83.080.20 热塑性塑料 标准查询与下载

T/YNZJ 004-2022 食品包装用复合膜、袋

本文件规定了食品包装用复合膜、袋的产品分类和规格、原辅材料食品安全要求、生产安全规范、要求、试验方法、检验规则及标志、包装、运输、贮存。 本文件适用于干法复合、挤出复合或无溶剂复合等工艺生产的食品包装用复合膜、袋（以下简称“膜（袋）”）。

Composite film and bag for food packaging

T/YNZJ 006-2022 聚烯烃塑料瓶

本文件规定了聚烯烃塑料瓶的产品分类、生产卫生规范、原辅材料食品安全要求、要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于以聚乙烯树脂或聚丙烯树脂为主要原料，经挤吹或注吹等工艺加工成型的聚烯烃塑料瓶。

polyolefin plastic bottle

T/YNZJ 005-2022 聚对苯二甲酸乙二醇酯（PET）桶（瓶）

本文件规定了聚对苯二甲酸乙二醇酯(PET)桶（瓶）系列产品的产品分类、生产卫生规范、原辅材料食品安全要求、要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于以聚对苯二甲酸乙二醇酯（PET）树脂为主要原料，采用注塑、拉伸、吹塑一步法或二步法工艺生产的，在常温常压下使用的聚对苯二甲酸乙二醇酯（PET）桶（瓶）。

Polyethylene terephthalate (PET) barrel (bottle)

ISO 16396-2:2022 塑料.聚酰胺模塑和挤压材料.第2部分:试样制备和性能测定

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyamide moulding and extrusion materials. It gives the requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing. This document specifies procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. It lists the properties and test methods that are suitable and necessary to characterize polyamide moulding and extrusion materials. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this document, as are the designatory properties viscosity number and tensile modulus given in

Plastics — Polyamide (PA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties

T/ZZB 2783-2022 路面标线涂料用氢化石油树脂

本文件规定了路面标线涂料用氢化石油树脂的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于以乙烯副产碳九为原料，经聚合、加氢及改性工艺制得的路面标线涂料用氢化石油树脂。

Hydrogenated petroleum resin for pavement marking paint

ISO 1133-1:2022 塑料.热塑性塑料熔体质量流率（MFR）和熔体体积流率（MVR）的测定.第1部分:标准方法

This document specifies two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic materials under specified conditions of temperature and load. Procedure A is a mass-measurement method. Procedure B is a displacement-measurement method. Normally, the test conditions for measurement of melt flow rate are specified in the material standard with a reference to this document. The test conditions normally used for thermoplastics are listed in Annex A. The MVR is particularly useful when comparing materials of different filler content and when comparing filled with unfilled thermoplastics. The MFR can be determined from MVR measurements, or vice versa, provided the melt density at the test temperature is known. This document is also possibly applicable to thermoplastics for which the rheological behaviour is affected during the measurement by phenomena such as hydrolysis (chain scission), condensation and cross-linking, but only if the effect is limited in extent and only if the repeatability and reproducibility are within an acceptable range. For materials which show significantly affected rheological behaviour during testing, this document is not appropriate. In such cases, ISO 1133-2 applies. NOTE The rates of shear in these methods are much smaller than those used under normal conditions of processing, and therefore it is possible that data obtained by these methods for various thermoplastics will not always correlate with their behaviour during processing. Both methods are used primarily in quality control.

Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method

T/CIPR 058-2022 纸尿裤抗菌包装袋生产技术规范

本技术从吹膜、电晕、印刷到制袋工序实行一体化运行，在吹膜过程通过加入崇高纳米公司提供的纳米有机无机复合抗菌母粒产品，得到具有抗菌性能的薄膜，经过电晕处理后，在印刷工序中，在油墨中加入崇高纳米公司的纳米有机无机复合抗菌剂PE-G2，使印刷图案表面具有优异抗菌性能。在经过后续制袋工序，这样包装袋外部包括印刷图案表面都具有抗菌自洁功能，不管是纸尿裤生产厂家进行包装时，还是在消费者进行使用时，人手频繁触摸过程中最大程度保证了卫生安全洁净程度；包装袋内层与纸尿裤直接接触，也具有抗菌性能，保证了纸尿裤储存环境的洁净卫生。 

Technical specifications for the production of antibacterial packaging bags of diapers

T/CIPR 057-2022 纸尿裤抗菌包装袋

本文件规定了纸尿裤抗菌包装袋技术规范，包含术语和定义、技术要求、技术指标、一般要求，并描述了技术目标和技术效益。 抗菌材料组份 4.1.1  抗菌内层包括如下重量百分数的组分：LLDPE 50％～55％、LDPE 18％～23％、m-PE 20％～30％、PPA 0.1％～0.5％、开口剂0.1％～0.5％、抗菌母粒1％～5％。 4.1.2  中间层包括如下重量百分数的组分：LLDPE 60％～70％、LDPE 15％～20％、m-PE15％～20％。 4.1.3  抗菌外层包括如下重量百分数的组分：LLDPE 40％～48％、LDPE 12％～16％、m-PE 33％～40％、PPA0.1％～0.5％、EVA 1％～5％、开口剂0.1％～0.5％、抗菌母粒1％～3％。 4.2  抗菌材料  抗菌母粒的型号为PE-G2。

Diapers Antibacterial Packaging Bag

KS M ISO 19063-1-2022 塑料ㅡ耐冲击聚苯乙烯（PS-I）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Impact-resistant polystyrene (PS-I) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 17855-2-2022 塑料ㅡ聚乙烯（PE）成型和挤出材料ㅡ第2部分：试样的制备和性能测定

Plastics ㅡ Polyethylene (PE) moulding and extrusion materials ㅡ Part 2: Preparation of test specimens and determination of properties

KS M ISO 19069-1-2022 塑料ㅡ聚丙烯（PP）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Polypropylene (PP) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 19062-1-2022 塑料ㅡ丙烯腈-丁二烯-苯乙烯（ABS）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 17855-1-2022 塑料ㅡ聚乙烯（PE）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Polyethylene (PE) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 19064-1-2022 塑料ㅡ苯乙烯/丙烯腈（SAN）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Styrene/acrylonitrile (SAN) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 19066-1-2022 塑料ㅡ甲基丙烯酸甲酯-丙烯腈-丁二烯-苯乙烯（MABS）成型和挤出材料ㅡ第1部分：命名系统和规格基础

Plastics ㅡ Methyl methacrylate-acrylonitrile- butadiene-styrene (MABS) moulding and extrusion materials ㅡ Part 1: Designation system and basis for specifications

KS M ISO 19069-2-2022 塑料ㅡ聚丙烯（PP）成型和挤出材料ㅡ第2部分：试样的制备和性能测定

Plastics ㅡ Polypropylene (PP) moulding and extrusion materials ㅡ Part 2: Preparation of test specimens and determination of properties

KS M 3802-2022 地板覆盖-PVC

Floorcovering — PVC

T/GDPIA 46-2022 塑料 食品接触用全生物降解吸管专用料

1  范围 本文件规定了食品接触用全生物降解吸管材料的术语和定义、要求、试验方法、检验规则、标志、包装、运输、贮存和贮存期。 本文件适用于由一种或一种以上具备全生物降解能力的聚酯树脂经由改性制备的，专用于生产吸管的全生物降解塑料。 2  规范性引用文件 3  术语和定义 4  要求 5  试验方法 6  检验规则 7  标志 8  包装、运输与贮存

Plastics Completely biodegradable food-contact material for straw

GSO ASTM D1238:2022 用挤出塑性计测定热塑性塑料熔体流动速率的标准测试方法

1.1 This test method covers the determination of the rate of extrusion of molten thermoplastic resins using an extrusion plastometer. After a specified preheating time, resin is extruded through a die with a specified length and orifice diameter under prescribed conditions of temperature, load, and piston position in the barrel. Four procedures are described. Comparable results have been obtained by these procedures in interlaboratory round-robin measurements of several materials and are described in Section 15. 1.2 Procedure A is used to determine the melt flow rate (MFR) of a thermoplastic material. The units of measure are grams of material/10 minutes (g/10 min). It is based on the measurement of the mass of material that extrudes from the die over a given period of time. It is generally used for materials having melt flow rates that fall between 0.15 and 50 g/10 min (see Note 1). 1.3 Procedure B is an automatically timed measurement used to determine the melt flow rate (MFR) as well as the melt volume rate (MVR) of thermoplastic materials. MFR measurements made with Procedure B are reported in g/10 minutes. MVR measurements are reported in cubic centimetres/ten minutes (cm3 /10 min). Procedure B measurements are based on the determination of the volume of material extruded from the die over a given period of time. The volume is converted to a mass measurement by multiplying the result by the melt density value for the material (see Note 2). Procedure B is generally used with materials having melt flow rates from 0.50 to 1500 g/10 min.

Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

GSO 2691:2022 聚丙烯或聚乙烯制成的食品容器多次使用

This GSO standard is concerned with the general requirements and characteristics of Polypropylene (PP) or Polyethylene (PE)food packaging containers for multi-use, formed by plastic processing, for food packing.

Food containers made of polypropylene or polyethylene are used several times