness, flatness and edge straightness

AS/NZS 4266.3(Int):2001 再生木基板．试验方法．水分含量

Reconstituted wood-based panels - Methods of test - Moisture content

ONORM B 3003-2000 人造板．额外试验方法

Die nachfolgend beschriebenen Prüfmethoden sind für die Bestimmung von Eigenschaften gedacht, die für den Einsatz von Holzwerkstoffplatten (wie Span-, Faser-, Sperrholz- und Massivholzplatten) für spezielle Verwendungen von Bedeu-tung sind.

Wood based panels-Additional test methods

BS EN 326-2:2000 木基板.抽样、切削和检验.工厂中的质量控制

This European Standard specifies methods for both factory production control and external control of conformity of the properties of wood-based panels with the relevant EN specifications. However, it may also apply, at the option of the manufacturer, to wood-based panels applied for non-construction purposes. This European Standard is not applicable for the assessment of conformity with specifications of the properties of panels comprised in consignments. In such cases, EN 326-3 applies. For factory production control, if required, methods for the assessment of conformity of batches and of production over longer periods are given. For external control, if required, methods for the initial inspection of a factory and initial type testing of a product, and for the surveillance of the factory production control, are given. In this standard, control is based on the testing of small test pieces.

Wood-based panels - Sampling, cutting and inspection - Part 2: Quality control in the factory

ASTM E1307-00 平屋面板用预处理的非金属复合面与结构芯的表面制备和结构粘合的标准实施规程

1.1 This practice covers the materials, processes, and quality controls to be used in the manufacture of durable adhesive bonded, nonmetallic faced, flat sandwich panels for rigid wall relocatable shelters. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Surface Preparation and Structural Adhesive Bonding of Precured, Nonmetallic Composite Facings to Structural Core for Flat Shelter Panels

SNI 01-6243.2-2000 桌子连接板及连接板条

Jointed board and jointed stick for tables

SNI 01-6243.1-2000 窗框和门框

Jointed board and jointed stick for window frame and door frame

LST EN 310-1999 人造板 弯曲弹性模量和弯曲强度的测定

Wood-based panels - Determination of modulus of elasticity in bending and of bending strength

LST EN 326-1-1999 人造板 取样、切割和检验 第1部分：试件的取样和切割以及试验结果的表示

Wood-based panels - Sampling, cutting and inspection - Part 1: Sampling and cutting of test pieces and expression of test results

LST EN 120-1999 人造板甲醛含量的测定称为穿孔法的提取法

Wood based panels - Determination of formaldehyde content - Extraction method called the perforator method

LST EN 323-1999 人造板 密度的测定

Wood-based panels - Determination of density