83.140.20 层压薄板 标准查询与下载
共找到 275 条与 层压薄板 相关的标准，共 19 页
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
- ICS
- 83.140.20
- CCS
- 发布
- 2005-03-14
- 实施
- 2005-03-14
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 4: Classification and specifications for Compact laminates of thickness 2 mm and greater.
- ICS
- 83.140.20
- CCS
- 发布
- 2005-03-14
- 实施
- 2005-03-14
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information
- ICS
- 83.140.20
- CCS
- 发布
- 2005-03-14
- 实施
- 2005-03-14
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes
- ICS
- 83.140.20
- CCS
- 发布
- 2005-02-12
- 实施
- 2005-02-12
This part of EN 438 applies to laminates less than 2 mm thick normally intended for bonding to supporting substrates to produce HPL composite panels and establishes a classification system for high-pressure decorative laminates according toTheir performance and main recommended fields of application, including materials with special characteristics, for example formability or defined reaction to fire.This part of EN 438 also specifies requirements forThe properties of the various types of laminates covered byThis classification system.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of EN 438 applies to Exterior-grade Compact laminates of thickness 2mm and greater. It specifies requirements for standard and flame-retardant laminates intended for use under outdoor weather conditions such as direct sunlight rain and frost. Two levels of performance are specified; one for moderate exterior conditions, andThe other for severe exterior conditions. Laminates complying withThis part of EN 438 are referred to as Exterior-grade Compact laminates, and are characterized byTheir high tensile strength, high impact resistance,Thermal shock resistance, and resistance to weather and corrosion.They are available in a variety of decorative colours, with high resistance to colour change and aging in outdoor applications. WhenThey are self-supporting Exterior-grade Compact laminates are ready for installation, and only require cutting to size, drilling, etc. to suitThe application. EN 438-2 specifies the methods of test relevant toThis part of EN 438.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 6: Classification and specifications for Exterior-grade Compact laminates of thickness 2 mm and greater
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of EN 438 specifies performance requirements for two types of Compact laminate (defined in Clause 4) of thickness 2 mm or greater intended for interior use.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of EN 438 specifies the methods of test for determination of the properties of high-pressure decorative laminates as defined in Clause 3.These methods are primarily intended for testingThe sheets specified in EN 438-3, 4, 5 and 6.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called Laminates) - Part 2: Determination of properties
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This document specifies the health, safety and energy saving requirements for:? Compact laminate panels/sidings for interior wall and ceiling finishes (including suspended ceilings); ? HPL composite panels/sidings for interior wall and ceiling finishes (including suspended ceilings); ? Compact laminate panels/sidings for exterior wall and ceiling finishes (including suspended ceilings); ? HPL composite panels/sidings for exterior wall and ceiling finishes (including suspended ceilings).
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of EN 438 gives an overview of the standard, and provides guidance inThe selection and application of test methods and specifications contained in Parts 2 to 7 of EN 438.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of EN 438 applies to five classes of flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates, to produce HPL flooring elements. For laminate floor covering applicationsThey meetThe surface property requirements specified in EN 13329.
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates
- ICS
- 83.140.20
- CCS
- 发布
- 2005-01-01
- 实施
This part of ISO 4586 specifies methods of test for determination of the properties of high-pressure decorative laminated sheets as defined in Clause 3. These methods are primarily intended for testing the sheets specified in ISO 4586-1. The precision of the test methods specified in Clauses 4, 7 and 11 of this part of ISO 4586 is not known because inter-laboratory data are not available. When inter-laboratory data are obtained, precision statements will be added to the test methods at the following revision. As all the other test methods have an end point determination based on subjective judgement, it is not meaningful to make a statement of precision in these cases.
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2004-10
- 实施
This part of ISO 4586 establishes a classification system for high-pressure decorative laminated sheets according to their performance and main recommended fields of application, including materials with special characteristics, for example postformability or defined reaction to fire. This part of ISO 4586 also specifies requirements on the properties of the various types of laminate covered by this classification. For several of the properties, more than one test method for checking the requirements is given. These methods have been included to cover cases where the results given by alternative methods are approximately equivalent, where expensive equipment of different types is already in satisfactory use, or where experience is limited to only one of the methods in certain countries. Requirements are specified for those types of material that are most generally used, but additional types may be added as required. The limit values specified apply to the most commonly used types of material, but within each classification it may be possible to obtain variants having much higher performance figures. These materials are characterized by their decorative surfaces, which are relatively hard and resistant to wear, scratching, impact, boiling water, domestic stains and moderate heat. They are intended for interior applications as follows: — thin single-faced laminates usually less than 2mm thick, for bonding to a substrate; — compact laminates, single- or double-faced, approximately 2mm to 5mm thick, which need to be rigidly supported without necessarily being bonded to a substrate; — compact laminates, self-supporting, double-faced, usually thicker than 5mm, the thickness of which will be selected according to application and panel dimensions. The back surface of sheets having only one decorative face is made suitable for adhesive bonding to a substrate. This part of ISO 4586 applies only to decorative laminated sheets as defined in Clause 3. ISO 4586-2 specifies the methods of test relevant to this part of ISO 4586.
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 1: Classification and specifications
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2004-10
- 实施
This guide is intended to aid in the selection of standards for polymer matrix composite materials. It specifically summarizes the application of standards from ASTM Committee D30 on Composite Materials that apply to continuous-fiber reinforced polymer matrix composite materials. For reference and comparison, many commonly used or applicable ASTM standards from other ASTM Committees are also included.1.1 This guide summarizes the application of ASTM standard test methods (and other supporting standards) to continuous-fiber reinforced polymer matrix composite materials. The most commonly used or most applicable ASTM standards are included, emphasizing use of standards of Committee D30 on Composite Materials.1.2 This guide does not cover all possible standards that could apply to polymer matrix composites and restricts discussion to the documented scope. Commonly used but non-standard industry extensions of test method scopes, such as application of static test methods to fatigue testing, are not discussed. A more complete summary of general composite testing standards, including non-ASTM test methods, is included in the Composite Materials Handbook (MIL-HDBK-17). Additional specific recommendations for testing textile (fabric, braided) composites are contained in Guide D 6856.1.3 This guide does not specify a system of measurement; the systems specified within each of the referenced standards shall apply as appropriate. Note that the referenced standards of ASTM Committee D30 are either SI-only or combined-unit standards with SI units listed first.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Guide for Testing Polymer Matrix Composite Materials
- ICS
- 83.140.20
- CCS
- 发布
- 2004-05-01
- 实施
The parameter KTL determined by this test method is a measure of the resistance of a polymer matrix composite laminate to notch-tip damage and effective translaminar crack growth under opening mode loading. The result is valid only for conditions in which the damage zone at the notch tip is small compared with the notch length and the in-plane specimen dimensions. This test method can serve the following purposes. In research and development, KTL data can quantitatively establish the effects of fiber and matrix variables and stacking sequence of the laminate on the translaminar fracture resistance of composite laminates. In acceptance and quality control specifications, KTL data can be used to establish criteria for material processing and component inspection. The translaminar fracture toughness, KTL, determined by this test method may be a function of the testing speed and temperature. This test method is intended for room temperature and quasi-static conditions, but it can apply to other test conditions provided that the requirements of 9.2 and 9.3 are met. Application of KTL in the design of service components should be made with awareness that the test parameters specified by this test may differ from service conditions, possibly resulting in a different material response than that seen in service. Not all types of laminated polymer matrix composite materials experience the contained notch-tip damage and effective translaminar crack growth of concern in this test method. For example, the notch-tip damage may be more extensive and may not be accompanied by any significant amount of effective translaminar crack growth. Typically, lower strength composite materials and those with a significant proportion of reinforcing fibers aligned in a direction perpendicular to the notch axis may not experience the contained notch-tip damage required for a valid test.1.1 This test method covers the determination of translaminar fracture toughness, KTL, for laminated and pultruded polymer matrix composite materials of various ply orientations using test results from monotonically loaded notched specimens. 1.2 This test method is applicable to room temperature laboratory air environments. 1.3 Composite materials that can be tested by this test method are not limited by thickness or by type of polymer matrix or fiber, provided that the specimen sizes and the test results meet the requirements of this test method. This test method was developed primarily from test results of various carbon fiber – epoxy matrix laminates and from additional results of glass fiber – epoxy matrix, glass fiber-polyester matrix pultrusions and carbon fiber – bismaleimide matrix laminates (1-4, 6, 7). 1.4 A range of eccentrically loaded, single-edge-notch tension, ESE(T), specimen sizes with proportional planar dimensions is provided, but planar size may be variable and adjusted, with associated changes in the applied test load. Specimen thickness is a variable, independent of planar size. 1.5 Specimen configurations other than those contained in this test method may be used, provided that stress intensity calibrations are available and that the test results meet the requirements of this test method. It is particularly important that the requirements discussed in 5.1 and 5.4 regarding contained notch-tip damage be met when using alternative specimen configurations. 1.6 The values stated ......
Standard Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials
- ICS
- 83.140.20
- CCS
- G31
- 发布
- 2004
- 实施
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 6: Resistance to wet heat
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2003-02
- 实施
It has long been recognized that dissipation factor and permittivity of laminated insulation as measured in a direction perpendicular to the laminations are not of the same magnitude as those measured parallel to the laminations. This test method provides a means of obtaining data parallel to the laminations where design parameters require this information.1.1 This test method covers the determination of the dissipation factor and permittivity of stiff laminated sheet and plate insulating materials in a direction parallel with the laminations. This test method primarily includes information covering the preparation of the specimen, and details concerning the procedure required to make measurements parallel with the laminations for this particular type of material. The apparatus and general test procedure shall be in accordance with Test Methods D 150.1.2 The values stated in inch-pound units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement see 9.2.
Standard Test Method for Dissipation Factor and Permittivity Parallel with Laminations of Laminated Sheet and Plate Materials
- ICS
- 83.140.20
- CCS
- G31
- 发布
- 2003
- 实施
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 7: Stain resistance and cleanability
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2002-12
- 实施
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 1: Classification and specifications; Amendment 3: Lightfastness
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2002-12
- 实施
High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 3: Lightfastness
- ICS
- 83.140.20
- CCS
- G33
- 发布
- 2002-12
- 实施
