83.140.01 橡胶和塑料制品综合 标准查询与下载

GOST 30973-2002 门窗的聚氯乙烯型材.耐气候性的测定方法和使用寿命评估

Polyvinylchloride profiles for windows and doors. Method of determination of resistance to climatic effects and estimation of life circle

UL 746C-2001 电气设备评定用聚合材料

Polymeric materials - Use in electrical equipment evaluations

ISO 3302-1:1996/Amd 1:2001 橡胶 产品公差 第1部分:尺寸公差 修改1

This is Amendment 1 to ISO 3302-1-1996 (Rubber — Tolerances for products — Parti: Dimensional tolerances AMENDMENT 1: Classification system for flash )

Rubber - Tolerances for products - Part 1: Dimensional tolerances; Amendment 1: Classification system for flash

CNS 10774-2001 自来水管件用橡胶制品

本标准适用于自来水用管接头及管阀所用保持水密性用之橡胶制品 (以下称橡胶品) ，但不适用于给水器具及供热水流通用橡胶品之浸出性。注：本标准中 { } 之单位为公制，数值系近似值。

Rubber goods for water works

ANSI/ICPA SS-1-2001 固体表面材料的性能标准

Establishes minimum performance requirements for solid surface materials including workmanship, structural integrity and physical characteristics such as stain resistance, cleanability, impact and water resistance and ability for the surface to be seamlessly fabricated and renewed.

Performance Standard for Solid Surface Materials

GOST 19111-2001 内部装饰用聚氯乙烯异型装饰线制品.技术条件

Polyvinylchloride shaped linear articles for interior finish. Specifications

ANSI/ASTM D1972:2001 塑料90-03第55项通用标记惯例

This practice covers a system for uniform marking of products that have been fabricated from polymeric materials. Provision for the process or processes to be used for marking is outside the scope of this practice. Note 1 -Precise details of the marking, for example, the minimum size of the item to be marked, the size of the lettering, and the appropriate location of the marking, may be subject to agreement between the manufacturer and the user. The abbreviated terms used are to provide generic identification of the polymer(s). This practice is especially pertinent for use with durable plastic components of products. This practice is not intended to supplant, replace, or in any way interfere with the requirements found in legislation for marking or labeling of packaging. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2 -In many respects, this practice is similar to ISO 11469.

Practice for Generic Making of Plastics 90-03 Item 55 (08.01)

ANSI/ASTM D5418:2001 用双悬臂束测试塑料动态机械特性的方法

This test method outlines the use of dynamic mechanical instrumentation for determining and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular bars molded directly or cut from sheets, plates, or molded shapes. The elastic modulus data generated may be used to identify the thermomechanical properties of a plastics material or composition. This test method is intended to provide a means for determining the viscoelastic properties of a wide variety of plastics using nonresonant, forced-vibration techniques as outlined in Practice D 4065. In particular, this method identifies the procedures used to measure properties using what is known as a dual-cantilever beam flexure arrangement. Plots of the elastic (storage) modulus, loss (viscous) modulus, and complex modulus, and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of the polymeric material systems. This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz. Apparent discrepancies may arise in results obtained under differing experimental conditions. These apparent differences from results observed in another study can usually be reconciled, without changing the observed data, by reporting in full (as described in this test method) the conditions under which the data were obtained. Test data obtained by this test method are relevant and appropriate for use in engineering design. The values stated in SI units are to be regarded as standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There is no known ISO equivalent to this standard.

Test Method for Measuring the Dynamic Mechanical Properties of Plastics Using a Dual Cantilever Beam (08.03)

UL 746C BULLETINS-2001

1.1 These requirements cover parts made of polymeric materials that are used in electrical equipment and describe the various test procedures and their use in the testing of such parts and equipment. 1.2 These requirements do not cover the specific insulating systems that are covered by the requirements contained in the Standard for Systems of Insulating Materials, General, UL 1446. 1.3 Test procedures are provided herein for the evaluation of polymeric materials in specific applications. These test procedures include references to data obtained from small-scale property tests conducted under standard conditions as well as other practical means of evaluation. This new edition also includes revisions for the Clarification of End-Product Flammability Tests and some other general editorial revisions as proposed in the August 8, 2003 bulletin.

6/13/2001 (20p), 6/6/2001 (18p), 4/3/2001 (10p), 3/20/2001 (6p)

ANSI/ASTM D6662:2001 聚烯烃基塑料废物盖板规范

This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards. Plastic lumber products are currently made predominantly with recycled polyolefin plastics (in particular high-density polyethylene) where the products are more or less non-homogenous in the cross-section. However, this specification is also potentially applicable to similar manufactured plastic products made from other plastic and plastic composite materials that have non-homogenous cross-sections. This specification details a procedure to calculate recommended span lengths for spacing of support joists. This procedure was developed using experimental data from a typical unreinforced plastic lumber made predominantly from recycled high-density polyethylene. The methodology to develop span lengths for other types and compositions of plastic lumber is detailed in Appendix X1 of this standard. The values are stated in inch-pound units, as these are currently the most common units used by the construction industry. Equivalent SI units are indicated in parentheses. However, the units stated for irradiance exposure in the weatherability section (6.3) are in SI units as these are the units commonly used for testing of this type. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There is no similar or equivalent ISO Standard.

Specification for Polyolefin-Based Plastic Lumber Decking Boards

DIN EN ISO 11469:2000 塑料.塑料产品通用标识和标记

Plastics - Generic identification and marking of plastics products (ISO 11469:2000); German version EN ISO 11469:2000

BS EN ISO 11469:2000 塑料.塑料产品的通用识别方法和标记

1 This International Standard specifies a system of uniform marking of products that have been fabricated from plastics materials. Provision for the process or processes to be used for marking is outside the scope of this standard. NOTE Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate location of the marking, are subject to agreement between the manufacturer and the user. 2 The marking system is intended to help identify plastics products for subsequent decisions concerning handling, waste recovery or disposal. 3 Generic identification of the plastics is provided by the symbols and abbreviated terms given in ISO 1043, parts 1 to 4. NOTE If more detailed information for material identification is needed, additional marking of plastics products can be applied as defined in the appropriate product standard. 4 This International Standard is not intended to supplant, replace or in any way interfere with requirements for labelling found in legislation.

Plastics - Generic identification and marking of plastics products

NF T50-060:2000 塑料制品.塑料产品一般识别和标记

Plastics - Generic identification and marking of plastics products.

EN ISO 11469:2000 塑料.塑料产品的一般鉴定和标志 ISO 11469-2000

Plastics - Generic Identification and Marking of Plastics Products ISO 11469:2000

ISO 11469:2000 塑料 塑料产品的一般鉴定和标志

1 This International Standard specifies a system of uniform marking of products that have been fabricated from plastics materials. Provision for the process or processes to be used for marking is outside the scope of this standard. NOTE Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate location of the marking, are subject to agreement between the manufacturer and the user. 2 The marking system is intended to help identify plastics products for subsequent decisions concerning handling, waste recovery or disposal. 3 Generic identification of the plastics is provided by the symbols and abbreviated terms given in ISO 1043, parts 1 to 4. NOTE If more detailed information for material identification is needed, additional marking of plastics products can be applied as defined in the appropriate product standard. 4 This International Standard is not intended to supplant, replace or in any way interfere with requirements for labelling found in legislation.

Plastics - Generic identification and marking of plastics products

ASTM D5033-00 有关再循环和再循环塑料使用的ASTM标准的制定标准指南

1.1 This guide provides information for the development of ASTM standards (guides, practices, terminology, test methods, and specifications) relating to recycling and the use of recycled plastics.1.2 This guide is directed to consumer, commercial, and industrial products made in whole or in part with recycled plastics or recovered plastic products.1.3 This guide addresses terminology, performance standards, specifications and their revisions, quality assurance, separation or segregation of products by classes, identification and labeling of generic classes of polymers, contaminants, fillers, designing for recycling, degradable plastics, and certification and percentages of recycled plastics.1.4 This guide does not address general parameters or factors involving the original manufacture of virgin polymers or the fabrication of consumer products from these virgin polymers.1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1--There is no equivalent ISO standard.

Standard Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics

ANSI/ASTM D5033:2000 再生塑料正确使用标准编制指南 (08.03)

This guide provides information for the development of ASTM standards (guides, practices, terminology, test methods, and specifications) relating to recycling and the use of recycled plastics. This guide is directed to consumer, commercial, and industrial products made in whole or in part with recycled plastics or recovered plastic products. This guide addresses terminology, performance standards, specifications and their revisions, quality assurance, separation or segregation of products by classes, identification and labeling of generic classes of polymers, contaminants, fillers, designing for recycling, degradable plastics, and certification and percentages of recycled plastics. This guide does not address general parameters or factors involving the original manufacture of virgin polymers or the fabrication of consumer products from these virgin polymers. This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1--There is no equivalent ISO standard.

Guide for the Development of Standards Relating to the Proper Use of Recycled Plastics (08.03)

CNS 14384-3-1999 化学药品及微生物防护手套－抗化学药品渗透性之测定

本标准规定防护手套材料与非气态而具潜在危险之化学药品在继续接触之情况下测定其抗透性。惟须强调的是此项试验不能代表如在使用中所见者，并且试验数据之使用应仅限于主要在广大范畴之贯流时间之相关基础下作材枓之比较。

Protective gloces against chemicals and micro-organisms - Part 3:Determination of resistance to permeation by chemicals

CNS 14384-1-1999 化学药品及微生物防护手套－用语及性能要求

本标准适用于化学药品及微生物用防护手套之性能要求及用语释义。本标准将与 CNS 14382〔防护手套一般要求〕同时使用。

Protective gloves against chemicals and micro-organisms - Part 1:Terminology and performance requirements

CNS 14384.1-1999 化学药品及微生物防护手套－用语及性能要求

Protective gloves against chemicals and micro-organisms - Part 1:Terminology and performance requirements