83.140.10 薄膜和薄板 标准查询与下载

ASTM D8195-18 聚对苯二甲酸乙二醇酯薄膜和薄板规范的标准分类系统和基础

1.1 This standard provides a classification system for tabulating the properties for biaxially oriented polyethylene terephthalate film and sheeting in thicknesses from 1.5 µm to 355 µm. For this classification system, polyethylene terephthalate film and sheeting shall be defined as the material derived from terephthalic acid and ethylene glycol and shall consist of at least 90 % polyethylene terephthalate homopolymer with a typical melting temperature range of 225 °C to 250 °C. This specification does not apply to coated, coextruded, tinted, pigmented, or metallized film or sheeting. This classification (in accordance with D8065/D8065M) is intended to eventually replace Specification D5047 (ref. Note 3). NOTE 1—Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 250 µm. NOTE 2—In order to conform to the original scope of Specification D5047, this classification also includes sheeting up to and including thicknesses of 355 µm. NOTE 3—It is strongly recommended that this classification system be used for all new applications and specifications and that the specification of films referencing Specification D5047 be expeditiously withdrawn or converted to this classification system. 1.2 Polyethylene terephthalate materials, being thermoplastic, are reprocessable and recyclable. This specification allows for the use of those polyethylene terephthalate plastic materials, provided that any specific requirements as governed by the producer and end user are met. 1.3 In all cases where the provisions of this classification system would conflict with a currently referenced ASTM specification for a particular film product, the latter shall take precedence (see Note 3). 1.4 This classification system applies to commercial products and, as such, there is no control over the manufacturing parameters employed in producing the film. It shall be the responsibility of those developing the specification documents utilizing this classification system to identify the critical parameters and values to be used for the cell classifications and suffix requirements. 1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 4—There is no known ISO equivalent to this standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting

PD CEN/TR 17219:2018 塑料 农业和园艺用可生物降解的热塑性地膜 薄膜变化量化指南

Plastics - Biodegradable thermoplastic mulch films for use in agriculture and horticulture - Guide for the quantification of alteration of films

ASTM F3299-18 用电解检测传感器（库仑P2O5传感器）测定塑料薄膜和薄板中水蒸气透过率的标准试验方法

1.1 This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films consisting of single or multilayer synthetic or natural polymers and foils, including coated materials. It provides for the determination of water vapor transmission rate (WVTR). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using an Electrolytic Detection Sensor (Coulometric P2O5 Sensor)

ASTM D5628-18 标准测试方法通过落镖（Tup或Falling Mass）测量扁平硬质塑料样品的抗冲击性

1.1 This test method covers the determination of the threshold value of impact-failure energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a free-falling dart (tup), based on testing many specimens. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. NOTE 1—This test method and ISO 6603-1 are technically equivalent only when the test conditions and specimen geometry required for Geometry FE and the Bruceton Staircase method of calculation are used. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)

DIN EN 13655:2018 塑料 使用后可回收的热塑性地膜，用于农业和园艺；德文版 EN 13655:2018

This document specifies the requirements related to dimensional, mechanical, optical and thermal characteristics of thermoplastic films for mulching applications in agriculture and horticulture, a classification for durability of mulching films and the test methods referred to in this document as well as installation, use and removal conditions of mulch films. These mulch films are intended to be removed after use and not incorporated in the soil.

Plastics - Thermoplastic mulch films recoverable after use, for use in agriculture and horticulture; German version EN 13655:2018

HG/T 5312-2018 窗纱用聚四氟乙烯复合膜

PTFE composite film for window screens

ASTM D2838-18 塑料薄膜和薄片的收缩张力和取向释放应力的标准试验方法

1.1 This test method covers the determination of the shrink tension and related characteristics, that is, shrink force and orientation release stress, of heat-shrinkable plastic film and sheeting of less than 1.0 mm (0.04 in.) thickness. Two procedures are described that permit the measurement of shrink forces at predetermined temperatures. They are as follows: 1.1.1 Procedure A is designed to measure the maximum force exerted by a specimen that is totally restrained from shrinking as it is heated rapidly to a specific temperature. 1.1.2 Procedure B is designed to measure the maximum force exerted by a specimen that is permitted to shrink a predetermined amount prior to restraint while being heated rapidly to a specific temperature. 1.2 Orientation release stress can be determined from the data obtained using Procedure A. 1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 µm (0.010 in.). NOTE 2—There is no known ISO equivalent to this test method. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting

DB13/T 2684-2018 耐蒸煮复合膜、袋通用技术条件

General technical requirements for retort-resistant composite films and bags

EN 13655:2018 塑料.农业和园艺中使用的热塑性覆盖膜

Plastics - Thermoplastic mulch films recoverable after use@ for use in agriculture and horticulture

ASTM D4437/D4437M-16(2018) 用于确定用于连接柔性聚合物片材土工膜的接缝的完整性的无损检测（NDT）的标准实践

1.1 This practice is intended for use as a summary of nondestructive quality control test methods for determining the integrity of seams used in the joining of flexible sheet materials in a geotechnical application. This practice outlines the test procedures available for determining the quality of bonded seams. Any one or combination of the test methods outlined in this practice can be incorporated into a project specification for quality control. These test methods are applicable to manufactured flexible polymeric membrane linings that are scrim reinforced or nonreinforced. This practice is not applicable to destructive testing. For destructive test methods, look at other ASTM standards and practices. 1.2 The types of seams covered by this practice include the following: thermally bonded seams, hot air, hot wedge (or knife), extrusion, solvent-bonded seams, bodied solventbonded seams, adhesive-bonded or cemented seams, taped seams, and waterproofed sewn seams. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Nondestructive Testing (NDT) for Determining the Integrity of Seams Used in Joining Flexible Polymeric Sheet Geomembranes

BS EN 17098-1:2018 塑料 农业和园艺土壤熏蒸消毒用隔离膜 隔离膜规范

What is BS EN 17098-1 - Barrier films used for agriculture about?    BS EN 17098-1 is the first part of an international multi-series standard used for plastics that specifies the test methods, requirements and characteristics of barrier films used for agriculture.  This test method is useful in determining the film permeability and helps in soil disinfection by using the fumigation method.    BS EN 17098-1 specifies the requirements relating to the dimensional, mechanical and physical-chemical characteristics of thermoplastic barrier films designed for agricultural and horticultural soil disinfection by means of fumigation. BS EN 17098-1 also specifies the test methods for verifying these requirements, except the method for determining film permeability using a static technique, which is specified in EN 170982 . BS EN 17098-1 defines also guidance for installation, use and disposal of barrier films.   Note: BS EN 17098-1 is applicable to films used during soil disinfection by fumigation (class 1), and to films used during soil disinfection subsequently kept in situ...

Plastics. Barrier films for agricultural and horticultural soil disinfection by fumigation - Specifications for barrier films

ASTM D7445-18 用泡沫塑料基材（背衬乙烯基侧板）硬质聚（氯乙烯）（PVC）壁板的标准规范

1.1 This specification establishes requirements for vinyl siding with integral foam plastic backing, where the siding is manufactured from rigid PVC compound. Performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance. Methods of indicating compliance with this specification are also provided. NOTE 1—Backed vinyl siding is composed of two major components: the siding and the backing. It is intended that the siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the backing as a separate material, or to the combination of siding and backing as a whole, are also included. 1.2 Backed vinyl siding shall be tested with the backing material in place or removed, as specified in the applicable requirement or test method. 1.3 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4. 1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer’s installation instructions for the specific product to be installed. NOTE 2—Information with regard to siding maintenance shall be obtained from the manufacturer. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. NOTE 3—There is no known ISO equivalent to this standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)

T/SZAS 1-2018 动力锂离子电池用 单向拉伸隔膜 第1部分：厚度均一性

   本标准规定了动力锂离子电池用 单向拉伸隔膜 第1部分：厚度均一性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。    本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Uniaxial stretched separator Part1：Thickness uniformity

T/SZAS 2-2018 动力锂离子电池用 单向拉伸隔膜 第2部分：机械强度

   本标准规定了动力锂离子电池用 单向拉伸隔膜 第2部分：机械强度的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。    本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Uniaxial stretched separator Part2：Mechanical strength

T/SZAS 4-2018 动力锂离子电池用 双向拉伸隔膜 第1部分：厚度均一性

    本标准规定了动力锂离子电池用 双向拉伸隔膜 第1部分：厚度均一性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。     本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Biaxial stretched separator Part1：Thickness uniformity

T/SZAS 6-2018 动力锂离子电池用 双向拉伸隔膜 第3部分：热尺寸稳定性

   本标准规定了动力锂离子电池用 双向拉伸隔膜 第3部分：热尺寸稳定性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存等。    本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Biaxial stretched separator Part3：Thermal dimensional stability

EN 17098-1:2018 塑料 农业和园艺土壤熏蒸消毒用阻隔膜 第1部分：阻隔膜规范

Plastics - Barrier films for agricultural and horticultural soil disinfection by fumigation - Part 1: Specifications for barrier films

T/SZAS 3-2018 动力锂离子电池用 单向拉伸隔膜 第3部分：热尺寸稳定性

   本标准规定了动力锂离子电池用 单向拉伸隔膜 第3部分：热尺寸稳定性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。     本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Uniaxial stretched separator Part3：Thermal dimensional stability

T/SZAS 5-2018 动力锂离子电池用 双向拉伸隔膜 第2部分：机械强度

    本标准规定了动力锂离子电池用 双向拉伸隔膜 第2部分：机械强度的术语和定义、技术要求、测试方法、标识、包装、运输、贮存等。     本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Biaxial stretched separator Part2：Mechanical strength

T/SGX 001-2018 动力锂离子电池用 陶瓷涂覆隔膜 第1部分：热尺寸稳定性

本标准规定了动力锂离子电池用 陶瓷涂覆隔膜 第1部分：热尺寸稳定性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。 本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Ceramic coating separator Part1：Thermal dimensional stability