83.140.10 薄膜和薄板 标准查询与下载

T/SHBX 012-2021 抗菌塑料(复合)软包装

本文件给出了抗菌塑料（复合）软包装的术语和定义、分类和结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Antibacterial plastic(compound) flexible package

T/SDPTA 001-2021 低熔点相容直投包装

本文件规定了低熔点相容直投包装的要求、试验方法、检验规则和标志、包装、运输、贮存。 本文件适用于低熔点相容直投包装产品的生产、检验和销售。

Low melting point compatible drop-in packaging

T/SHPTA 018-2021 抗菌塑料（复合）软包装

本文件给出了抗菌塑料（复合）软包装的术语和定义、分类和结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Antibacterial plastic(compound) flexible package

T/SHBX 011-2021 生物工艺用高阻隔耐穿刺塑料多层膜

本文件给出了生物工艺中一次性使用系统（包括一次性储存系统、一次性配液系统、一次性无菌取样系统及一次性制剂灌装系统等）所使用的膜材的生产及技术要求。

High barrier multi-layer plastic film with puncture resistant for bioprocess

T/SHPTA 017-2021 生物工艺用高阻隔耐穿刺塑料多层膜

本文件给出了生物工艺中一次性使用系统（包括一次性储存系统、一次性配液系统、一次性无菌取样系统及一次性制剂灌装系统等）所使用的膜材的生产及技术要求

High barrier multi-layer plastic film with puncture resistant for bioprocess

T/GDC 133-2021 高强复合格栅

尺寸偏差、颜色及外观、力学性能、耐磨性、耐落锤冲击、耐高温性能、耐低温性能、耐酸性能、耐碱性能、耐紫外老化性能、原材料

High Strength Composite Grid

T/SHMHZQ 098-2021 POF 收缩膜技术规范

4 技术要求  4.1 规格尺寸  4.2 外观质量  4.3 物理机械性能  4.4 卫生性能  5 试验方法  5.1 取样方法  5.2 试样状态调节和试验的标准环境  5.3 规格尺寸  5.4 外观质量  5.5 物理机械性能  5.6 卫生性能  6 检验规则  6.1 组批  6.2 检验分类  6.3 抽样方案  6.4 判定规则  7 标志、包装、运输及贮存

POF shrink film technical specification

T/GDBZ 011-2021 单一材质包装——日化包装用聚乙烯复合膜、袋

本标准规定了日化包装用单一材质聚乙烯复合膜、袋（以下简称复合膜、袋）的分类、要求、试验方法、检验规则和标志、包装、运输和贮存。 本标准适用于以聚乙烯膜材质为原材料，经印刷、复合或涂布、制袋等工艺进行生产的多层日化包装用复合膜、袋。其中印刷、非PE涂层材料使用量不大于5%，且不含PA，PVDC等不利于回收的材料。

Single material packaging - polyethylene composite film and bag for daily chemical packaging

T/CPPIA 12-2021 农用棚膜接触含硫、氯农药影响耐候性的判定

4　判定指标 4.1　力学性能保留率 力学性能保留率应符合表1规定。 表1　力学性能保留率 项目　要求 拉伸强度保留率（纵、横向）/%　≥60 断裂标称应变保留率（纵、横向）/%　≥60 4.2　农药硫、氯残留量 农药硫、氯残留量应符合表2规定。   表2　农药硫、氯残留量 使用期限/年（a）　残留量/(mg/kg) 　硫（S）　氯（CL） a≤1　≤500　≤100 1＜a≤2　≤1000　≤150 a＞2　≤2000　≤180

Determination of the influence of agricultural greenhouse film on weather resistance after exposure to pesticides containing sulfur、chlorine

ASTM D3354-21 用平行板法测定塑料薄膜阻塞负荷的标准试验方法

1.1 This test method yields quantitative information regarding the degree of blocking (unwanted adhesion) existing between layers of plastic film. It is not intended to measure susceptibility to blocking. 1.2 By this procedure, the film-to-film adhesion, expressed as a blocking load in grams, will cause two layers of film with an area of contact of 100 cm2 to separate. The test method is limited to a maximum load of 200 g. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This test method is similar to ISO 11502 Method B, but is not technically equivalent. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method

ASTM G29-21 测定聚合物薄膜耐蓝藻性的标准实施规程

1.1 This practice covers the determination of the susceptibility of polymeric films to the attachment and proliferation of surface-growing cyanobacteria. 1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining Cyanobacterial Resistance of Polymeric Films

T/WS 0004-2021 锂电池用聚丙烯阻燃麦拉膜

标准主要内容包括：本标准规定了锂电池用聚丙烯阻燃麦拉膜的产品分类、要求、试验方法、检验规则、包装、标志、运输及贮存等；技术要求包括外观、尺寸、弯曲度、物理性能、阻燃性能、电性能、表面电阻率、粗糙度、有害物质限量要求。

Polypropylene flame retardant Mylar film for lithium battery

T/TPCX 003-2021 葡萄酒瓶口外包装胶帽

3　产品分类 3.1　按加工方式分为:机卷帽和手工帽。 3.2　按材料分为:铝塑帽、PVC热缩帽、锡帽。 4　技术要求 4.1　规格尺寸 规格尺寸须符合按照BB/T 0018生产的葡萄酒瓶瓶口的规格，可参照图 1 的规定，特殊规格的胶帽可按客户要求或合同规定执行。 4.2　外观质量 4.2.1　外包装胶帽表面应平整、无毛刺。 4.2.2　印刷色调分明、清晰，颜色基本一致，印刷图案和文字完整、无明显漏底、划伤，顶部印刷图案不同心偏差为±0.5 mm。 4.2.3　接口处应粘结牢固、无开裂现象，接口错位为 ±0.5 mm。 4.3　物理性能 外包装胶帽经收缩实验试验后应粘结牢固、收缩均匀、不开缝、不变色。 5　试验方法 5.1　规格尺寸 用精度为 0.02 mm 的游标卡尺检验。 5.2　外观质量 5.2.1　外观用目测检验 整体完整无破损，图案字符印刷清晰、表面无污物、油墨喷印无脱落。 5.2.2　顶部印刷图案不同心偏差:测量试样上、下、左、右对称部位的空白宽度（精确到0.02mm）A1、A2，见图2和公式(1)。 图案中心偏差值a=(A1一A2)/2........（1） 5.2.3　接口错位用游标卡尺测量。 5.3　物理性能检测 5.3.1　收缩性能 5.3.1.1　试验设备 根据用户生产线上使用的收缩设备来确定。 5.3.1.2　试验方法 外包装胶帽生产出来24 h后，套在瓶子上，在试验设备上进行收缩或碾压试验，温度和时间的控制因材料和设备而异，热缩后须胶帽保证完整、无皱褶、无瑕疵，紧密，无脱落，满足葡萄酒包装的要求。

Wine bottle outer packaging rubber cap

DIN 53377:2021 塑料薄膜的测试 尺寸稳定性的测定

This document specifies a procedure for determining the dimensional changes of plastic films which may have been caused by various treatments, such as the application of heat.

Testing of plastic films - Determination of dimensional stability

T/CPCIF 0141-2021 浇铸型聚甲基丙烯酸甲酯板材生产安全技术规范

4　通用安全要求 4.1  操作岗位应杜绝跑、冒、滴、漏，保持良好的通风环境，人员应做好管道设备巡查。发生火灾，应立即停车，并立即切断可燃物来源，组织抢救，并应立即报警。 4.2  吊装作业时，严禁人员在吊装路线下方走动、作业。 4.3  人员进行作业前，应做好设备设施检查，确保真空吸盘无裂纹、破损，真空压力满足作业需求。 4.4  厂房建筑应符合GB 50016，甲类火灾危险性范围，应使用防爆电器、工具，电器设备的防爆型式和措施应符合GB 50058防爆要求。甲类区域入口处应设置人体静电释放器。机动车辆进入生产区域速度应小于等于5 km/h。

Technical specification for safety production of polymethyl methacrylate cast sheets

UNI EN ISO 12017:2021 塑料 聚（甲基丙烯酸甲酯）双层和三层板材 试验方法

Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods

OENORM EN ISO 12017:2021 塑料 聚（甲基丙烯酸甲酯）双层和三层板材 测试方法（ISO 12017:2021）

Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods (ISO 12017:2021)

ASTM D6988-21 塑料薄膜试样厚度测定的标准指南

1.1 This guide covers the determination of the thickness of plastic films where the thickness is used directly in determining the results of tests for various properties. Use this practice except as otherwise required in material specifications or in applicable test standards. NOTE 1—Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm (0.010 in.). NOTE 2—Alternative methods are acceptable if they meet the requirements of measurement precision as noted in this guide. NOTE 3—This guide is not intended to address the sampling techniques or the measurement of film thickness for the commercial classification of commercial products or for quality control purposes. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 4—This standard and ISO 4593 address the same subject matter but differ in technical content. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Determination of Thickness of Plastic Film Test Specimens

FprEN ISO 15013:2021 塑料 聚丙烯（PP）挤出板 要求和测试方法（ISO/FDIS 15013:2021）

Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO/FDIS 15013:2021)

DIN EN ISO 12017:2021 塑料 聚（甲基丙烯酸甲酯）双层和三层板材 测试方法（ISO 12017:2021）；德文版 EN ISO 12017:2021

This document specifies the test methods for quality control of poly(methyl methacrylate) (PMMA) extruded double- and triple-skin flat sheets, obtained from colourless and coloured transparent, translucent and opaque grades of materials. The minimum sheet width is 600 mm. The mai

Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods (ISO 12017:2021); German version EN ISO 12017:2021