83.140.20 层压薄板 标准查询与下载

ISO 4586-2:1997/Amd 8:2002 装饰用高压叠层板材(HPL).热固性树脂制薄板.第2部分:性能测定.修改件8:尺寸稳定性

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 8: Dimensional stability

ISO 4586-2:1997/Amd 5:2002 高压装饰层压板(HPL).热固性树脂制作的薄板.第2部分:性能测定.修改件5:耐擦伤性

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 5: Resistance to scratching

ASTM D5477-02 傅里叶变换红外线显微光谱法识别聚合物层或夹杂物的标准实施规范

A speck will ultimately cause a failure to occur by virtue of its appearance in a film or by the decrease in electrical or mechanical properties in the polymer substrate (see Specification D 1248). The analysis of composite layers for barrier purposes by microscopic Fourier transform infrared spectroscopy (FT-IR) can indicate the adequacy of the barrier tape or indicate why a barrier may be defective (a missing layer or hole in the layer or poor coextrusion practice). Fig. 1 represents a typical multilayer film. FIG. 1 Position and Function of Materials in Typical Multilayer Films1.1 This practice describes the techniques used for detecting two different polymer entities as follows:1.1.1 Abnormal specks or spots on a surface or in the film that are objectionable as defects and1.1.2 Layers of different polymeric sheets commonly used as barrier films made by coextrusion.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.Note 18212;There is no similar or equivalent ISO standard.

Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR)

ASTM D709-01 层压热固性材料的标准规范

1.1 This specification covers laminated thermosetting materials consisting of two or more plies or layers of reinforcing material bonded by a thermosetting synthetic resin. Examples of such reinforcement are cellulose paper, cotton fabric, glass fabric, and synthetic fiber fabrics. These materials are available in the form of sheets, rolled and molded tubes, and molded rods.1.2 The values stated in inch-pound units are to be regarded as the standard. Note 18212;This specification resembles IEC 60893-3 in title only. The content is significantly different.1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Laminated Thermosetting Materials

ISO 4586-2:1997/Amd 4:2000 装饰用高压层压板 热固性树脂制成的薄板 第2部分:性能测定 修改4:表面耐磨性

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties; Amendment 4: Resistance to surface wear

MS 1504-2000 柔性塑料层压板厚度测定的试验方法

Method of test for determination of thickness for flexible plastics laminates

ASTM D2344/D2344M-00(2006) 用短梁法测定平行纤维组合材料表观层间剪切强度的标准试验方法

In most cases, because of the complexity of internal stresses and the variety of failure modes that can occur in this specimen, it is not generally possible to relate the short-beam strength to any one material property. However, failures are normally dominated by resin and interlaminar properties, and the test results have been found to be repeatable for a given specimen geometry, material system, and stacking sequence (4). Short-beam strength determined by this test method can be used for quality control and process specification purposes. It can also be used for comparative testing of composite materials, provided that failures occur consistently in the same mode (5). This test method is not limited to specimens within the range specified in Section 8, but is limited to the use of a loading span length-to-specimen thickness ratio of 4.0 and a minimum specimen thickness of 2.0 mm [0.08 in.].1.1 This test method determines the short-beam strength of high-modulus fiber-reinforced composite materials. The specimen is a short beam machined from a curved or a flat laminate up to 6.00 mm [0.25 in.] thick. The beam is loaded in three-point bending.1.2 Application of this test method is limited to continuous- or discontinuous-fiber-reinforced polymer matrix composites, for which the elastic properties are balanced and symmetric with respect to the longitudinal axis of the beam.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates

MS 1505-2000 测定柔性塑料层压板粘合强度的试验方法

Method of test for determination of bond strength for flexible plastics laminates

BS 4965:1999 装饰叠层塑料面胶合板和镶板

This British Standard specifies requirements for decorative laminated sheet, based on thermosetting resins, bonded to a substrate, generally for interior use. It specifies the particular combinations of decorative laminate and substrate, generally for interior use. It specifies the particular combinations of decorative laminate, substrate and adhesive necessary to meet the following service conditions: a) in normal humidity conditions with occasional wetting; b) in high humidity conditions with occasional wetting; c) in prolonged high humidity conditions with frequent wetting; d) where, in addition to the above, the board or panel is required to meet statutory fire regulations. The type and grade of laminate required to meet the demands likely to be made on its surface are also specified. NOTE This standard is not applicable to boards and panels manufactured by directly applying uncured films to the substrate and performing cure and bond in the process, nor boards and panels faced with other decorative films such as thermoplastics.

Decorative laminated plastics sheet veneered boards and panels

ASTM E1922-97 层压聚合物基复合材料的层间断裂韧性的标准试验方法

1.1 This test method covers the determination of translaminar fracture toughness, KTL, for laminated polymer matric composite materials of various ply orientations using test results from monotonically loaded notched specimens. 1.2 This test method is applicable to room temperature laboratory air environments. 1.3 Composite materials that can be tested by this test method are not limited by thickness or by type of polymer matrix or fiber, provided that the specimen sizes and the test results meet the requirements of this test method. This test method was developed primarily from test results of various carbon fiber - epoxy matrix laminates and from additional results of glass fiber - epoxy matrix and carbon fiber - bismaleimide matrix laminates (1-4). 1.4 A range of eccentrically loaded, single-edge-notch tension, ESE (T), specimen sizes with proportional planar dimensions is provided, but planar size may be variable and adjusted, with associated changes in the applied test load. Specimen thickness is a variable, independent of planar size. 1.5 Specimen configurations other than those contained in this test method may be used, provided that stress intensity calibrations are available and that the test results meet the requirements of this test method. It is particularly important that the requirements discussed in 5.1 and 5.4 regarding contained notch-tip damage be met when using alternative specimen configurations. 1.6 Values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Translaminar Fracture Toughness of Laminated Polymer Matrix Composite Materials

FD T54-335-1999 装饰层压板（HPL）办公室 HPL 装饰层压板加工指南

Decorative laminated sheets (HPL). Guide for the processing of HPL decorative laminated sheets in offices.

FD T54-337-1999 装饰层压板（HPL）HPL 装饰层压板作为墙纸的加工指南

Decorative laminated sheets (HPL). Guide for the processing of HPL decorative laminated sheets as wallcoverings.

FD T54-336-1999 装饰层压板（HPL）实验室设备用 HPL 装饰层压板的加工指南

Decorative laminated sheets (HPL). Guide for the processing of HPL decorative laminated sheets for laboratory equipment.

JIS K 6903:1998 层压热固高压装饰板

Laminated thermosetting high-pressure decorative sheets

JIS K 6902:1998 层压热固高压装饰板的测试方法

Testing method for laminated thermosetting high-pressure decorative sheets

AS/NZS 2924.1:1998 高压装饰性碾压－热硬化树脂板－分类与规范

Establishes a classification system for high-pressure decorative laminated sheets according to their performance and main recommended fields of application, including materials with special characteristics, for example postformability of defined reaction to fire. Also specifies requirements on the properties of the various types of laminate covered by this classification. For several of the properties, more than one test method for checking the requirements is given. This Standard is identical with and has been reproduced from ISO 4586-1:1995.

High pressure decorative laminates - Sheets made from thermosetting resins - Classification and specifications

AS/NZS 2924.2:1998 高压装饰性碾压－热硬化树脂板－属性定义

Specifies the methods of test for determination of the properties of high-pressure decorative laminated sheets. These methods are primarily intended for testing the sheets specified in AS/NZS 2924.1:1998. This Standard is identical with and has been reproduced from ISO 4586-2:1997.

High pressure decorative laminates - Sheets made from thermosetting resins - Determination of properties

ISO 4586-1:1997 装饰用高压层压板 热固性树脂制成的薄板 第1部分:分类和规范

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 1: Classification and specifications

ISO 4586-2:1997 装饰用高压层压板 热固性树脂制成的薄板 第2部分:性能测定

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties

IPC PE-740A SECTION 13-1997 层压

IPC Standards and Publications are designed to serve the public interest through

Lamination