83.140.20 层压薄板 标准查询与下载

ASTM D6873/D6873M-17 聚合物基复合层压板轴承疲劳响应标准实践

1.1 This practice provides instructions for modifying static bearing test methods to determine the fatigue behavior of composite materials subjected to cyclic bearing forces. The composite material forms are limited to continuous-fiber reinforced polymer matrix composites in which the laminate is both symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2. 1.2 This practice supplements Test Method D5961/D5961M with provisions for testing specimens under cyclic loading. Several important test specimen parameters (for example, fastener selection, fastener installation method, and fatigue force/stress ratio) are not mandated by this practice; however, repeatable results require that these parameters be specified and reported. 1.3 This practice is limited to test specimens subjected to constant amplitude uniaxial loading, where the machine is controlled so that the test specimen is subjected to repetitive constant amplitude force (stress) cycles. Either engineering stress or applied force may be used as a constant amplitude fatigue variable. The repetitive loadings may be tensile, compressive, or reversed, depending upon the test specimen and procedure utilized. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4.1 Within the text the inch-pound units are shown in brackets. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Bearing Fatigue Response of Polymer Matrix Composite Laminates

ASTM D5083-17 使用直边样品的强化热固性塑料的拉伸性能的标准测试方法

1.1 This test method covers the determination of the tensile properties of thermosetting reinforced plastics using test specimens of uniform nominal width when tested under defined conditions of pretreatment, temperature, humidity, and testingmachine speed. NOTE 1—Experience with this test method to date has been limited to glass-reinforced thermosets. Applicability to other materials remains to be determined. 1.2 This test method is used for testing materials of any thickness up to 14 mm (0.55 in.). NOTE 2—This test method is not intended to cover precise physical procedures. It is recognized that the constant-rate-of-crosshead-movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate-of-crosshead movement and rate of strain between gauge marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens that are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed. NOTE 3—Use of this test method for testing materials of thicknesses greater than 14 mm (0.55 in.) is not recommended. Reducing the thickness by machining may be acceptable for materials of uniform reinforcement amount and direction, but is generally not recommended. 1.3 Test data obtained by this test method is relevant and appropriate for use in engineering design. 1.4 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. NOTE 4—This standard and ISO 527-4 address the same subject matter, but differ in technical content. (a) This test method does not include testing of the Type I dogbone shaped specimen described in ISO 527-4. Testing of this type of specimen, primarily used for reinforced and un-reinforced thermoplastic materials, is described in Test Method D638. (b) The thickness of test specimens in this test method includes the 2 mm to 10 mm thickness range of ISO 527-4, but expands the allowable test thickness to 14 mm. (c) ISO 527-4 allows for the use of holes in the tabs of the test specimen while this standard does not. (d) The definitions for tensile strength and modulus differ between these two standards. NOTE 5—For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus > 20-GPa (> 3.0 × 106 -psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M or ISO 527 Part 5.

Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens

GOST R 57921-2017 聚合物复合材料. 试验方法. 通用要求

Polymer composites. Test methods. General requirements

ASTM D709-17 层压热固材料标准规格

1.1 This specification covers laminated thermosetting materials consisting of two or more plies or layers of reinforcing material bonded by a thermosetting synthetic resin. Examples of such reinforcement are cellulose paper, cotton fabric, glass fabric, and synthetic fiber fabrics. These materials are available in the form of sheets, rolled and molded tubes, and molded rods. 1.2 The values stated in inch-pound units are to be regarded as the standard. Note 1: This specification resembles IEC 60893-3 in title only. The content is significantly different. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Laminated Thermosetting Materials

DIN EN 438-2:2016 装饰用高压层压板(HPL).热固性树脂基板材(一般称为层压板).第2部分:性能测定.德文版本EN 438-2-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties; German version EN 438-2:2016

DIN EN 438-5:2016 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第5部分:用于粘结支撑基质的厚度不足2毫米的楼板级层压制件的分类和规范.德文版本EN 438-5-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates; German

DIN EN 438-6:2016 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第6部分:大于和等于2毫米厚的外部用压实层压制件的分类和规范.德文版本EN 438-6-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6 : Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater; German version EN 438-6:2016

DIN EN 438-4:2016 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第4部分:厚度为2毫米和大于2毫米的压实层压制件的分类和规范.德文版本EN 438-4-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater; German version EN 438-4:2016

DIN EN 438-3:2016 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第3部分:用于粘结支撑基质的不足2毫米厚的层压制件的分类和规范.德文版本EN 438-3-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 3: Classification and specifications for laminates less that 2 mm thick intended for bonding to supporting substrates; German version EN 438-

DIN EN 438-1:2016 装饰用高压层压板(HPL).热固性树脂基板材(一般称为层压板).第1部分:说明和一般信息.德文版本EN 438-1-2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 1: Introduction and general information; German version EN 438-1:2016

NF T54-301-2:2016 装饰用高压层压板(HPL).热固性树脂基板材(一般被称为层压板).第2部分:性能测定

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2 : determination of properties

ASTM D3410/D3410M-16e1 具有不支撑规格的聚合物基质复合材料的压缩性能的标准试验方法

1.1 This test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. The composite material forms are limited to continuous-fiber or discontinuous-fiber reinforced composites for which the elastic properties are specially orthotropic with respect to the test direction. This test procedure introduces the compressive force into the specimen through shear at wedge grip interfaces. This type of force transfer differs from the procedure in Test Method D695 where compressive force is transmitted into the specimen by end-loading, Test Method D6641/D6641M where compressive force is transmitted by combined shear and end loading, and Test Method D5467/ D5467M where compressive force is transmitted by subjecting a honeycomb core sandwich beam with thin skins to four-point bending. 1.2 This test method is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pounds units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. NOTE 1—Additional procedures for determining compressive properties of resin-matrix composites may be found in Test Methods D695, D5467/ D5467M, and D6641/D6641M. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading

BS EN 438-5:2016 高压装饰层压板(HPL)基于热固性树脂的板材（通常称为层压板） 用于粘合支撑基材的厚度小于 2 毫米的地板级层压板的分类和规范

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates

BS EN 438-1:2016 高压装饰层压板(HPL)基于热固性树脂的板材（通常称为层压板） 简介和一般信息

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Introduction and general information

BS EN 438-3:2016 高压装饰层压板(HPL)基于热固性树脂的板材（通常称为层压板） 用于粘合支撑基材的厚度小于 2 毫米的层压板的分类和规范

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates

BS EN 438-4:2016 高压装饰层压板(HPL)基于热固性树脂的板材（通常称为层压板） 厚度为 2 毫米及以上的紧凑型层压板的分类和规格

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Classification and specifications for compact laminates of thickness 2 mm and greater

BS EN 438-6:2016 高压装饰层压板(HPL)基于热固性树脂的板材（通常称为层压板） 厚度为 2 毫米及以上的外部级紧凑型层压板的分类和规格

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater

BS EN 438-2:2016 装饰用高压层压板(HPL).热固性树脂基板材(一般称为层压板).性能测定

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Determination of properties

EN 438-4:2016 高压层压装饰制品(HPL).外表基于热固性树脂(通常称为层压制品),第4部分:分类和分层的厚度大于2毫米和更大

This European Standard specifies performance requirements for two types of compact laminate of thickness 2 mm or greater produced by using a high pressure process intended for interior use. High-pressure decorative Compact laminates are characterised by their aesthetic qualities, strength, durability and functional performance. Compact HPL sheets are available in a wide variety of colours, patterns and surface finishes; they are extremely strong, and resistant to wear, impact, scratching, moisture, heat and staining; and possess good hygienic and anti-static properties, being easy to clean and maintain. EN 438-2 specifies the methods of test relevant to this European Standard.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater

EN 438-5:2016 高压层压装饰制品(HPL).外表基于热固性树脂(通常称为层压制品),第5部分:分类和分层厚度小于2毫米用于支撑基板

This European Standard applies to six classes of flooring grade laminates less than 2 mm thick produced by using a high pressure process, intended for bonding to supporting substrates, to produce HPL flooring elements. For laminate floor covering applications they meet the surface property requirements specified in EN 13329. High-pressure decorative flooring laminates are characterised by their high resistance to abrasion, aesthetic qualities and durability. They have good hygienic and anti-static properties and are easy to clean and maintain. The requirements in this document apply only to the high-pressure laminate, and additional properties will need to be specified in order to define the functional performance of the finished flooring product. This European Standard applies only to decorative laminates as defined in Clause 3. EN 438-2 specifies the methods of test relevant to this European Standard.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates