81.060.30 高级陶瓷 标准查询与下载

BS ISO 17168-3:2018 精细陶瓷（先进陶瓷、先进技术陶瓷） 室内照明环境下半导体光催化材料空气净化性能测试方法甲苯的去除

1   Scope This document specifies a test method for the determination of the air-purification performance, with regards to the removal of toluene, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination from indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form, and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Removal of toluene

ISO 21066:2018 精细陶瓷（先进陶瓷 先进技术陶瓷） - 通过在沉积的墨膜中还原赤藓红素对表面的光催化活性进行定性和半定量评估

This document specifies a method, the Resazurin (Rz) ink test, for the qualitative assessment of the activity of a photocatalytic surface, and its classification as below, within, or above the applicable range of the test. The method then allows for the subsequent semiquantitative evaluation of the activities of photocatalytic surfaces that are within the applicable range of the test. In all cases, artificial ultraviolet (UV) radiation is used. The test method specified is appropriate for use with all flat, smooth, photocatalytic surfaces, which are not macroporous, examples of which include: commercial photocatalytic glass, paint, tiles and awning materials. The method is not applicable to assessing the visible-light activity of photocatalytic surfaces, nor their ability to effect: air purification, water purification, self-cleaning or disinfection, although some relevant correlations have been reported[4][5].

Fine ceramics (advanced ceramics, advanced technical ceramics) — Qualitative and semiquantitative assessment of the photocatalytic activities of surfaces by the reduction of resazurin in a deposited i

ISO 17168-4:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.室内照明环境下半导体光催化材料空气净化性能的试验方法.第4部分：甲醛去除

This document specifies a test method for the determination of the air-purification performance, with regards to the removal of formaldehyde, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination from indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form, and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Part 4: Removal of formaldehyde

ISO 17168-3:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.室内照明环境下半导体光催化材料空气净化性能的试验方法.第3部分：甲苯的去除

This document specifies a test method for the determination of the air-purification performance, with regards to the removal of toluene, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination from indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form, and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Part 3: Removal of toluene

ISO 17168-1:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.室内照明环境下半导体光催化材料空气净化性能的试验方法.第1部分：一氧化氮的去除

This document specifies a test method for the determination of the air purification performance, with regards to removal of nitric oxide, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination from indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to certain test pieces that contain a large amount of adsorbent, due to unattained adsorption equilibrium. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Part 1: Removal of nitric oxide

ISO 17168-2:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.室内照明环境下半导体光催化材料空气净化性能的试验方法.第2部分：乙醛的去除

This document specifies a test method for the determination of the air-purification performance, with regards to removal of acetaldehyde, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination from indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form, and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Part 2: Removal of acetaldehyde

ISO 17168-5:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.室内照明环境下半导体光催化材料空气净化性能的试验方法.第5部分：甲硫醇的去除

This document specifies a test method for the determination of the air-purification performance, with regards to removal of methyl mercaptan, of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from semiconducting metal oxides such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination with indoor light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, which are the basic forms of materials for various applications. This document also applies to materials in honeycomb form, and to plastic or paper materials containing ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials. This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment - Part 5: Removal of methyl mercaptan

BS ISO 19629:2018 精细陶瓷（高级陶瓷、高级技术陶瓷） 陶瓷复合材料的热物理性能 闪光法测定一维热扩散率

Fine ceramics (advanced ceramics, advanced technical ceramics). Thermophysical properties of ceramic composites. Determination of unidimensional thermal diffusivity by flash method

BS ISO 21819-1:2018 精细陶瓷（高级陶瓷、高级技术陶瓷） 高负载条件下的压电特性 高温条件下的谐振反谐振方法

Fine ceramics (advanced ceramics, advanced technical ceramics). Characteristic of piezoelectric properties under high-load conditions. Resonant-antiresonant method under high-temperature conditions

BS ISO 21819-2:2018 精细陶瓷（高级陶瓷、高级技术陶瓷） 高负载条件下的压电特性 高振动水平下的电气瞬态响应方法

Fine ceramics (advanced ceramics, advanced technical ceramics). Characteristic of piezoelectric properties under high-load conditions. Electrical transient response method under high vibration levels

ASTM C1359-18 高温下用实心矩形截面试样对连续纤维增强高级陶瓷进行单调拉伸强度试验的标准试验方法

Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross Section Test Specimens at Elevated Temperatures

ASTM C1359-18e1 高温下用实心矩形截面试样对连续纤维增强高级陶瓷进行单调拉伸强度试验的标准试验方法

1.1 This test method covers the determination of tensile strength, including stress-strain behavior, under monotonic uniaxial loading of continuous fiber-reinforced advanced ceramics at elevated temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendixes. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, temperature control, temperature gradients, and data collection and reporting procedures are addressed. Tensile strength as used in this test method refers to the tensile strength obtained under monotonic uniaxial loading, where monotonic refers to a continuous nonstop test rate with no reversals from test initiation to final fracture. 1.2 This test method applies primarily to advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), and tridirectional (3D) or other multi-directional reinforcements. In addition, this test method may also be used with glass (amorphous) matrix composites with 1D, 2D, 3D, and other multi-directional continuous fiber reinforcements. This test method does not directly address discontinuous fiber-reinforced, whiskerreinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites. 1.3 The values stated in SI units are to be regarded as the standard and are in accordance with IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Refer to Section 7 for specific precautions. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross Section Test Specimens at Elevated Temperatures

ISO 21819-2:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.高负载条件下的压电特性.第2部分：高振动水平下的电瞬态响应法

This document specifies a method of measuring piezoelectric properties of piezoelectric fine ceramics and other piezoelectric devices. It applies to electrical transient response methods for evaluating the piezoelectric properties of piezoelectric fine ceramics resonators under high vibration levels.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Characteristic of piezoelectric properties under high-load conditions - Part 2: Electrical transient response method under high vibration levels

ISO 19629:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.陶瓷复合材料的热物理性能.用闪光法测定一维热扩散率

This document describes the flash method for the determination of thermal diffusivity of ceramic matrix composites with continuous fibre reinforcement. In order to conform with the unidimensional heat transfer hypothesis, the experimental conditions are defined such that the material behaves in a homogeneous manner. This involves performing tests in one symmetry axis of the composite. The method is applicable to materials which are physically and chemically stable during the measurement, and covers the range of temperature from 100 K to 2800 K. It is suitable for the measurement of thermal diffusivity values in the range 10−4 m2∙s−1 to 10−7 m2∙s−1.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Thermophysical properties of ceramic composites - Determination of unidimensional thermal diffusivity by flash method

ISO 21819-1:2018 精细陶瓷（高级陶瓷、高级工业陶瓷）.高负载条件下的压电特性.第1部分：高温条件下的谐振反谐振方法

This document specifies a method of measuring piezoelectric properties of piezoelectric fine ceramics and other piezoelectric devices under high-temperature conditions, where the electromechanical coupling coefficient is determined based on measurements of resonance/antiresonance frequencies using impedance analysers.

Fine ceramics (advanced ceramics, advanced technical ceramics) - Characteristic of piezoelectric properties under high-load conditions - Part 1: Resonant-antiresonant method under high-temperature conditions

BS ISO 21714:2018 精细陶瓷（高级陶瓷、高级技术陶瓷） 陶瓷涂层密度测定的试验方法

Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for determining density of ceramic coatings

BS ISO 21113:2018 精细陶瓷（高级陶瓷、高级技术陶瓷） 单片陶瓷薄板室温断裂韧性试验方法

Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for fracture toughness of monolithic ceramic thin plates at room temperature

ASTM C1358-18 室温下用实心矩形截面试样对连续纤维增强高级陶瓷的单调抗压强度试验的标准试验方法

1.1 This test method covers the determination of compressive strength, including stress-strain behavior, under monotonic uniaxial loading of continuous fiber-reinforced advanced ceramics at ambient temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendixes. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, and data collection and reporting procedures are addressed. Compressive strength, as used in this test method, refers to the compressive strength obtained under monotonic uniaxial loading, where monotonic refers to a continuous nonstop test rate with no reversals from test initiation to final fracture. 1.2 This test method applies primarily to advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), and tridirectional (3D) or other multi-directional reinforcements. In addition, this test method may also be used with glass (amorphous) matrix composites with 1D, 2D, 3D, and other multi-directional continuous fiber reinforcements. This test method does not directly address discontinuous fiber-reinforced, whiskerreinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites. 1.3 The values stated in SI units are to be regarded as the standard and are in accordance with IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Refer to Section 7 for specific precautions. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Monotonic Compressive Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross Section Test Specimens at Ambient Temperatures

ASTM C1341-13(2018) 连续纤维增强高级陶瓷复合材料弯曲性能的标准试验方法

1.1 This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes. Three test geometries are described as follows: 1.1.1 Test Geometry I—A three-point loading system utilizing center point force application on a simply supported beam. 1.1.2 Test Geometry IIA—A four-point loading system utilizing two force application points equally spaced from their adjacent support points, with a distance between force application points of one-half of the support span. 1.1.3 Test Geometry IIB—A four-point loading system utilizing two force application points equally spaced from their adjacent support points, with a distance between force application points of one-third of the support span. 1.2 This test method applies primarily to all advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), tridirectional (3D), and other continuous fiber architectures. In addition, this test method may also be used with glass (amorphous) matrix composites with continuous fiber reinforcement. However, flexural strength cannot be determined for those materials that do not break or fail by tension or compression in the outer fibers. This test method does not directly address discontinuous fiber-reinforced, whisker-reinforced, or particulate-reinforced ceramics. Those types of ceramic matrix composites are better tested in flexure using Test Methods C1161 and C1211. 1.3 Tests can be performed at ambient temperatures or at elevated temperatures. At elevated temperatures, a suitable furnace is necessary for heating and holding the test specimens at the desired testing temperatures. 1.4 This test method includes the following: Section Scope 1 Referenced Documents 2 Terminology 3 Summary of Test Method 4 Significance and Use 5 Interferences 6 Apparatus 7 Precautionary Statement 8 Test Specimens 9 Procedures 10 Calculation of Results 11 Report 12 Precision and Bias 13 Keywords 14 References CFCC Surface Condition and Finishing Annex A1 Conditions and Issues in Hot Loading of Test Specimens into Furnaces Annex A2 Toe Compensation on Stress-Strain Curves Annex A3 Corrections for Thermal Expansion in Flexural Equations Annex A4 Example of Test Report Appendix X1 1.5 The values stated in SI units are to be regarded as the standard in accordance with IEEE/ASTM SI 10. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flexural Properties of Continuous Fiber-Reinforced Advanced Ceramic Composites

ISO 21113:2018 精细陶瓷(高级陶瓷、高级技术陶瓷).室温下整体陶瓷薄板断裂韧性的试验方法

This document describes a test method for the determination of the fracture toughness of monolithic ceramic thin plates at room temperature by the single-edge precracked plate method or the single-edge V-notch plate method. This document is intended for use with monolithic ceramics and whisker- or particulate-reinforced ceramics which are regarded as macroscopically homogeneous. It does not include continuous-fibrereinforced ceramics composites. This document is applicable to ceramic thin plates with a thickness of 0,2 mm to

Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramic thin plates at room temperature