83.140.10 薄膜和薄板 标准查询与下载

T/SZAS 3-2018 动力锂离子电池用 单向拉伸隔膜 第3部分：热尺寸稳定性

   本标准规定了动力锂离子电池用 单向拉伸隔膜 第3部分：热尺寸稳定性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。     本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Uniaxial stretched separator Part3：Thermal dimensional stability

T/SGX 001-2018 动力锂离子电池用 陶瓷涂覆隔膜 第1部分：热尺寸稳定性

本标准规定了动力锂离子电池用 陶瓷涂覆隔膜 第1部分：热尺寸稳定性的术语和定义、技术要求、测试方法、标识、包装、运输、贮存和注意事项等。 本标准适用于汽车动力、储能等锂离子电池专用隔膜。

Power lithium-ion battery application—Ceramic coating separator Part1：Thermal dimensional stability

EN 17098-2:2018 塑料 农业和园艺土壤熏蒸消毒用阻隔膜 第2部分：使用静态技术测定膜渗透性的方法

Plastics - Barrier films for agricultural and horticultural soil disinfection by fumigation - Part 2: Method for film permeability determination using a static technique

DIN EN 17098-1:2018 塑料. 农业和园艺土壤熏蒸消毒用阻挡膜. 第1部分：阻挡膜规范；德文版本EN 17098-1:2018

This document specifies the requirements relating to the dimensional, mechanical and physical-chemical characteristics of thermoplastic barrier films designed for agricultural and horticultural soil disinfection by means of fumigation.

Plastics - Barrier films for agricultural and horticultural soil disinfection by fumigation - Part 1: Specifications for barrier films; German version EN 17098-1:2018

ASTM D882-18 塑料薄板拉伸性能的标准试验方法

1.1 This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). NOTE 1—Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm (0.010 in.). NOTE 2—Tensile properties of plastics 1.0 mm (0.04 in.) or greater in thickness shall be determined according to Test Method D638. 1.2 This test method can be used to test all plastics within the thickness range described and the capacity of the machine employed. 1.3 Specimen extension can be measured by grip separation, extension indicators, or displacement of gage marks. 1.4 The procedure for determining the tensile modulus of elasticity is included at one strain rate. NOTE 3—The modulus determination is generally based on the use of grip separation as a measure of extension; however, the desirability of using extensometers, as described in 6.2, is recognized and provision for the use of such instrumentation is incorporated in the procedure. 1.5 Test data obtained by this test method is relevant and appropriate for use in engineering design. 1.6 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 4—This test method is similar to ISO 527-3, but is not considered technically equivalent. ISO 527-3 allows for additional specimen configurations, specifies different test speeds, and requires an extensometer or gage marks on the specimen. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile Properties of Thin Plastic Sheeting

ASTM D2578-17 聚乙烯和聚丙烯薄膜润湿张力的标准试验方法

1.1 This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. NOTE 1—This test method and the specified reagents were specifically developed for polyethylene and polypropylene films. It is possible to utilize this test method and the specified reagents for films composed of other polymers, but this can affect the surface energies of the gas-liquid and solid-liquid interfaces, which will affect the contact angle and wetting tension. The applicability and significance for use of non-polyolefin materials must be established by the user. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8. NOTE 2—This test method is equivalent to ISO 8296. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films

ASTM D4551-17 聚氯乙烯（PVC）塑料柔性隐蔽式水密膜的标准规范

1.1 This specification covers poly(vinyl chloride) (PVC) flexible sheeting which is used without mastic, bedding, or coating for construction of concealed water-containmentmembranes in applications where there is potential for costly secondary damage from water leakage and very long-term reliable performance is essential. Examples are fountains, pools, planters, shower and safe pans, tile tubs, or similar wet installations where the membrane is inaccessible once the construction is complete. Included are requirements for materials and sheeting, test methods, workmanship criteria, and methods of marking. 1.2 Recycled materials may be used in this product in accordance with the requirements in Section 5. 1.3 The tests are intended to ensure quality and performance and are not intended for design purposes. Tests have been selected to be conducted primarily with liquids that simulate the environment to which the membrane will be subjected during actual use. 1.4 This specification does not cover water-containment membranes exposed to ultraviolet light. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 There is no known ISO equivalent to this standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane

ASTM D3985-17 用库仑传感器测量透过塑料薄膜和薄片的氧气传输速率的标准试验方法

1.1 This test method covers a procedure for determination of the steady-state rate of transmission of oxygen gas through plastics in the form of film, sheeting, laminates, coextrusions, or plastic-coated papers or fabrics. It provides for the determination of (1) oxygen gas transmission rate (OTR), (2) the permeance of the film to oxygen gas (PO2), and (3) oxygen permeability coefficient (P'O2) in the case of homogeneous materials. 1.2 This test method does not purport to be the only method for measurement of OTR. There may be other methods of OTR determination that use other oxygen sensors and procedures. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor

NF T47-402:2017 工业用无增强橡胶板的分类

Classification des feuilles à base de caoutchouc sans renfort pour usage industriel

ASTM D1830-17 用曲线电极法测定电绝缘用柔性片材的耐热性的标准试验方法

1.1 This test method provides a procedure for evaluating thermal endurance of flexible sheet materials by determining dielectric breakdown voltage at room temperature after aging in air at selected elevated temperatures. Thermal endurance is expressed in terms of a temperature index. 1.2 This test method is applicable to such solid electrical insulating materials as coated fabrics, dielectric films, composite laminates, and other materials where retention of flexibility after heat aging is of major importance (see Note 4). 1.3 This test method is not intended for the evaluation of rigid laminate materials nor for the determination of thermal endurance of those materials which are not expected or required to retain flexibility in actual service. 1.4 The values stated in acceptable metric units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 10.1. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method

DB37/T 3027-2017 唇用化妆品中对位红的测定 高效液相色谱法

Determination of para-red in lip cosmetics by high performance liquid chromatography

ASTM D7193-17 未烧结色素聚四氟乙烯（PTFE）挤出膜或胶带的标准规范

1.1 This specification covers unsintered, pigmented, extruded films or tapes manufactured from polytetrafluoroethylene, in nominal thicknesses from 0.025 mm (0.001 in.) to 0.51 mm (0.020 in.), which are ≥99 % virgin PTFE in composition prior to introducing pigments. NOTE 1—For unsintered non-pigmented products refer to Specification D6585. 1.1.1 The use of recycled PTFE for production of unsintered extruded films or tapes has not been identified at this time. When commercial usable processes and materials are available, this specification will be revised to include recycled materials. 1.2 The values stated in SI units are detailed in IEEE/ASTM SI-10 are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—Although this specification and ISO 13000-1 (1997) and ISO 13000-2 (1997) differ in approach or detail, data obtained relating to specific properties, using either are technically equivalent. NOTE 3—This specification is intended to be a complement to Specification D6585, as the materials covered herein vary significantly enough due to their additives to warrant a stand-alone set of requirements. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape

ASTM D8136-17 使用非接触电容厚度计测定塑料膜厚度和厚度变化的标准测试方法

1.1 This test method covers the determination of the thickness of plastic film, ranging in thickness from 2.5 to 250 µm, with a non-contact thickness gauge that uses capacitance-based technology. It includes a method to generate a series of thickness data points that can be used to characterize the variability patterns of film for both transverse or machine direction (profiling). NOTE 1—Thicker specimens, typically 250 µm to 2500 µm thick, can utilize this test method if the apparatus is designed to measure and handle materials of this thickness range, and the apparatus complies with the requirements as defined in this standard. 1.2 This test method provides a method for buyers and sellers of film to communicate the thickness and pattern of thickness variability of the product they are buying/selling. 1.3 This test method does not apply to textured or porous films or films that are conductive or coated with a conductive substance. NOTE 2—Films that contain excessive levels of anti-static additive can be conductive and need to be tested to verify that they do not cause a negative reading on the instrument. 1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. NOTE 3—There is no known ISO equivalent to this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge

ISO 6179:2017 橡胶 硫化或热塑性橡胶板和橡胶涂层织物 - 挥发性液体透过率的测定（重量分析技术）

Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique)

KS M ISO 15988-2017 塑料 - 膜和片材 - 双轴取向的聚（对苯二甲酸乙二醇酯）（PET）膜

Plastics - Film and sheeting - Biaxially oriented poly(ethyleneterephthalate) (PET) films

KS M ISO 17557-2017 塑料 - 薄膜和片材 - 聚丙烯（PP）薄膜

Plastics - Film and sheeting - Cast polypropylene(PP) films

KS M ISO 15987-2017 塑料 - 薄膜和片材 - 双轴取向的聚酰胺（尼龙）薄膜

Plastics - Film and sheeting - Biaxially oriented polyamide(nylon) films

KS M ISO 17557:2017 塑料 薄膜和薄片 流延聚丙烯（PP）薄膜

Plastics - Film and sheeting - Cast polypropylene(PP) films

KS M ISO 17557-2017(2022) 塑料.薄膜和薄板.浇铸聚丙烯（PP）薄膜

Plastics - Film and sheeting - Cast polypropylene(PP) films

KS M ISO 15988-2017(2022) 塑料.薄膜和薄板.双向取向聚（乙撑苯二甲酸酯）（PET）薄膜

Plastics - Film and sheeting - Biaxially oriented poly(ethyleneterephthalate) (PET) films