83.080.20 热塑性塑料 标准查询与下载

T/SHPTA 014.1-2021 额定电压6kV到35kV电力电缆用改性聚丙烯绝缘及屏蔽材料 第1部分：额定电压6kV到35kV电力电缆用改性聚丙烯绝缘料

本文件给出了额定电压6kV到35kV电力电缆用改性聚丙烯绝缘料技术要求、试验方法、检验规则、包装、标志、运输和贮存等的规定。

Modified polypropylene insulating compounds and semi-conductive shieding compounds for power cables of rated voltages from 6kV up to 35kV Part 1 : Modified polypropylene insulating compounds for power cables of rated voltages from 6kV up to 35kV

T/SHPTA 014.2-2021 额定电压6kV到35kV电力电缆用改性聚丙烯绝缘料及半导电屏蔽料 第2部分：额定电压6kV到35kV聚丙烯绝缘电力电缆用半导电屏蔽料

本文件给出了额定电压6到35kV聚丙烯绝缘电力电缆用半导电屏蔽料的技术要求、试验方法、检验规则、包装、标志、运输和贮存等的规定。

Modified polypropylene insulating compounds and semi-conductive shielding compounds for power cables of rated voltages from 6kV up to 35kV – Part 2 : Semi-conductive shielding compounds for polypropylene insulating power cables of rated voltages fro

T/WJDGC 0001-2021 食品包装用塑料瓶

3　分类 制品按用途不同分类为：花生油瓶、调和油瓶。 4　技术要求 4.1 原辅料 原辅料应符合相应的国家标准、行业标准和相关规定。食品用树脂原材料不得使用回收料。食品用树脂使用的添加剂应符合GB 9685要求。 4.2 外观 制品不应有明显变形、裂纹、飞边、气孔、凹坑和塑化不良现象。  4.3 容量 实际容量应大于或等于公称容量。 4.4高度差 应符合表1的规定。 表1 项目　指标 高度（H）＜160mm　±1.5 160mm≤高度（H）≤250mm　±2.0 高度（H）＞250mm　±3.0 4.5 密封性能 密封性能无渗漏。 4.6 物理机械性能 制品的物理机械性能应符合表2。 表2 项目　要求 耐寒试验　应无明显变形及开裂 跌落试验　应不破裂 注：制品进行耐寒试验时，同一制品中包含不同材质配件的，按配件本身材质所应对的试验温度进行试验。 4.7 卫生指标 食品接触用制品应符合GB 4806.7的要求。 5　试验方法 5.1 外观 按QB/T 2357-1998中的4.2进行检测。 5.2 容量 按QB/T 2357-1998中的4.5进行检测。 5.3 高度差 按QB/T 2357-1998中的4.3进行检测。 5.4 密封性能 按QB/T 2357-1998中的4.6.1进行检测。 5.5 耐寒试验 按QB/T 2357-1998中的4.6.4进行检测。 5.6 跌落试验  按QB/T 2357-1998中的4.6.3方法进行检测，跌落高度为1.2m。 5.7 卫生指标 按GB 4806.7的规定进行。迁移量按GB 31604.1的规定进行。 6　检验规则 6.1组批与抽样。 制品以统一投料、同一配方、同一工艺生产包装好的同一规格的制品。每批制品随机抽取6个样品进行检验。 6.2 制品检验分出厂检验和型式检验。 6.3出厂检验 制品需经生产厂质检部门按本标准检验合格，并附合格证方可出厂。出厂检验项目为本标准规定的外观、高度差、密封性能、跌落试验。 6.4 型式检验 型式试验的检验项目为本标准全部项目。 6.5 在以下情况之一时，应进行型式试验： a)　新制品的试制定性鉴定时； b)　工艺、原材料有较大改变，可能影响制品质量时； c)　正常生产每年至少进行两次； d)　长期停产后恢复生产时； e)　国家质量监督机构提出进行型式检验的要求时。 6.6 型式检验样品应在出厂检验合格品种随机抽取。 6.7 判定规则 食品接触用制品若检验结果中出现项目不合格时，则判定该批次制品不合格。 7　标志、使用说明书、包装、运输和储存 7.1 标志 7.1.1 制品标签 制品应有标签标志并标明：制品名称、材质、规格（或货号）、厂名、厂址、执行标准号、生产日期（或批号）等。对于食品用制品其标签符合GB/T 30643规定，并应标注“食品接触用”标识。 7.1.2 外包装储运图示标志  应符合GB/T 191的有关规定。 7.1.3 回收标志 应符合GB/T 16288的有关规定。 7.2 使用说明书 制品使用说明书应符合GB 5296.1的规定。 7.3 包装 制品内包装材料应符合食品包装材料卫生要求。 7.4 运输 运输工具应清洁、卫生、干燥，并具备防晒、防雨设施及机械损伤。运输过程中严禁重压，不得与有毒、有腐蚀性、有异味的物品混运。 7.5 储存 制品应储存于通风、干燥、阴凉的仓库中，防止重压，并远离热源。 7.6 保质期 食品接触用制品的保质期为1年。

Plastic bottles for food packaging

ASTM D3935-21 聚碳酸酯（PC）未填充和增强材料的标准分类系统和规范基础

1.1 This classification system covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions may also find use for compression molding or application from solution. This classification system allows for the use of recycled materials provided that all specification requirements are met. 1.2 The properties in this classification system are those required for identifying the compositions covered. Other requirements necessary for identifying particular characteristics important to specific applications are normally specified by using the suffixes in accordance with Section 5. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field only after consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered in this standard. NOTE 1—This classification system and ISO 21305-1 and ISO 21305-2 address the same subject matter, but differ in technical content. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material

T/SHBX 009-2021 《全生物降解刀叉勺》

本文件规定了全生物降解刀叉勺（以下简称刀叉勺）的术语和定义、分类、技术要求、试验方法、检验规则、包装、包装标志、运输和贮存。

Biodegradable knife,fork and spoon

T/SHPTA 011-2021 全生物降解刀叉勺

本文件规定了全生物降解刀叉勺（以下简称刀叉勺）的术语和定义、分类、技术要求、试验方法、检验规则、包装、包装标志、运输和贮存

Biodegradable knife,fork and spoon

T/WS 0003-2021 家用电器外壳用聚碳酸酯（PC）再生料

标准主要内容包括：本文件规定了家用电器外壳用聚碳酸酯（PC）再生料的术语和定义、命名规则、要求、试验方法、检验规则、标志、包装、运输和贮存等几个方面对标准进行编制。

Polycarbonate (PC) recycled materials for housing of household appliances

T/XTFZZ 003-2021 口罩用全塑型聚乙烯鼻梁条

本标准规定了口罩用全塑型聚乙烯鼻梁条（以下简称鼻梁条）的要求、试验方法、检验规则、标志、包装、运输和贮存等。

All plastic polyethylene nose bridge strip for mask

ISO 6691:2021 滑动轴承用热塑性聚合物.分类和名称

This document specifies a classification and designation system for a selection of the most common unfilled thermoplastic polymers for plain bearings. The unfilled thermoplastic polymers are classified on the basis of appropriate levels of distinctive properties, additives and information about their application for plain bearings. The designation system does not include all properties; thermoplastic polymers having the same designation cannot therefore be interchanged in all cases. It also provides an outline of the properties and applications of the most common unfilled thermoplastic polymers as well as listing some of the fundamental parameters that influence the selection of thermoplastic polymers for use for plain bearings. NOTE In the further course of the work, it is intended to prepare standards on “thermosetting polymers” and “mixed polymers” for plain bearings.

Thermoplastic polymers for plain bearings — Classification and designation

T/GDES 64-2021 原位扩链改性再生塑料颗粒的技术要求

本文件规定了原位扩链改性再生塑料颗粒的总体设计、工艺技术、评价指标、污染控制等内容。 本文件适用于老化后可产生羟基、羧基等基团的废塑料，如含有不饱和双键的聚苯乙烯类废塑料等，这些基团可通过化学反应与扩链剂进行原位扩链化学反应。

Technical requirements for in situ chain extension modified recycled plastic particles

ASTM D6248-21 红外分光光度法测定聚乙烯中乙烯基和反式不饱和度的标准试验方法

1.1 This test method covers most types of polyethylene, those ethylene plastics consisting of ethylene and α-olefin comonomers longer than propylene, and blends of the above in any ratio. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8. NOTE 1—There is no known ISO equivalent for this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry

ASTM F3034-21 通过缠绕熔融挤压应力额定高密度聚乙烯（HDPE）制成的坯料的标准规范

1.1 This specification covers billets made from stress-rated high-density polyethylene (HDPE) materials. 1.2 The billets are manufactured by application of molten extruded material onto a rotating mandrel to form a monolithic mass. Removal of the mandrel provides a billet in the approximate shape of a thick-walled cylindrical shell. Machining prior to dimensioning is acceptable. NOTE 1—Although it is impossible to address all manufacturing details related to the fabrication of billets in this specification, successful heat fusion bonding of HDPE is obtained through controlled application of sufficient heat to cause melting in combination with applied force over a period of time. 1.3 The billets are intended for fabrication into pipe fittings such as flange adapters and reducers. 1.4 Requirements for and use of the fabricated pipe fittings shall be in accordance with an applicable product specification. This specification for billets does not include requirements for items fabricated from the billets. 1.5 This specification includes thermoplastic pipe material designation codes for selection of appropriate stress-rated material, together with performance requirements for billets and test methods for determining conformance with the requirements. 1.6 Minimum quality control measures are prescribed for manufacturers. See Annex A1 for quality control for billets conforming to this specification. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)

ASTM D6878/D6878M-21 热塑性聚烯烃基薄屋面的标准规范

1.1 This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims. 1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended purpose. In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are factors which should be considered but are beyond the scope of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermoplastic Polyolefin-Based Sheet Roofing

DIN 78005-1:2021 塑料 热塑性加工用热塑性硫化橡胶（PP+EPDM） 第1部分：命名系统和规范基础

This document establishes a system of designation for thermoplastic vulcanizates for thermoplastic processing, which may be used as the basis for specifications. The types of thermoplastic vulcanizates for thermoplastic processing are differentiated from each other by a classific

Plastics - Thermoplastic vulcanizates for thermoplastic processing (PP+EPDM) - Part 1: Designation system and basis for specifications

DIN 78005-2:2021 塑料 热塑性加工用热塑性硫化橡胶（PP+EPDM） 第2部分：试样的制备和性能测定

This document specifies the methods for preparation of test specimens and the standard test methods to be used in determining the properties of compounded thermoplastic vulcanizates for thermoplastic processing based on PP/EPDM. This document specifies requirements for handling t

Plastics - Thermoplastic vulcanizates for thermoplastic processing (PP+EPDM) - Part 2: Preparation of test specimens and determination of properties

T/CPCIF 0149-2021 聚丙烯熔喷专用料 二叔丁基过氧化物（DTBP）和2,5-二甲基-2,5-二(叔丁基过氧基)己烷（DBPH）残留量的测定

方法提要 将样品在一定体积的四氢呋喃溶剂中溶解或溶胀，溶剂中含有已知量的正十一烷作为内标物。用微量进样器吸取适量溶液，直接注入气相色谱仪或气质联用仪中，在一定条件下进行气相色谱或气质联用分析，用内标标准曲线法定量。

Polypropylene materials for meltblown—Determination of di-tert-butyl peroxide （DTBP）and 2,5-dimethyl-2,5-di(tert-butylperoxy)hexane（DBPH）

T/CPCIF 0148-2021 塑料 超高流动性聚丙烯材料 熔体体积流动速率（MVR）和熔体质量流动速率（MFR）的测定

在规定的温度和负荷下，由通过规定长度和内孔直径的口模挤出的熔融物质测定熔体体积流动速率（MVR），通过计算转化为熔体质量流动速率（MFR）。 测定MVR，记录活塞在规定时间内的位移或活塞移动规定的距离所需的时间，计算挤出速率，以cm3/10 min表示。 用测量的MVR值乘以材料的熔体密度，计算MFR，以g/10 min表示。

Plastics—Ultrahigh melt fluidity polypropylene materials— Determination of melt volume-flow rate（MVR）and melt mass-flow rate（MFR）

T/CPCIF 0150-2021 塑料 灰分的测定 程控灰化炉法

将装有试样的坩埚置于程控灰化炉中，根据试样材料类型和选择的试样量设置合适的熔化、炭化和灰化三个程控试验阶段的加热温度和加热时间，使试样在程控试验程序控制下自动完成熔化、炭化和高温煅烧灰化过程，直至灰化恒重，根据试验前后试样质量之差计算灰分含量。

Plastics—Determination of ash— Program-controlled ashing furance method

T/CPCIF 0147-2021 口罩用聚丙烯（PP）熔喷专用料

序号　项    目　要    求 　　PPH，Y，1000M　PPH，Y，1200M　PPH，Y，1500M 1.1　颗粒外观　黑粒/（个/kg）　0 1.2　　大粒和小粒/（g/kg）　≤10 2　熔体质量流动速率（MFR）/（g/10 min）　1000±60　1200±70　1500±80 3　灰分（质量分数）/%　≤0.025 4　挥发分（质量分数）/%　≤0.2 5　过氧化物残留总量/（mg/kg）　≤5.0 6　分子量分布　2.0～3.5 7　气味/级　≤4.0

Meltblown polypropylene（PP）materials for mask

ASTM D4477-21 硬质（未增塑）聚氯乙烯（PVC）拱腹标准规范

Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit