83.100 泡沫材料 标准查询与下载

T/LJH 026-2023 绝热用交联聚乙烯泡沫塑料

本标准规定了绝热用交联聚乙烯泡沫塑料的术语和定义、分类和标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Cross-linked polyethylene foam for thermal insulation

ISO 7231:2023 聚合物材料 多孔 柔性 恒定压降下空气流量值的测定

Polymeric materials, cellular, flexible — Determination of air flow value at constant pressure-drop

T/CPF 0056-2023 聚苯乙烯泡沫熔结性试验方法 落锥冲击法

本文件规定了聚苯乙烯泡沫熔结性的试验原理、试验设备、样品、试验步骤、试验数据处理和试验报告。

Test method for fusion of polystyrene foam— Falling cone impact method

23/30456550 DC BS ISO 6916-2 柔性多孔聚合材料 海绵和发泡橡胶制品 规范 第 2 部分：模制品和挤压制品

BS ISO 6916-2. Flexible cellular polymeric materials. Sponge and expanded cellular rubber products. Specification - Part 2. Mouldings and extrusions

ASTM D1621-16(2023) 硬质泡沫塑料压缩性能的标准试验方法

1.1 This test method describes a procedure for determining the compressive properties of rigid cellular materials, particularly expanded plastics. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This test method and ISO 844 are technically equivalent. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Compressive Properties of Rigid Cellular Plastics

ASTM D1623-17(2023) 硬质泡沫塑料的拉伸和拉伸粘合性能的标准试验方法

1.1 This test method covers the determination of the tensile and tensile adhesion properties of rigid cellular materials in the form of test specimens of standard shape under defined conditions of temperature, humidity, and testing machine speed. 1.2 Tensile properties shall be measured using any of three types of specimens: 1.2.1 Type A shall be the preferred specimen in those cases where enough sample material exists to form the necessary specimen. 1.2.2 Type B shall be the preferred specimen when only smaller specimens are available, as in sandwich panels, etc. 1.2.3 Type C shall be the preferred specimen for the determination of tensile adhesive properties of a cellular plastic to a substrate as in a sandwich panel (top and bottom substrate) or the bonding strength of a cellular plastic to a single substrate. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. NOTE 1—There is no known ISO equivalent to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

T/CASME 330-2023 家居用高回弹软质聚氨酯泡沫塑料

本文件规定了家居用高回弹软质聚氨酯泡沫塑料的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

High resilience flexible polyurethane foam for household use

ASTM C950/C950M-08(2023) 室外服务容器上硬质泡沫聚氨酯绝缘系统修理的标准实施规程

1.1 This practice covers the repair of spray-applied polyurethane insulation on vessels normally operating at temperatures between −30 and +107°C [−22 and +225°F]. 1.2 Warning—At temperatures below 0°C [32°F] the application of a spray “foam” directly onto the cold substrate may not be possible. The term “foam” applies to spray-applied polyurethane or polyisocyanurate (PUR or PIR) rigid cellular plastic only, and not to any other plastic insulation. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement see 1.2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Repair of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels

ASTM C945-05(2023) 室外服务容器上硬质泡沫聚氨酯绝缘系统的设计考虑和喷涂应用的标准实施规程

1.1 This practice concerns itself with the substrate preparation and priming, the selection of the rigid cellular polyurethane system, and the protective insulation coatings for outdoor service equipment. NOTE 1—For the purpose of this practice, polyurethane is defined to mean either polyurethane or polyisocyanurate and is hereafter referred to as “PUR/PIR.” 1.2 The values given in inch-pound are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Design Considerations and Spray Application of a Rigid Cellular Polyurethane Insulation System on Outdoor Service Vessels

ASTM C1594-23 聚酰亚胺硬质蜂窝绝热材料标准规范

1.1 This specification covers the composition and physical properties of polyimide foam insulation with nominal densities from 1.0 lb/ft3 to 8.0 lb/ft3 (16 kg ⁄m3 to 128 kg/m3 ) and intended for use as thermal and sound-isolating insulation for temperatures from −423°F to +600°F (−253°C to +316°C) in commercial and industrial environments. 1.1.1 The annex shall apply to this specification for marine applications. 1.1.2 This standard is designed as a material specification and not a design document. 1.1.3 The values stated in Table 1 and Table 2 are not to be used as design values. It is the buyer’s responsibility to specify design requirements and obtain supporting documentation from the material supplier. NOTE 1—The subject matter of this material specification is not covered by any other ASTM specification. There is no known ISO standard covering the subject of this standard. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyimide Rigid Cellular Thermal Insulation

ASTM D6694/D6694M-15(2023) 喷涂聚氨酯泡沫屋顶系统用液体涂敷硅涂层的标准规范

1.1 This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone. 1.2 This specification does not provide guidance for application. 1.3 The following precautionary caveat pertains only to the test method portions, Sections 5 and 6. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems

ASTM C534/C534M-23 薄板和管状预制柔性弹性泡沫绝热材料标准规范

1.1 This specification covers preformed flexible elastomeric cellular-thermal insulation in sheet and tubular form. Grade 1 covers materials to be used on commercial or industrial systems with operating temperatures from –183 to 104°C [–297 to 220°F], Grade 2 covers material used on industrial systems with operating temperatures from –183 to 150°C [–297 to 300°F], and Grade 3 covers material used on industrial systems with operating temperatures from –183 to 120°C [–297 to 250°F] where halogens are not permitted. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form

T/CNLIC 0068-2022 绿色设计产品评价技术规范 发泡海绵枕垫

本文件规定了发泡海绵枕垫绿色设计产品的评价要求，描述了产品生命周期评价方法及评价报告编制方法和评价方法。

Technical specification for green-design product assessment— Foam pillow pad and mattress

KS M ISO 2440-2022 柔性和刚性多孔聚合物材料.加速老化试验

Flexible and rigid cellular polymeric materials — Accelerated ageing tests

KS M ISO 1856-2022 柔性泡沫聚合材料压缩永久变形的测定

Flexible cellular polymeric materials Determination of compression set

ASTM C591-22 未经加工的预制刚性多孔聚异氰尿酸盐隔热材料标准规范

1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocyanurate plastic material intended for use as thermal insulation on surfaces from –297°F (–183°C) to 300°F (149°C). For specific applications, the actual temperature limits shall be agreed upon by the manufacturer and purchaser. 1.2 This specification only covers “polyurethane modified polyisocyanurate” thermal insulation which is commonly referred to as “polyisocyanurate” thermal insulation. This standard does not encompass all polyurethane modified materials. Polyurethane modified polyisocyanurate and other polyurethane materials are similar, but the materials will perform differently under some service conditions. 1.3 This standard is designed as a material specification, not a design document. Physical property requirements vary by application and temperature. At temperatures below –70°F (–51°C) the physical properties of the polyisocyanurate insulation at the service temperature are of particular importance. Below –70°F (–51°C) the manufacturer and the purchaser must agree on what additional cold temperature performance properties are required to determine if the material can function adequately for the particular application. 1.4 This standard addresses requirements of unfaced preformed rigid cellular polyisocyanurate thermal insulation manufactured using blowing agents with an ozone depletion potential of 0 (ODP 0). 1.5 Except 6.2 and 8.2 – 8.4, which are related to the size and shape of fabricated parts, and 16.1, which is related to the storage of fabricated parts, the requirements in this standard specification apply to the polyisocyanurate insulation in the form of buns supplied by the insulation manufacturer. 1.6 When adopted by an authority having jurisdiction, codes that address fire properties in many applications regulate the use of the thermal insulation materials covered by this specification. Fire properties are controlled by job, project, or other specifications where codes or government regulations do not apply. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

T/CASME 91-2022 汽车用膨胀胶微孔材料

本文件规定了汽车用膨胀胶微孔材料的要求、试验方法、检验规则、标志、包装、运输和贮存。

Expanded sealing microporous material for automotive

T/CASME 67-2022 汽车引擎舱隔音隔热聚氨酯板材

本文件规定了汽车引擎舱隔音隔热聚氨酯板材的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。

Polyurethane sheet for sound insulation and heat insulation of automobile engine compartment

ASTM D7605-11(2022) 用无转子剪切流变仪测量聚合物熔体流变特性和凝固动态特性的热塑性弹性体的标准试验方法

1.1 This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of polymer melts and their respective congealed dynamic properties for thermoplastic elastomers (TPE) which includes thermoplastic vulcanizates (TPV). These flow properties and congealed dynamic properties are related to factory processing and product performance. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermoplastic Elastomers—Measurement of Polymer Melt Rheological Properties and Congealed Dynamic Properties Using Rotorless Shear Rheometers

22/30435835 DC BS ISO 1663 硬质泡沫塑料 水蒸气透过性能的测定

BS ISO 1663. Rigid cellular plastics. Determination of water vapour transmission properties