79.080 半成品材 标准查询与下载

DS/EN 14354/AC:2007 人造板 木饰面地板覆盖物

This European standard specifies definitions, requirements and test methods for wood veneer floor coverings for internal use.

Wood-based panels - Wood veneer floor covering

DS/EN 13307-1:2007 非结构用途的木材坯料和半成品型材 第1部分：要求

This European Standard specifies requirements for timber blanks and semi-finished profiles for non-structural uses, including glued laminated and glued finger jointed products. This Standard gives specific requirements for dimensions, stability and moisture content. This Standard applies to hardwood and to softwood for use in joinery.Production control requirements and tests are given in prCEN/TS 13307-2.

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements

DS/EN 15146:2007 实心软木镶板和覆层 无榫槽的机加工型材

This European Standard defines the characteristics of solid wood panelling and cladding without tongue and groove on edges, machined from the following most common European species of softwood: spruce/fir, pine, larch, European Douglas fir and maritime pine. Products are intended for interior or exterior use.Coatings and finishings are not dealt with in this European Standard.NOTE products sold in the European Economic Area will have to comply with EN 14915.

Solid softwood panelling and cladding - Machined profiles without tongue and groove

LY/T 1700-2007 地采暖用木质地板

本标准规定了地采暖用木质地板的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于铺设在地面供暖系统上的木质地板。

Wood based flooring for ground with heating system

LST EN 15146-2007 实心软木镶板和覆层 无榫槽的机加工型材

Solid softwood panelling and cladding - Machined profiles without tongue and groove

LST EN 13307-1-2007 非结构用途的木材坯料和半成品型材 第1部分：要求

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements

NF B53-667*NF EN 15146:2007 实心软木镶板和覆层.不带舌簧和凹槽的机械剖面

Solid softwood panelling and cladding - Machined profiles without tongue and groove.

DIN EN 15146:2007 实芯软木镶板和层板.不带舌和槽的机加工轮廓

This European Standard defines characteristics of solid wood panelling and cladding without tongue and groove on edges machined from the following most common European species of softwood: spruce/fir, pine, larch, European Douglas fir and maritime pine. Products are intended for interior or exterior use. Coatings and finishings are not dealt with in this European Standard. NOTE products sold in the European Economic Area will have to comply with EN 14915.

Solid softwood panelling and cladding - Machined profiles without tongue and groove; English version of DIN EN 15146:2007-03

LST EN 14354-2005/AC-2007 人造板 木饰面地板覆盖物

Wood-based panels - Wood veneer floor covering

DIN EN 14354 Berichtigung 1:2007 木质板条.木质薄地板覆盖物

This document specifies definitions, requirements and test methods for wood veneer floor coverings for internal use. It gives guidance for the evaluation of conformity of the products to the requirements of this standard. Wood-veneer floor coverings without finishing are excluded.#,,#

Wood-based panels - Wood veneer floor covering; German version EN 14354:2004, Corrigenda to DIN EN 14354:2005-03; German version EN 14354:2004/AC:2006

BS EN 15146:2007 实心软木厚镶板层板 不带舌和槽的机加工形状

Solid softwood panelling and cladding - Machined profiles without tongue and groove

BS EN 15146:2006 实心软木厚镶板层板.不带舌和槽的机加工形状

This European Standard defines the characteristics of solid wood panelling and cladding without tongue and groove on edges, machined from the following most common European species of softwood: spruce/fir, pine, larch, European Douglas fir and maritime pine. Products are intended for interior or exterior use. Coatings and finishings are not dealt with in this European Standard. NOTE products sold in the European Economic Area will have to comply with EN 14915.

Solid softwood panelling and cladding - Machined profiles without tongue and groove

LST EN 14915-2007 实木镶板和覆层 特性、合格评定和标记

Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking

DIN EN 13307-1:2007 不作结构材料用木制坯件和半成品材.第1部分:要求

This European Standard specifies requirements for timber blanks and semi-finished profiles for non-structural uses, including glued laminated and glued finger jointed products. This Standard gives specific requirements for dimensions, stability and moisture content. This Standard applies to hardwood and to softwood for use in joinery. Production control requirements and tests are given in prCEN/TS 13307-2.

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements; English version of DIN EN 13307-1:2007-01

CAN/CSA-O122-2006(C2011) 胶合层压结构木材

1 Domaine d'application 1.1 Cette norme prescrit les exigences minimales relatives à la fabrication du bois lamellé-collé des essences énumérées dans la CAN/CSA-O86. Cette norme ne tient pas compte de l'entreposage, de la manutention ni de la mise en oeuvre de ces produits fabriqués. 1.2 Les critères de calcul pour le bois lamellé-collé fabriqué conformément à cette norme sont traités dans la CAN/CSA-O86. 1.3 Dans les normes CSA, le terme «doit» indique une exigence, c'est-à-dire une prescription que l'utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu'il est conseillé mais non obligatoire de faire et «peut», une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent ni prescriptions ni recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas de figures et des tableaux font partie de ceux-ci et peuvent être rédigés comme des prescriptions. Les légendes des figures et des équations font également partie de celles-ci. La désignation «normative» (obligatoire) ou «informative» (facultative) est attribuée aux annexes pour en définir l'application. 1.4 Cette norme est rédigée en unités SI (système métrique). Pour la conversion de ces unités en verge/livre (système anglo-saxon), voir l'annexe A.

Glued laminated structural timber

BS EN 13307-1:2006 不作结构材料的木制坯件和半成品材.要求

This European Standard specifies requirements for timber blanks and semi-finished profiles for non-structural uses, including glued laminated and glued finger jointed products. This Standard gives specific requirements for dimensions, stability and moisture content. This Standard applies to hardwood and to softwood for use in joinery. Production control requirements and tests are given in prCEN/TS 13307-2.

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements

NF B53-675:2006 实心木质镶板和贴面层.特性、合格评定和标记

Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking.

DIN EN 14915:2006 实心木质镶板和贴面层.特性、合格评定和标记

This European Standard defines and specifies the relevant characteristics and the appropriate test methods to determine these characteristics for products (including sidings) used in solid wood panelling and cladding for: - wall and ceiling panelling for internal use; - wall and ceiling cladding for external uses. It provides for the evaluation of conformity and the requirements for marking these products. The products are not evaluated for stiffening functions. This European Standard covers treated as well as untreated wood and it covers finger jointed and edge glued products. This European Standard covers products in compliance with EN 14519, EN 14951 and prEN 15146 but it also covers other solid timber products suitable for panelling and cladding. This European Standard does not cover products which are produced from laminated layer section.

Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking; English version of DIN EN 14915:2006-11

DS/EN 14951:2006 实心硬木镶板和覆层 机加工型材元件

This document specifies the characteristics of solid hardwood panelling and cladding elements with or without grooves and/or tongues, for interior or exterior use.It does not cover characteristics of the possible coating system.NOTE 1 Products sold in The European Economic Area will have to comply with prEN 14915.NOTE 2 For softwood see EN 14519.

Solid hardwood panelling and cladding – Machined profiles elements

BS EN 14915:2006 实心木质镶板和贴面层.特征、合格评定和标记

This European Standard defines and specifies the relevant characteristics and the appropriate test methods to determine these characteristics for products (including sidings) used in solid wood panelling and cladding for: ? wall and ceiling panelling for internal use; ? wall and ceiling cladding for external uses. It provides for the evaluation of conformity and the requirements for marking these products. The products are not evaluated for stiffening functions. This European Standard covers treated as well as untreated wood and it covers finger jointed and edge glued products. This European Standard covers products in compliance with EN 14519, EN 14951 and prEN 15146 but it also covers other solid timber products suitable for panelling and cladding. This European Standard does not cover products which are produced from laminated layer section.

Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking