83.140.10 薄膜和薄板 标准查询与下载

DS/EN 17104:2021 建筑物内部用热塑性塑料硬质防护墙布板材性能特点

Thermoplastics rigid protective wallcovering panels for internal use in buildings – Performance characteristics

T/WS 0001-2021 亚光双向拉伸聚酯（PET)薄膜

主要技术内容： 物理机械性能 项目　                                      要求 　                             公称厚度/μm 　                         50　75　100 拉伸强度/MPa　         纵向　≥180　≥170　≥165 　                         横向　≥190　≥180　≥175 断裂伸长率/% 纵向、横向    100～200　 热收缩率/%              纵向　≤1.2　≤1.0　≤1.0 （150℃/30min）　横向　≤0.3　≤0.3　≤0.3 雾度/%　90～100 透光率/%　42～60 光泽度（45°）/%　≤22 摩擦系数　静　≤0.65 　        动　≤0.55 润湿张力/(mN/m)　电晕处理≥50 　                        非电晕处理≤44

Matt biasially oriented polyester film

T/WS 0002-2021 双向拉伸聚丙烯纸巾包装膜

物理机械性能：                     项目　要求   拉伸强度/MPa　纵向　≥130  横向　≥230   断裂标称应变/%　纵向　≤180  横向　≤70   热收缩率/%　纵向　≤4.5  横向　≤3.5   雾度/%　厚度≤30μm　≤2.0   动摩擦系数　处理面　≤0.25  非处理面　≤0.25   润湿张力/mN/m　处理面　≥38  非处理面　≤32   热封强度/N/15mm　处理面　≥2.0  非处理面　≥2.2   光泽度/%　≥80   透湿量/[g/(㎡·24h·0.1mm)]　≤2.0 注：　非处理面指未经过电晕、火焰或等离子体处理的表面；处理面指经过电晕、火焰或等离子体处理的表面。

Biaxially oriented polypropylene(BOPP) film for napkin packaging

ASTM D1004-21 塑料薄膜和片材的抗撕裂性能（Graves Tear）的标准测试方法

1.1?This test method2 covers the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm (2 in.)/min. and is designed to measure the force to initiate tearing. The specimen geometry of this test method produces a stress conc

Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting

ASTM D1790-21 冲击塑料薄片脆性温度的标准测试方法

1.1?This test method covers the determination of that temperature at which plastic sheeting 1.00 mm (0.040 in.) or less in thickness exhibits a brittle failure under specified impact conditions. 1.2?The values stated in SI units are to be regarded as the standard. The values gi

Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact

ASTM D5420-21 通过由重量下降的冲击锤的平坦刚性塑料样品的耐冲击性的标准测试方法（加德纳冲击）

1.1?This test method covers the determination of the relative ranking of materials according to the energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a striker impacted by a falling weight. 1.2?The values stated in S

Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)

EN 17104:2021 建筑物内部使用的热塑性硬质防护墙面覆盖板 性能特征

Thermoplastics rigid protective wallcovering panels for internal use in buildings - Performance characteristics

KS M ISO 6383-2-2020 塑料 薄膜和片材 撕裂强度的测定 第2部分：埃尔门多夫法

Plastics－Film and sheeting－Determination of tear resistance－Part 2：Elmendorf method

T/TANMI 002-2020 塑料双向拉伸（BOP）网

本标准规定了塑料双向拉伸(BOP)网的术语和定义、产品结构标识规格、要求、试验方法、检验规则，以及标志、包装、运输和贮存。 塑料双向拉伸(BOP)网主要应用于农业、园林业集畜牧业，起到防护、美化的作用，要求具有重量轻、强度高、耐腐蚀、颜色多样等优良性能，因此标准从网孔大小、单位面积质量、产品尺寸及拉伸强度四个方面对塑料双向拉伸(BOP)网进行了性能要求。

Plastic biaxially oriented（BOP） net

T/TANMI 001-2020 塑料安全围栏

塑料安全围栏主要用于大型建筑、雪地围栏、事件和人群控制，容易安装使用，便携式、可回收，且原料中添加了荧光（夜光）粉，接受光照5~10min，产品即可在黑暗中可自动发光长达12小时，可以在黑暗中进行安全预警。本标准规定了塑料安全警示网的术语和定义、产品结构标识规格、要求、试验方法、检验规则，以及标志、包装、运输和贮存。标准从网孔大小、单位面积质量、产品尺寸及拉伸强度四个方面对塑料安全围栏进行了性能要求。

Plastic safety fence

T/ZZB 1821-2020 耐冲压耐蒸煮铝箔复合硬片

本文件规定了耐冲压耐蒸煮铝箔复合硬片的缩略语、符号、术语和定义、基本要求、技术要求、试验方法、检验规则及标志、包装、运输、贮存和质量承诺。 本文件适用于经印刷/涂布、复合等工艺制成的耐冲压耐蒸煮铝箔复合硬片（以下简称复合硬片）。

Aluminum foil composite sheet with stamping and boiling resistance

T/ZZB 1776-2020 航空用合金热塑板

本文件规定了航空用合金热塑板的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于以聚氯乙烯和氯化聚氯乙烯为主要原料，添加各类辅料，经成型加工制成的应用于航空客舱系统产品的热塑性合金板（以下简称合金热塑板）。

Thermoplastic alloy sheet for aviation application

T/ZZB 1780-2020 室内装饰用PVC膜

本文件规定了室内装饰用聚氯乙烯膜的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于以聚氯乙烯薄膜为主要原料，经贴合、印刷、压花等工艺加工而成的室内装饰用聚氯乙烯建材装饰膜。

PVC film for Interior decoration

T/ZSA 12-2020 石墨烯改性柔性电热膜

本文件规定了石墨烯改性柔性电热膜的术语和定义、分类和标记、技术要求、试验方法、检验规则、标志、包装、使用说明书、运输及贮存。 本文件适用于建筑取暖供热用石墨烯改性柔性电热膜（以下简称电热膜）。单相电热膜的额定电压不超过 250 V，其他电热膜的额定电压不超过480 V。其他行业的供热用电热膜也可参照使用本文件。

Graphene modified flexible electric heating films

ASTM D5687/D5687M-20 具有标本制备加工指南的扁平复合板制备标准指南

1.1 This guide provides guidelines to facilitate the proper preparation of laminates and test specimens from fiberreinforced organic matrix composite prepregs. The scope is limited to organic matrices and fiber reinforcement in unidirectional (tape) or orthagonal weave patterns. Other forms may require deviations from these general guidelines. Other processing techniques for test coupon preparation, for example, pultrusion, filament winding and resin-transfer molding, are not addressed. 1.2 Specimen preparation is modeled as an 8-step process that is presented in Fig. 1 and Section 8. Laminate consolidation techniques are assumed to be by press or autoclave. This practice assumes that the materials are properly handled by the test facility to meet the requirements specified by the material supplier(s) or specification, or both. Proper test specimen identification also includes designation of process equipment, process steps, and any irregularities identified during processing. 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1 Within the text, the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation

T/CPF 0009-2020 无菌软包装复合膜

对无菌的概念做出定义，对使用范围和要求做出相对应的规范，对需要灭菌的产品做出灭菌方式的要求，对不同灭菌方式可以分类制定技术要求，以及在此灭菌方式下对复合膜的技术要求。

Plastic laminated film using for aseptic packaging

T/CPF 0008-2020 水基型油墨凹版印刷膜、袋

对所使用的水基油墨规定非水组分的比例，以限定厂家滥用水基油墨的名称。对凹版印刷的产品的品质予以规范，以区别于溶剂型油墨印刷的产品；提倡以表印代替里印复合产品，为包装减量化要求做出规范，以利于产品推广应用。

Water based ink for gravure printing film and pouch

T/ZZB 1713-2020 食品包装用塑料与铝箔复合封口膜

本标准规定了复合封口膜的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存、质量承诺等的要求。 本标准适用于使用温度在80 ℃～110 ℃范围内以聚酯薄膜（PET）、聚乙烯薄膜(PE)和铝箔（AL）为基材经干法复合而成的供食品包装用的封口膜。

Plastics and aluminum foil laminated Seal lidding film for food packaging

T/CPF 0010-2020 无溶剂复合膜、袋

对所使用的无溶剂粘合剂、复合产品的可迁移物质提出要求，以区别于溶剂型粘合剂的产品；对无溶剂复合膜/袋的剥离强度、拉断力、尺寸偏差提出要技术要求，质量要求做出规范，以利于产品推广应用。

Solventless laminated film and pouch

T/SLBZSH 01-2020 《多层复合食品包装膜、袋》

缩略语、符号、分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Multilayer composite food packaging film and bag