81.060.30 高级陶瓷 标准查询与下载

ASTM C1468-19a 室温下连续纤维增强高级陶瓷的横向拉伸强度的标准试验方法

1.1 This test method covers the determination of transthickness tensile strength ~SU T ! under monotonic uniaxial tensile loading of continuous fiber-reinforced ceramics (CFCC) at ambient temperature. This test method addresses, but is not restricted to, various suggested test specimen geometries, test fixtures, data collection, and reporting procedures. In general, round or square test specimens are tensile tested in the direction normal to the thickness by bonding appropriate hardware to the samples and performing the test. For a Cartesian coordinate system, the x-axis and the y-axis are in the plane of the test specimen. The transthickness direction is normal to the plane and is labeled the z-axis for this test method. For CFCCs, the plane of the test specimen normally contains the larger of the three dimensions and is parallel to the fiber layers for unidirectional, bidirectional, and woven composites. Note that transthickness tensile strength as used in this test method refers to the tensile strength obtained under monotonic uniaxial tensile loading, where “monotonic” refers to a continuous nonstop test rate with no reversals from test initiation to final fracture. 1.2 This test method is intended primarily for use with all advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), woven, and tridirectional (3D). In addition, this test method also may be used with glass (amorphous) matrix composites with 1D, 2D, and 3D continuous fiber reinforcement. This test method does not directly address discontinuous fiber-reinforced, whisker-reinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites. It should be noted that 3D architectures with a high volume fraction of fibers in the “z” direction may be difficult to test successfully. 1.3 Values are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Additional recommendations are provided in 6.7 and Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Transthickness Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperature

BS ISO 21859:2019 精细陶瓷（先进陶瓷、先进技术陶瓷） 半导体制造设备中陶瓷元件耐等离子性的测试方法

What is ISO 21859 - Plasma resistance of ceramic components about?    ISO 21859 is an international standard on fine ceramics which covers a test method for plasma resistance of ceramic components in semiconductor manufacturing equipment.   ISO 21859 specifies a test method for plasma resistance of ceramic components in semiconductor manufacturing equipment. It is applicable to ceramic components of plasma-resistant components in dry etching chambers used in semiconductor manufacturing.   Who is ISO 21859 - Plasma resistance of ceramic components for?  ...

Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for plasma resistance of ceramic components in semiconductor manufacturing equipment

ISO 21859:2019 精细陶瓷（先进陶瓷 先进技术陶瓷） - 半导体制造设备中陶瓷部件的等离子体电阻试验方法

This document specifies a test method for plasma resistance of ceramic components in semiconductor manufacturing equipment. It is applicable to ceramic components of plasma-resistant components in dry etching chambers used in semiconductor manufacturing.

Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for plasma resistance of ceramic components in semiconductor manufacturing equipment

ISO 20501:2019 精细陶瓷（先进陶瓷 先进技术陶瓷） - 威布尔统计强度数据

This document covers the reporting of uniaxial strength data and the estimation of probability distribution parameters for advanced ceramics which fail in a brittle fashion. The failure strength of advanced ceramics is treated as a continuous random variable. Typically, a number of test specimens with well-defined geometry are brought to failure under well-defined isothermal loading conditions. The load at which each specimen fails is recorded. The resulting failure stresses are used to obtain parameter estimates associated with the underlying population distribution. This document is restricted to the assumption that the distribution underlying the failure strengths is the two-parameter Weibull distribution with size scaling. Furthermore, this document is restricted to test specimens (tensile, flexural, pressurized ring, etc.) that are primarily subjected to uniaxial stress states. Subclauses 6.4 and 6.5 outline methods of correcting for bias errors in the estimated Weibull parameters, and to calculate confidence bounds on those estimates from data sets where all failures originate from a single flaw population (i.e. a single failure mode). In samples where failures originate from multiple independent flaw populations (e.g. competing failure modes), the methods outlined in 6.4 and 6.5 for bias correction and confidence bounds are not applicable.

Fine ceramics (advanced ceramics, advanced technical ceramics) — Weibull statistics for strength data

ISO 21618:2019 精细陶瓷（先进陶瓷 先进技术陶瓷） - 通过压痕断裂（IF）法在室温下整体陶瓷的耐断裂性试验方法

This document describes a test method that covers the determination of fracture resistance of monolithic ceramics at room temperature by the indentation fracture (IF) method. This document is intended for use with dense monolithic ceramics and whisker- or particulate- reinforced ceramics which are regarded as macroscopically homogeneous. It does not include monolithic silicon nitride ceramics for bearing balls and continuous-fibre-reinforced ceramics composites. This document is for material development, material comparison, quality assurance, characterization and reliability data generation. Indentation fracture resistance, KI,IFR, as defined in this document is not to be equated with fracture toughness determined using other test methods such as KIsc and KIpb. NOTE KI,IFR is an estimate of a material’s resistance to cracking as introduced by an indenter and has correlations with wear resistance and rolling contact fatigue performance as well as machining processes, since these properties are governed by the resistance to crack extension in localized damage areas[1]-[3]. By contrast, fracture toughness properties KIsc and KIpb are intrinsic properties of a material and are relevant to macroscopic and catastrophic fracture events with long cracks rather than those phenomena caused by microscopic and successive damage accumulation associated with short cracks.

Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for fracture resistance of monolithic ceramics at room temperature by indentation fracture (IF) method

ISO 21813:2019 精细陶瓷（高级陶瓷 高级工业陶瓷）高纯钛酸钡粉末化学分析方法

This document specifies methods for the chemical analysis of fine high purity barium titanate powders used as the raw material for fine ceramics. This document stipulates the determination methods of the barium, titanium, aluminium, cadmium, calcium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, sodium, strontium, vanadium, zirconium, carbon, oxygen and nitrogen contents in high purity barium titanate powders. The barium and titanium contents, the major elements, are determined by using an acid decomposition-gravimetric method or an acid decomposition-inductively coupled plasma- optical emission spectrometry (ICP-OES) method. The aluminium, cadmium, calcium, chromium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, strontium, vanadium and zirconium contents are simultaneously determined via an acid digestion-ICP-OES method. The nitrogen content is determined by using an inert gas fusion-thermal conductivity method, while that of oxygen is determined via an inert gas fusion-IR absorption spectrometry method. Finally, the carbon content is determined using a combustion-IR absorption spectrometry method or a combustion-conductometry method.

Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of high purity barium titanate powders

ASTM C1468-19 室温下连续纤维增强高级陶瓷的横向拉伸强度的标准试验方法

Standard Test Method for Transthickness Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperature

ISO 21814:2019 精细陶瓷（先进陶瓷 先进技术陶瓷） - 氮化铝粉末化学分析方法

This document specifies methods for the chemical analysis of fine aluminium nitride powders used as the raw material for fine ceramics. This document stipulates the determination methods of the aluminium, total nitrogen, boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium, zinc, zirconium, carbon, chlorine, fluorine, and oxygen contents in aluminium nitride powders. The aluminium content is determined by using either an acid pressure decomposition- CyDTA-zinc back titration method or an acid digestion-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The total nitrogen content is determined by using an acid pressure decomposition-distillation separation-acidimetric titration method, a direct decomposition-distillation separation-acidimetric titration method, or an inert gas fusion-thermal conductivity method. The boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium and zinc contents are determined by using an acid digestion- ICP-OES method or an acid pressure decomposition-ICP-OES method. The sodium and potassium contents are determined via an acid pressure decomposition-flame emission method or an acid pressure decomposition-atomic absorption spectrometry method. The oxygen content is determined by using an inert gas fusion-IR absorption spectrometry method, while that of carbon is determined via a combustion-IR absorption spectrometry method or a combustion-conductometry method. The chlorine and fluorine contents are determined by using a pyrohydrolysation method followed by ion chromatography or spectrophotometry.

Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of aluminium nitride powders

ASTM C1425-19 高温下一维和二维连续纤维增强高级陶瓷层间剪切强度的标准试验方法

1.1 This test method addresses the uniaxial compression of a double-notched test specimen to determine interlaminar shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at elevated temperatures. Failure of the test specimen occurs by interlaminar shear between two centrally located notches machined halfway through the thickness of the test specimen and spaced a fixed distance apart on opposing faces (see Fig. 1). Test specimen preparation methods and requirements, testing modes (force or displacement control), testing rates (force rate or displacement rate), data collection, and reporting procedures are addressed. 1.2 This test method is used for testing advanced ceramic or glass matrix composites with continuous fiber reinforcement having a laminated structure such as in unidirectional (1D) or bidirectional (2D) fiber architecture (lay-ups of unidirectional plies or stacked fabric). This test method does not address composites with nonlaminated structures, such as (3D) fiber architecture or discontinuous fiber-reinforced, whiskerreinforced, or particulate-reinforced ceramics. 1.3 Values expressed in this test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are noted in 8.1 and 8.2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Interlaminar Shear Strength of 1-D and 2-D Continuous Fiber-Reinforced Advanced Ceramics at Elevated Temperatures

KS L ISO 22197-1:2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 半导体光催化材料的空气净化性能测试方法 - 第1部分:去除一氧化氮

Fine ceramics(advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconducting photocatalytic materials — Part 1: Removal of nitric oxide

KS L ISO 15733-2018(2023) 精细陶瓷（高级陶瓷、高级工业陶瓷）陶瓷复合材料在环境温度和大气压力下的力学性能拉伸性能的测定

Fine ceramics(advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties

KS L ISO 20808-2018(2023) 精细陶瓷（高级陶瓷、高级工业陶瓷）单片陶瓷摩擦磨损特性的球-盘法测定

Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of friction and wear characteristics of monolithic ceramics by ball-on-disc method

KS L ISO 20808-2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 通过圆盘法测定单片陶瓷的摩擦磨损特性

Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of friction and wear characteristics of monolithic ceramics by ball-on-disc method

KS L ISO 17562:2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 推杆技术的单片陶瓷线性热膨胀试验方法

Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for linear thermal expansion of monolithic ceramics by push-rod technique

KS L ISO 17561:2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 室温下通过声波共振的单片陶瓷弹性模量试验方法

Fine ceramics(advanced ceramics, advanced technical ceramics) — Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance

KS L ISO 15733:2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 陶瓷复合材料的机械性能在空气中的环境温度大气压力 - 拉伸性能的测定

Fine ceramics(advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties

KS L ISO 15733-2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 陶瓷复合材料的机械性能在空气中的环境温度大气压力 - 拉伸性能的测定

Fine ceramics(advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties

KS L ISO 17561-2018(2023) 精细陶瓷（高级陶瓷、高级工业陶瓷）室温下单片陶瓷弹性模量的声波共振试验方法

Fine ceramics(advanced ceramics, advanced technical ceramics) — Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance

KS L ISO 17561-2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 室温下通过声波共振的单片陶瓷弹性模量试验方法

Fine ceramics(advanced ceramics, advanced technical ceramics) — Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance

KS L ISO 17562-2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 推杆技术的单片陶瓷线性热膨胀试验方法

Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for linear thermal expansion of monolithic ceramics by push-rod technique