83.060 (Rubber) 标准查询与下载

ASTM D3182-89(2001) 橡胶的标准规程.混合标准化合物和制备标准硫化薄板用材料、设备和方法

1.1 This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing. It also specifies the mixing equipment, general mixing procedures, vulcanization equipment and procedures. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statements, see 5.5.

Standard Practice for Rubber8212;Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

ASTM D3182-89(2001)e1 橡胶的标准规程.混合标准化合物和制备标准硫化薄板用材料、设备和方法

1.1 This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing. It also specifies the mixing equipment, general mixing procedures, vulcanization equipment and procedures.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statements, see .

Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

ASTM D991-89(2005) 橡胶特性.导电橡胶及抗静电橡胶制品的体电阻系数测试方法

The electrical behavior of rubber products used in particular applications is important for a variety of reasons such as safety, static changes, current transmission, etc. This test method is useful in predicting the behavior of such rubber products.1.1 This test method covers the determination of volume resistivity of rubbers used in electrically conductive and antistatic products.1.2 This test method assumes that the surface conductivity is negligible compared with the conductivity through the specimen.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property-Volume Resistivity Of Electrically Conductive and Antistatic Products

ASTM D3182-89(2006) 橡胶的标准规程.混合标准化合物和制备标准硫化薄板用材料、设备和方法

1.1 This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing. It also specifies the mixing equipment, general mixing procedures, vulcanization equipment and procedures.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see .

Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

ASTM D991-89(2000)e1 橡胶性能的标准试验方法&x2014；导电和抗静电产品的体积电阻率

1.1 This test method covers the determination of volume resistivity of rubbers used in electrically conductive and antistatic products. 1.2 This test method assumes that the surface conductivity is negligible compared to the conductivity through the specimen. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property-Volume Resistivity Of Electrically Conductive and Antistatic Products

ASTM D4572-89(2005) 橡胶加工用化学药品的试验方法-硫磺的湿法筛选分析

This test method is used to evaluate sulfur for suitability as a rubber vulcanizing agent. Sulfur particles must be significantly small enough to dissolve in rubber during cure and produce a uniform network of cross-links. This test method is used as a quality control method to ensure that no excessively large sulfur particles are present and to see if the product follows a typical pattern of size distribution. This procedure is necessary when problems of the sulfur caking occur with the use of the dry sieving procedure for particle size.1.1 This test method covers the evaluation of the particle size distribution of the coarse fraction of sulfur. It is limited to the measurement of those particles greater than 45 m (No. 325 sieve).This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Chemicals-Wet Sieve Analysis of Sulfur

ASTM D991-89(2010) 橡胶特性标准试验方法.导电及抗静电制品体积电阻系数

The electrical behavior of rubber products used in particular applications is important for a variety of reasons such as safety, static changes, current transmission, etc. This test method is useful in predicting the behavior of such rubber products.1.1 This test method covers the determination of volume resistivity of rubbers used in electrically conductive and antistatic products. 1.2 This test method assumes that the surface conductivity is negligible compared with the conductivity through the specimen. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property-Volume Resistivity Of Electrically Conductive and Antistatic Products

ASTM D925-88(2000) 橡胶性能的标准试验方法&x2014；表面染色（接触、迁移和扩散）

1.1 These test methods describe techniques to evaluate three types of staining or discoloration that rubber may cause when in contact with or in proximity to another surface that may be light colored. 1.2 The test methods also describe how to qualitatively evaluate the degree of staining or discoloration produced in such situations. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber Property-Staining of Surfaces (Contact, Migration, and Diffusion)

ASTM D1415-88(1999) 橡胶特性的标准试验方法.国际硬度

1.1 This test method describes a procedure for measuring the hardness of rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with the rubber: (1 ) with a small initial force and (2 ) with a much larger final force. The differential penetration is taken at a specified time and converted to a hardness scale value. 1.2 This test method is identical in substance with ISO48. 1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property-International Hardness

ASTM D4570-86(1998) 橡胶化学品的标准试验方法通过筛分（干）测定硫的粒度

1.1 This test method covers the particle size measurement of the coarse fraction of ground sulfurs. It is limited to measurement of particles greater than 45 [mu]m (No. 325 sieve). If the sulfur is very fine and the screens become plugged by the caking of the sulfur, it may be necessary to use a wet sieve procedure instead. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Chemicals-Determination of Particle Size of Sulfur by Sieving (Dry)

ASTM D1456-86(2005) 橡胶特性的测试方法.特定应力下的延伸

This test method is useful for determining the variability in material and the influence of parameters affecting the stress-strain properties of rubber vulcanizates, for example, temperature, relative humidity, preconditioning of rubber, and so forth. This test method is particularly useful for the evaluation of compounding materials used for reference purposes.1.1 This test method covers determination of the elongation of soft vulcanized rubber compounds under a specified stress.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Elongation at Specific Stress

ASTM D1460-86(2010) 橡胶性能的标准试验方法&8212.液体浸没期间的长度变化

This test method gives the rubber technologist two means to evaluate the effect of liquids on rubber vulcanizates or rubbery materials. Volatile, nonvolatile, and other liquids that require pressure to maintain a liquid state may be used. Data obtained on rubbery materials exposed to liquids by this method may be used to predict their behavior in applications involving similar exposure. These changes in length have been found to be useful for specifications but do not necessarily indicate changes for design purposes.1.1 This test method covers a technique to measure the effect of immersion liquids on rubber vulcanizates or rubbery materials. Change in specimen geometry and dimensions are observed through the transparent walls of the tube containing the specimen immersed in the liquid. Although it may be employed with any liquid, it is especially applicable to liquids that are so volatile that they must be maintained under pressure during the period of immersion. 1.2 This test method differs from Test Method D471 in that volume changes are approximated from observed dimensional changes rather than being calculated directly. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Change in Length During Liquid Immersion

ASTM D1460-86(2005) 橡胶性能的测试方法.液体浸没期间的长度变化

This test method gives the rubber technologist two means to evaluate the effect of liquids on rubber vulcanizates or rubbery materials. Volatile, nonvolatile, and other liquids that require pressure to maintain a liquid state may be used. Data obtained on rubbery materials exposed to liquids by this method may be used to predict their behavior in applications involving similar exposure. These changes in length have been found to be useful for specifications but do not necessarily indicate changes for design purposes.1.1 This test method covers a technique to measure the effect of immersion liquids on rubber vulcanizates or rubbery materials. Change in specimen geometry and dimensions are observed through the transparent walls of the tube containing the specimen immersed in the liquid. Although it may be employed with any liquid, it is especially applicable to liquids that are so volatile that they must be maintained under pressure during the period of immersion. 1.2 This test method differs from Test Method D 471, in that volume changes are approximated from observed dimensional changes rather than being calculated directly. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Change in Length During Liquid Immersion

ASTM D1456-86(2001) 橡胶特性的测试方法.特定应力下的延伸

1.1 This test method covers determination of the elongation of soft vulcanized rubber compounds under a specified stress. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Elongation at Specific Stress

ASTM D1456-86(2010) 橡胶&8212特性的标准试验方法.特定应力下的延伸

This test method is useful for determining the variability in material and the influence of parameters affecting the stress-strain properties of rubber vulcanizates, for example, temperature, relative humidity, preconditioning of rubber, and so forth. This test method is particularly useful for the evaluation of compounding materials used for reference purposes.1.1 This test method covers determination of the elongation of soft vulcanized rubber compounds under a specified stress. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Elongation at Specific Stress

ASTM D1460-86(2001) 橡胶性能的测试方法.液体浸没期间的长度变化

1.1 This test method covers a technique to measure the effect of immersion liquids on rubber vulcanizates or rubbery materials. Change in specimen geometry and dimensions are observed through the transparent walls of the tube containing the specimen immersed in the liquid. Although it may be employed with any liquid, it is especially applicable to liquids that are so volatile that they must be maintained under pressure during the period of immersion. 1.2 This test method differs from Test Method D 471, in that volume changes are approximated from observed dimensional changes rather than being calculated directly. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Change in Length During Liquid Immersion

ASTM D3896-85(2001) 来自合成源的橡胶的标准实践 - 取样

1.1 This practice covers a uniform procedure for sampling lots of solid synthetic rubbers. Raw synthetic rubber generally is marketed in bales or packages of various sizes. 1.2 A procedure for determining the acceptability of lots of synthetic rubber is given. This procedure is based on a variables sampling plan. 1.3 The sample size is based on the assumption of a visually homogeneous material. If obvious heterogeneity exists, the number of samples shall be increased. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rubber From Synthetic Sources-Sampling

ASTM D3855-84(2004) 橡胶绳因洗涤液浸渍变质的试验方法

Rubber threads or garments containing rubber threads are very often subjected to washing treatments that differ considerably in the composition and temperature of the washing solution used. Information on the composition of commercial detergents used is not readily available, and the same brand name may contain variations in composition.1.1 This test method covers the measurement of the relative deterioration resistance of bare rubber threads subjected to a standard washing solution when they are dried at room temperature and heat aged.1.2 The results obtained by this test method are only comparative since it may not be possible to absolutely correlate such results with actual service life of the threads or of an article containing the threads.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Thread-Deterioration Due to Standard Washing Solution Treatment

ASTM D3855-84(2000) 橡胶绳因洗涤液浸渍变质的标准试验方法

1.1 This test method is used to measure the relative deterioration resistance of bare rubber threads subjected to a standard washing solution when they are dried at room temperature and heat aged. 1.2 The results obtained by this test method are only comparative since it may not be possible to absolutely correlate such results with actual service life of the threads or of an article containing the threads. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Thread-Deterioration Due to Standard Washing Solution Treatment

ASTM D3183-84(1998) 橡胶标准操作规程&x2014；从产品中制备用于试验目的的试件

1.1 This practice describes methods for the preparation of pieces of a rubber vulcanizate that is not in the form of sheet. Such pieces are used as a source from which specimens are obtained for testing. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rubber-Preparation of Pieces for Test Purposes from Products