83.040.20 橡胶合成配料 标准查询与下载

GB/T 13021-1991 聚乙烯管材和管件炭黑含量的测定(热失重法)

本标准规定了聚乙烯管材和管件炭黑含量的测定方法。 本标准适用于聚乙烯管材和管件，也适用于聚烯烃管材和管件及制造管材和管件所用原料的炭黑含量的测定。

Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis

GB/T 12827-1991 标准参比乙炔炭黑及鉴定方法

本标准规定了1号标准参比乙炔炭黑（用符号SRAB1表示）主要物化性能的标准值、生产的质量控制要求及测试其均匀性的标准方法。 本标准适用于标准参比乙炔炭黑及其鉴定，还适用于校正试验仪器。

Standard reference acetylene black and standard practice for evaluation

GB/T 11409.8-1989 橡胶防老剂、硫化促进剂粘度的测定方法 旋转粘度计法

本标准规定了用旋转粘度计测定试样动力粘度的方法。 本标准适用于液体橡胶防老剂、硫化促进剂的粘度测定。

Test method of viscosity for rubber antiager and vulcanizing accelerators--Rotational viscometer method

GB/T 11409.7-1989 橡胶防老剂、硫化促进剂灰分的测定方法

本标准规定了采用高温灼烧法测定橡胶防老剂、硫化促进剂的灰分。 本标准适用于橡胶防老剂、硫化促进剂灰分的测定。

Test method of ash for rubber antiager and vulcanizing accelerators

GB/T 11409.3-1989 橡胶防老剂、硫化促进剂软化点的测定方法

本标准规定了用环球法测定试样的软化点。 本标准适用于橡胶防老剂、硫化促进剂软化点的测定。

Test method of softening point for rubber antiager and vulcanizing accelerators

GB 8829-1988 硫化促进剂NOBS(N-氧二乙撑-2-苯骈噻唑次磺酰胺)

Vulcanization accelerator NOBS (N-oxydiethylene-2-benzothiazyl sulfenamide)

GB/T 3780.16-1983 炭黑单个粒子压碎强度的测定

Carbon black--Determination of individual pellet crush strength

GB/T 3780.13-1983 炭黑(粒状)倾注密度的测定

Carbon black(pelletized)--Determination of pour density

T/QGCML 4296-2024 多腔橡皮筋

本文件规定了多腔橡皮筋的术语定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于多腔橡皮筋的生产和检验。

Multi-chamber rubber band

ASTM D8371-24 炭黑中痕量金属含量分析的标准试验方法

1.1 This test method covers the determination of metal content in carbon black with ICP-OES or ICP-MS after adequate digestion. See 3.1.5 – 3.1.7 for definitions. 1.2 The concentration ranges covered by these test methods are determined by the sensitivity of the instruments, the amount of sample taken for analysis and the dilution volume. 1.3 Detection limits, sensitivity and optimum ranges of the metals will vary with the matrices and model of spectrometer. 1.4 Elements present at concentrations above the linear response range of the calibration curve can be determined with additional appropriate dilutions. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Trace Metal Content Analysis in Carbon Black

GSO ISO 28641:2024 橡胶混合料 有机化学品 通用试验方法

This document specifies sampling and test methods for the determination of the general characteristics of organic chemicals such as accelerators, antidegradants (including wax) and vulcanizing agents (excluding peroxides).

Rubber compounding ingredients — Organic chemicals — General test methods

ASTM D5857-17(2024) 使用ISO协议和方法的聚丙烯注射和挤出材料的标准规范

Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

ASTM D1510-24 炭黑的标准试验方法碘吸附值

1.1 This test method covers the determination of the iodine adsorption number of carbon black. 1.1.1 Method A is the original test method for this determination and Method B is an alternate test method using automated sample processing and analysis. 1.2 The iodine adsorption number of carbon black has been shown to decrease with sample aging. Iodine Number reference materials have been produced that exhibit stable iodine number upon aging. One or more of these reference materials are recommended for daily monitoring (x-charts) to ensure that the results are within the control limits of the individual reference material. Use all Iodine Number reference materials from a set for standardization of iodine testing (see Section 8) when target values cannot be obtained. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon Black—Iodine Adsorption Number

ASTM D3265-24 炭黑着色强度的标准试验方法

1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon Black—Tint Strength

T/FSI 131-2023 气相二氧化硅羟基含量测定方法-TGA

本文件规定了气相二氧化硅（俗称气相法白炭黑）硅羟基测试的试验方法，包括原理、仪器、步骤的相关规定。 本文件适用于热重分析法测试未改性的气相二氧化硅的总羟基含量。 本文件不适合在测试温度下有挥发性物质的二氧化硅。

Determination method for hydroxyl content of fumed silica-TGA

KS M ISO 28641-2023 橡胶配合料有机化学品通用试验方法

Rubber compounding ingredients — Organic chemicals — General test methods

KS M ISO 11236-2023 橡胶配合料对苯二胺抗降解剂试验方法

Rubber compounding ingredients — p-Phenylenediamine antidegradants(PPDs) — Test methods

KS M ISO 5435-2023 橡胶配合料炭黑着色强度的测定

Rubber compounding ingredients — Carbon black — Determination of tinting strength

ASTM D7772-15(2023) 炭黑提取物的标准试验方法——环己烷提取物的吸收率

Standard Test Method for Carbon Black Extractables – Absorbance of Cyclohexane Extract

ASTM D1618-23 炭黑提取物的标准试验方法甲苯提取物的透射率

Standard Test Method for Carbon Black Extractables—Transmittance of Toluene Extract