83.040.30 塑料的辅料和添加剂 标准查询与下载
共找到 299 条与 塑料的辅料和添加剂 相关的标准，共 20 页
This part of this European standard provides an introduction to the various parts of this European Standard which describe methods for dispersing pigments and extenders in plastics materials in order to determine their dispersion characteristics and colouristic properties.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1: General introduction
- ICS
- 83.040.30
- CCS
- 发布
- 2003-05-09
- 实施
- 2003-03-25
This part of EN specifies a method of determining in polyethylene the colouristic properties of a test pigment relative to a standard, and the ease of dispersion of pigments from the differences in colour strength on dispersing colouring materials under various conditions.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling
- ICS
- 83.040.30
- CCS
- 发布
- 2003-05-09
- 实施
- 2003-03-25
This part of this European Standard provides an introduction to the various parts of this European Standard which describe methods for dispersing pigments and extenders in plastics materials in order to determine their dispersion characteristics and colouristic properties.Methods of assessing dispersion characteristics are described in the subsequent parts of this European Standard.The various procedures described permit comparison to be made between similar pigments (for example between a test sample and an agreed reference pigment). The results provide an indication of relative dispersibility under practical conditions of use, provided that the test procedure and plastics material selected are appropriate.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1: General introduction
- ICS
- 83.040.30
- CCS
- 发布
- 2003-02-21
- 实施
This part of this European Standard provides an introduction to the various parts of this European Standard which describe methods for dispersing pigments and extenders in plastics materials in order to determine their dispersion characteristics and colouristic properties. Methods of assessing dispersion characteristics are described in the subsequent parts of this European Standard. The various procedures described permit comparison to be made between similar pigments (for example between a test sample and an agreed reference pigment). The results provide an indication of relative dispersibility under practical conditions of use, provided that the test procedure and plastics material selected are appropriate.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - General introduction
- ICS
- 83.040.30
- CCS
- G54
- 发布
- 2003-02-21
- 实施
- 2003-02-21
This part of this European Standard specifies a method of determining the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DHPVC-P of pigments from the differences in colour strength on dispersing colouring materials under various conditions in plasticized polyvinyl chloride (PVC-P) compounds. The method is appropriate for use with organic and inorganic black and colour pigments and for pigment preparations. The ease of dispersion determined in this way is valid only for the dispersion equipment, dispersion conditions and dispersion medium being used. The use of test conditions differing from those specified may give different results; this applies both to the absolute magnitude and to the relation between values of the ease of dispersion of various pigments. The subscript DHPVC-P is therefore used to designate the value obtained as specified in this part of this European Standard. The principle of this standard may also be used for routine quality control purposes by reference to the photometric data generated from the sheets milled at 130 ℃. For quality control purposes, the ratio of pigment to TiO2 may be agreed between the interested parties. Ratios of 1:10 for organic pigments and 0,2 to 0,5:1 for inorganic pigments are suggested as convenient and widely used standard ratios. Annex A is informative and gives a description of a suitable basic compound.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion in plasticized polyvinyl chloride by two-roll milling
- ICS
- 83.040.30
- CCS
- G54
- 发布
- 2003-02-21
- 实施
- 2003-02-21
This part of this European Standard specifies a method of determining in polyethylene (PE) the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DHPE of pigments from the differences in colour strength on dispersing colouring materials under various conditions.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling
- ICS
- 83.040.30
- CCS
- 发布
- 2003-02-21
- 实施
This part of this European Standard specifies a method of determiningThe colouristic properties of a test pigment relative to a standard, andThe ease of dispersion DHPV}_P of pigments fromThe differences in colour strength on dispersing colouring materials under various conditions in plasticized polyvinyl chloride (PVC-P) compounds.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 2: Determination of colouristic properties and ease of dispersion in plasticized polyvinylchloride by two-roll milling
- ICS
- 83.040.30
- CCS
- 发布
- 2003-02-21
- 实施
This part of this European Standard specifies a method of determining in polyethylene (PE) the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DHPE of pigments from the differences in colour strength on dispersing colouring materials under various conditions. Method A is appropriate for use with organic powder pigments and carbon black pigments in powder form, many of which are subject to compaction (reagglomeration under pressure), for inorganic pigments in powder form and for pigment preparations in powder or flake form. Method B is appropriate for testing pigments and pigment preparations in granular form and for inorganic pigments in any form. The ease of dispersion determined in this way is valid only for the dispersion equipment, dispersion conditions and dispersion medium being used. The use of test conditions differing from those specified may give different results; this applies both to the absolute magnitude and to the relation between values of the ease of dispersion of various pigments. The subscript DHPE is therefore used to designate the value obtained as specified in this part of this European Standard.
Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling
- ICS
- 83.040.30
- CCS
- G54
- 发布
- 2003-02-21
- 实施
- 2003-02-21
Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 3: Determination by oven test
- ICS
- 83.040.30
- CCS
- 发布
- 2002-10-14
- 实施
- 2002-10-14
Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 4: Determination by two-roll milling
- ICS
- 83.040.30
- CCS
- 发布
- 2002-10-14
- 实施
- 2002-10-14
Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 2: Determination by injection moulding
- ICS
- 83.040.30
- CCS
- 发布
- 2002-10-14
- 实施
- 2002-10-14
Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 1: General introduction
- ICS
- 83.040.30
- CCS
- 发布
- 2002-10-14
- 实施
- 2002-10-14
This International Standard specifies methods used to measure the water content of polyols employed as polyurethane raw materials. Method A is a manual amperometric method which has been included to better define the principles of the Karl Fischer measurement. Amperometric methods are applicable to a wide range of polyols, including those which have enough colour to obscure a visual end-point. Method B includes an automated amperometric procedure and an automated coulometric procedure. The coulometric procedure is an absolute method that does not require calibration and gives improved sensitivity compared with amperometric methods.
Plastics - Polyols for use in the production of polyurethane - Determination of water content
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2002-07-29
- 实施
- 2002-07-29
This International Standard specifies a microtitration method to measure the degree of unsaturation in polyether polyols used in the production of polyurethanes. It is based on the reaction of mercuric acetate with double bonds in the polyol. It does not apply to compounds in which the unsaturation is conjugated with carbonyl, carboxyl or nitrile groups. The product being measured must be essentially dry and free of inorganic salts, especially halides.
Plastics - Polyols for use in the production of polyurethane - Determination of degree of unsaturation by microtitration
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2002-07-29
- 实施
- 2002-07-29
This International Standard specifies methods used to measure the water content of polyols employed as polyurethane raw materials. Method A is a manual amperometric method which has been included to better define the principles of the Karl Fischer measurement. Amperometric methods are applicable to a wide range of polyols, including those which have enough colour to obscure a visual end-point. Method B includes an automated amperometric procedure and an automated coulometric procedure. The coulometric procedure is an absolute method that does not require calibration and gives improved sensitivity compared with amperometric methods.
Plastics - Polyols for use in the production of polyurethane - Determination of water content
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2002-06
- 实施
This International Standard specifies a microtitration method to measure the degree of unsaturation in polyether polyols used in the production of polyurethanes. It is based on the reaction of mercuric acetate with double bonds in the polyol. It does not apply to compounds in which the unsaturation is conjugated with carbonyl, carboxyl or nitrile groups. The product being measured must be essentially dry and free of inorganic salts, especially halides.
Plastics - Polyols for use in the production of polyurethane - Determination of degree of unsaturation by microtitration
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2002-05
- 实施
This test method covers the determination of the relative volatility of plasticizers, or volatile contaminants, or both, at elevated temperatures. The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-There are no ISO standards covering the primary subject of this test method.
Test Method for Weight Loss of Plasticizers on Heating (X-15-373-1) (08.02)
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2001
- 实施
- 2001-11-10
This practice defines the conditions for the exposure and qualitative evaluation of poly(vinyl chloride) (PVC) compounds for plasticizer compatibility under humid conditions. Change in appearance is used for judging compatibility. The text of this practice references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice. The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-There are no ISO standards covering the primary subject of this practice.
Practice for Testing Plasticizer Compatibility in Poly(Vinyl Chloride) (PVC) Compounds under Humid Conditions (08.02)
- ICS
- 83.040.30
- CCS
- G31
- 发布
- 2001
- 实施
- 2001-11-10
Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:1996)
- ICS
- 83.040.30
- CCS
- 发布
- 2000-12-15
- 实施
- 2000-12-15
Fillers and reinforcing materials
- ICS
- 83.040.30
- CCS
- 发布
- 2000-10-15
- 实施
- 2000-10-15
