81.060.20 陶瓷制品 标准查询与下载

CNS 981-1994 日用瓷器

本标准适用于一般餐饮用之日用瓷器。

Porcelain Tablewares

ASTM C738-94(2016) 从釉面陶瓷表面上提取的铅和镉的标准试验方法

1.1 This test method covers the precise determination of lead and cadmium extracted by acetic acid from glazed ceramic surfaces. The procedure of extraction may be expected to accelerate the release of lead from the glaze and to serve, therefore, as a severe test that is unlikely to be matched under the actual conditions of usage of such ceramic ware. This test method is specific for lead and cadmium. 1.2 The values stated in SI (metric) units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Lead and Cadmium Extracted from Glazed Ceramic Surfaces

JIS R 4302:1993 测定薄钢板上釉和瓷时浸渍重量损失的试验方法

この規格は，ほうろう加工に用いる鋼板の酸洗減量測定方法について規定する。

Testing method for determining pickling weight loss of sheet steel for vitreous and porcelain enamelling

ASTM C554-93(2011) 用热冲击法测定焙烧上釉卫生陶瓷器抗裂开的标准试验方法

Unless there is a proper match between the expansions of the glaze and the body, all glazed whitewares may contain residual stresses from the firing that bonded the glaze to the body. In addition, whitewares are increasingly subjected to thermal stresses in service. Hence, an important use criterion for a glazed whiteware is adequate resistance to repeated abrupt thermal changes. In most cases, the result of inadequate resistance to thermal shock is the appearance of a craze pattern in the glaze. This craze pattern is visible by inspection with oblique lighting and application of a suitable ink or dye. This test method is applicable to vitreous whitewares that have negligible crazing as a result of moisture expansion. For nonvitreous and semivitreous bodies, refer to Test Method C424.1.1 This test method covers the determination of the resistance to crazing of fired, glazed, ceramic whitewares when stresses residual after glost firing may cause a tendency to craze, such stresses being induced by factors other than moisture expansion. 1.2 This test is not intended to induce moisture expansion, which fact should be kept in mind if the materials to be evaluated may exhibit moisture expansion. Note 18212;Test Method C424 covers a method for determining resistance to crazing induced by moisture expansion. Its use is generally confined to testing nonvitreous and semivitreous ceramic whitewares because these products may be subject to such expansion. For whitewares with negligible moisture expansion (such as vitreous and impervious ware), the thermal shock method described herein is generally to be preferred. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Warning in 6.3. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.

Standard Test Method for Crazing Resistance of Fired Glazed Ceramic Whitewares by a Thermal Shock Method

ASTM C554-93(2016) 采用热冲击法测定烧结上釉白瓷瓷器的抗龟裂性的标准试验方法

3.1 Unless there is a proper match between the expansions of the glaze and the body, all glazed whitewares may contain residual stresses from the firing that bonded the glaze to the body. In addition, whitewares are increasingly subjected to thermal stresses in service. Hence, an important use criterion for a glazed whiteware is adequate resistance to repeated abrupt thermal changes. In most cases, the result of inadequate resistance to thermal shock is the appearance of a craze pattern in the glaze. This craze pattern is visible by inspection with oblique lighting and application of a suitable ink or dye. 3.2 This test method is applicable to vitreous whitewares that have negligible crazing as a result of moisture expansion. For nonvitreous and semivitreous bodies, refer to Test Method C424. 1.1 This test method covers the determination of the resistance to crazing of fired, glazed, ceramic whitewares when stresses residual after glost firing may cause a tendency to craze, such stresses being induced by factors other than moisture expansion. 1.2 This test is not intended to induce moisture expansion, which fact should be kept in mind if the materials to be evaluated may exhibit moisture expansion. Note 1: Test Method C424 covers a method for determining resistance to crazing induced by moisture expansion. Its use is generally confined to testing nonvitreous and semivitreous ceramic whitewares because these products may be subject to such expansion. For whitewares with negligible moisture expansion (such as vitreous and impervious ware), the thermal shock method described herein is generally to be preferred. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Warning in 6.3.

Standard Test Method for Crazing Resistance of Fired Glazed Ceramic Whitewares by a Thermal Shock Method

CNS 12970-1992 瓷质金斗与骨灰坛检验法

本标准规定瓷质金斗与骨灰?之检验方法。

Method of Test for Porcelain Jars for Bones and Bone Ashes

CNS 12969-1992 瓷质金斗与骨灰坛

本标准适用于盛装入体骨骼用之金斗或火葬后用以盛装骨灰之?。

Porcelain Jars for Bones and Bone Ashes

SNI 02-2624-1992 饮用水烛形过滤器

Ceramic drinking water filter candle

JIS R 3311:1991 陶瓷纤维毡

この規格は，アルミナンリカ系繊維のプランケソト1260°C標準グレードについて規定する。

Ceramic fiber blanket

JIS R 1201:1991 陶瓷管

この規格は，陶製円形管(以下，管という。)について規定する。

Clay pipes

JIS R 1534:1991 化学工业用耐酸瓷带圆锥法兰管的金属接头

Metal joint for conical flange pipes of acid proof porcelains for chemical industry

JIS R 1511:1991 化学工业用耐酸瓷带圆锥法兰的直管

Conical flanged straight pipes of acid proof porcelains for chemical industry

JIS R 1512:1991 化学工业用耐酸瓷带圆锥法兰的90度弯管

Conical flanged 90 degrees bent pipes of acid proof porcelains for chemical industry

JIS R 1513:1991 化学工业用耐酸瓷带圆锥法兰的45度弯管

Conical flanged 45 degrees bent pipes of acid proof porcelains for chemical industry

JIS R 1514:1991 化学工业用耐酸瓷带圆锥法兰的T型管

Conical flanged tee pipes of acid proof porcelains for chemical industry

JIS R 1528:1991 化学工业用耐酸瓷塔形填料

この規格は，化学工業用耐酸磁器製充てん物(以下，充てん物という。)について規定する。

Tower packings of acid proof porcelains for chemical industry

GOST 17612-1989 陶瓷耐酸喷嘴.技术条件

Настоящий стандарт распространяется на кислотоупорные керамические насадки, предназначенные для заполнения насадочных колонн и другой

Ceramic acid-resistant pocking rings. Specifications

ASTM C329-88(2016) 焙烧卫生陶瓷材料比重的标准试验方法

3.1 Measurement of specific gravity is a tool for determining the degree of maturation of a ceramic body. 1.1 This test method covers the determination of specific gravity of fired ceramic whiteware materials under prescribed conditions. Note 1: This test method is not applicable to materials attacked by water. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Specific Gravity of Fired Ceramic Whiteware Materials

ASTM C408-88(2016) 卫生陶瓷制品热导率的标准试验方法

2.1 This test method provides information useful in understanding and quantifying such parameters as thermal shock resistance and ability to conduct or dissipate heat. 1.1 This test method covers a general procedure2 for determining the thermal conductivity of whiteware ceramics over the temperature range from 100 to 300°F (40 to 150°C). 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) units given in parentheses are for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Conductivity of Whiteware Ceramics

ASTM C849-88(2016) 白陶瓷品的努氏压痕硬度的标准试验方法

5.1 The Knoop indentation hardness is one of many properties that is used to characterize ceramic whitewares. Attempts have been made to relate Knoop indentation hardness to tensile strength, grinding speeds, and other hardness scales, but no generally accepted methods are available. Such conversions are limited in scope and should be used with caution, except for special cases where a reliable basis for the conversion has been obtained by comparison tests. 1.1 This test method covers the determination of the Knoop indentation hardness of ceramic whitewares and the verification of Knoop indentation hardness testing machines using standard glasses. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares