83.140.01 橡胶和塑料制品综合 标准查询与下载

DB22/T 2106-2018 聚乳酸制品通用技术要求

General technical requirements for polylactic acid products

T/ZZB 0377-2018 高生物碳塑料购物袋

本标准规定了高生物碳塑料购物袋（以下简称购物袋）的术语与定义、基本要求、技术要求、试验方法、检验规则、包装、包装标识、运输和贮存、质量保证与服务。 本标准适用于生物聚乙烯树脂为主要原料生产的薄膜、经热合或粘合等制袋工艺加工制得的购物袋。

High biobased carbon content plastic shopping bags

ASTM D6108-18 塑料木材和型材压缩性能的标准试验方法

1.1 This test method covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading. Test specimens in the “as-manufactured” form are employed. As such, this is a test method for evaluating the properties of plastic lumber or shapes as a product and not a material property test method. 1.2 Plastic lumber and plastic shapes are currently made predominantly with recycled plastics. However, this test method would also be applicable to similar manufactured plastic products made from virgin resins, or where the product is non-homogenous in the cross-section. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this test method. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Compressive Properties of Plastic Lumber and Shapes

ASTM D6117-18 塑料木材和型材机械紧固件的标准试验方法

1.1 These test methods cover the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures. 1.2 The test methods appear in the following order: Sections Test Method A—Nail, Staple, or Screw Withdrawal Test 4 to 13 Test Method B—Lateral Nail, Staple, or Screw Resistance Test 14 to 22 1.3 Plastic lumber and plastic shapes are currently made predominately from recycled plastics. However, these test methods would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogeneous in the cross-section. 1.4 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes

ASTM D6112-18 塑料木材和型材的压缩和弯曲蠕变和蠕变破裂的标准测试方法

1.1 These test methods cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed. As such, these are test methods for evaluating the properties of plastic lumber or shapes as a product and not material property test methods. 1.2 Plastic lumber and plastic shapes are currently made predominantly with recycled plastics. However, this test method would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogenous in the cross-section. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes

ASTM D6111-18 用位移法测定塑料木材和形状的堆积密度和比重的标准试验方法

1.1 This test method covers the determination of the bulk density and specific gravity of plastic lumber and shapes in their “as manufactured” form. As such, this is a test method for evaluating the properties of plastic lumber or shapes as a product and not a material property test method. 1.2 This test method is suitable for determining the bulk specific gravity or bulk density by immersion of the entire item or a representative cross section in water. This test method involves the weighing of a one piece specimen in water, using a sinker with plastics that are lighter than water. This test method is suitable for products that are wet by, but otherwise not affected by water for the duration of the test. 1.3 Plastic lumber and plastic shapes are currently made predominately from recycled plastics. However, this test method would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogeneous in the cross-section. 1.4 The values stated in SI units are to be regarded as standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this test method. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement

T/CSIQ 76002-2018 塑料及塑料复合材料的包装件和包装容器 水蒸气透过性试验方法 电解传感器法

本标准规定了在稳态条件下采用电解传感器法对塑料及塑料复合材料的包装件和包装容器水蒸气透过性进行测试的试验方法，包括术语和定义、原理、试样、样品状态调节和试验环境、试验仪器及辅助材料、试验条件、试验步骤、结果计算呵试验报告等。

Plastic and plastic composite packages and packaging containers－Test method for water vapor transmission rate－Electrolytic detection sensor method

ASTM D6110-18 测定塑料缺口试样夏氏冲击强度的标准试验方法

1.1 This test method is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized (see Note 1) pendulumtype hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing. This test method requires specimens to be made with a milled notch (see Note 2). The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. The results of this test method are reported in terms of energy absorbed per unit of specimen width (see Note 3). NOTE 1—The machines with pendulum-type hammers have been standardized in that they must comply with certain requirements including a fixed height of hammer fall, which results in a substantially fixed velocity of the hammer at the moment of impact. Hammers of different initial energies (produced by varying their effective weights), however, are recommended for use with specimens of different impact resistance. Moreover, manufacturers of the equipment are permitted to use different lengths and constructions of pendulums with possible differences in pendulum rigidities resulting (see Section 5). Be aware that other differences in machine design do exist. NOTE 2—The specimens are standardized in that they have a fixed length and fixed depth, however, the width of the specimens is permitted to vary between limits. One design of milled notch is allowed. The notch in the specimen serves to concentrate the stress, minimize plastic deformation, and direct the fracture to the part of the specimen behind the notch. Scatter in energy-to-break is thus reduced. Because of differences in the elastic and viscoelastic properties of plastics, however, response to a given notch varies among materials. NOTE 3—Caution must be exercised in interpreting the results of this test method. The following testing parameters have been shown to affect test results significantly: method of specimen fabrication, including but not limited to processing technology, molding conditions, mold design, and thermal treatment; method of notching; speed of notching tool; design of notching apparatus; quality of the notch; time between notching and test; test specimen thickness; test specimen width under notch; and environmental conditioning. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 4—This standard resembles ISO 179 in title only. The content is significantly different. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics

ASTM D4803-10(2018)e1 预测聚氯乙烯建筑产品中热积累的标准试验方法

1.1 This test method covers prediction of the heat buildup in rigid and flexible PVC building products above ambient air temperature, relative to black, which occurs due to absorption of the sun’s energy. NOTE 1—This test method is expected to be applicable to all types of colored plastics. The responsible subcommittee intends to broaden the scope beyond PVC when data on other materials is submitted for review. NOTE 2—There are no ISO standards covering the primary subject matter of this test method. 1.2 Rigid PVC exterior profile extrusions for assembled windows and doors are covered in Specification D4726. 1.3 Rigid PVC exterior profiles for fencing are covered in Specification F964. 1.4 Rigid PVC siding profiles are covered in Specification D3679. 1.5 Rigid PVC soffit profiles are covered in Specification D4477. 1.6 Rigid PVC and Rigid CPVC plastic building products compounds are covered in Specification D4216. 1.7 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method. 1.8 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety hazard statements are given in Section 7. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Predicting Heat Buildup in PVC Building Products

T/SPEA 0001-2017 氧化生物双降解快递包装袋

本标准规定了包装用氧化生物双降解快递袋及其制品的定义、技术要求、试验方法、检验规则及标志、包装、运输、贮存。

Oxidative biodegradable express packaging bag

KS M ISO 20299-1-2017 橡胶包装胶带 - 第1部分:丁二烯橡胶（br）和苯乙烯 - 丁二烯橡胶（sbr）

Film for wrapping rubber bales — Part 1: Butadiene rubber(BR) and styrene-butadiene rubber(SBR)

KS M ISO 20299-1:2017 橡胶面纱包装用胶片 第1部分：丁二烯橡胶（BR）和苯乙烯 丁二烯橡胶（SBR）

Film for wrapping rubber bales — Part 1: Butadiene rubber(BR) and styrene-butadiene rubber(SBR)

KS M ISO 20299-1-2017(2022) 橡胶包包装膜.第1部分:丁二烯橡胶（BR）和丁苯橡胶（SBR）

Film for wrapping rubber bales — Part 1: Butadiene rubber(BR) and styrene-butadiene rubber(SBR)

ASTM D6110-17 测定塑料缺口试样夏氏冲击强度的标准试验方法

Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics

KS G 5603-2017 微波炉用塑料食品容器

Plastics food receptacles for microwave oven use

KS G 5603-2017(2022) 微波炉用塑料食品容器

Plastics food receptacles for microwave oven use

T/YKSL 001-2017 双向拉伸聚丙烯（BOPP）食品包装袋

原材料要求、尺寸偏差、印刷质量、外观质量、物理机械性能、卫生性能

Biaxially oriented polypropylene (BOPP) food packaging bags

SN/T 4842-2017 塑料及橡胶材料中偶氮二甲酰胺的测定 高效液相色谱法

Determination of azodicarbonamide in plastic and rubber materials by high performance liquid chromatography

SN/T 4843-2017 橡胶制品中铬、钴、砷、溴、钼、镉、锡和铅的测定 电感耦合等离子体质谱法

Determination of chromium, cobalt, arsenic, bromine, molybdenum, cadmium, tin and lead in rubber products by inductively coupled plasma mass spectrometry

T/DLQG 1002-2017 罐头物流塑料箱

项目特点 ：本标准产品特点：增进商品销售美观感；降低物流成本，节约资源；贮运保管快捷方便、安全卫生等。因此，农牧渔各产业罐装食品的生产、包装、仓储等物流环节广泛采用塑料箱。  项目先进性 ：本标准技术水平为国内先进水平。因此，该标准项目对指导和规范生产企业有序竞争、科学发展，维护消费者的合法权益，更好地为贸易服务，保持包装产业经济的良性循环可持续健康发展，具有重要意义。 项目创新性：国内无罐头物流塑料箱产品的国家标准和行业标准。本标准在技术方面对产品的外观、原材料选用、机械性能规定了详尽的指标；为符合

Canned logistics plastic box