83.140.20 层压薄板 标准查询与下载

ASTM D3917-15a 热固性玻璃钢拉挤型材尺寸公差的标准规格

1.1 This specification defines production tolerances applicable to standard rods, bars, shapes, and flat sheet pultruded from thermosetting glass-reinforced plastics. 1.2 These dimensional tolerances apply to all shapes specified as “standard” by the pultrusion industry. 1.3 Custom shapes and products designed for special applications may carry specific tolerances that vary from the standard. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this standard.

Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes

GOST R 56499-2015 适用于航空玻璃的定向丙烯酸片材. 试验方法

Oriented acrylic sheets focused for aviation glazing. Test methods

GOST R 56500-2015 飞机窗用丙烯酸板. 光学特性的测定方法

Acrylic sheets for aircraft glazing. Methods for determination of optical characteristics

GSO ISO 13894-2:2014 高压装饰层压板 复合元件 第2部分：室内用木质层压板复合元件的规范

This part of ISO 13894 describes the general properties of composite elements surfaced, and possibly edged, with high-pressure decorative laminate (HPDL) as defined in Clause 3. The composite elements specified in this part of ISO 13894 consist of HPDL sheet material adhesively bonded to one or both sides of a wood-based substrate, and are intended for normal interior use. Requirements for special applications, e.g. where the product is subjected to extreme conditions of heat or moisture, are not part of this part of ISO 13894, although Part 1 of this International Standard describes test methods for additional properties which may be applicable to such applications (see ISO 13894-1:2000, Subclause 3.1, Note 3). Test methods and performance levels for special applications shall be agreed between customer and supplier. Information concerning test methods for special applications is given in Annex A.

High-pressure decorative laminates -- Composite elements -- Part 2: Specifications for composite elements with wood-based substrates for interior use

GSO ISO 19712-2:2014 塑料 装饰性固体表面材料 第2部分：性能测定 片材

This part of ISO 19712 specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of sheets. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests may be carried out on finished sheets, but are generally carried out on test specimens of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished sheet.

Plastics - Decorative solid surfacing materials - Part 2: Determination of properties - Sheet goods

DIN EN 438-9:2014 装饰用高压层压板 (HPL). 热固性树脂基板材 (一般称为层压板). 第9部分:可供选择的核心层压板的分类和规范; 德文版本EN 438-9-2010+A1-2013

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 9: Classification and specifications for alternative core laminates; German version EN 438-9:2010+A1:2013

KS M ISO 4586-2-2013(2018) 高压装饰层压板 - 由热固性树脂制成的板材 - 第2部分:性能测定

High-pressure decorative laminates — Sheets made from thermosetting resins — Part 2: Determination of properties

KS M ISO 4586-2:2013 高压装饰板.热固性树脂制薄板.第2部分:性能测定

이 표준은 3.에 규정된 고압 화장판 시트의 물성을 측정하는 시험방법에 대하여 규정한다. 이 방법은KS M ISO 4586-1에 규정된 시트를 시험하고자 작성되었다.이 표준의 4., 7., 11.에 규정된 시험방법의 정밀도는 실험실 간의 자료가 없으므로 알려져 있지 않다.간의 자료가 확보될 때, 다음 개정판에 정밀도에 대한 진술이 추가될 것이다. 다른 모든 시험방법이주관적인 판단에 입각한 최종 측정을 포함하고 있으므로, 이 표준에서 정밀도 설명은 의미가 없다.

High-pressure decorative laminates — Sheets made from thermosetting resins — Part 2: Determination of properties

KS M ISO 4586-2-2013(2023) 高压装饰层压板热固性树脂片材第2部分:性能测定

High-pressure decorative laminates — Sheets made from thermosetting resins — Part 2: Determination of properties

NF T54-301-9:2013 高压装饰性层压板(HPL). 基于热固树胶的薄板材(通常称为层压板). 第9部分: 可替换芯层的分类和规格

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 9: classification and specifications for alternative core laminates

NF T54-301-9/IN1:2013 高压装饰性层压板(HPL). 基于热固树胶的薄板材(通常称为层压板). 第9部分: 可替换芯层的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 9: classification and specifications for alternative core laminates

EN 438-9:2010+A1:2013 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第9部分:代替核心层板的分类和规格 包含修改件A1,2013

This European Standard specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use, the core compositions of which are not covered by EN 438-3 to EN 438-6 and EN 438-8. The core composition types (coloured core and metal reinforced core) are defined in this part of EN 438. EN 438-2 specifies the test methods relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 9: Classification and specifications for alternative core laminates

NF T54-370-3:2013 塑料.实心表面处理用装饰材料.第3部分:性能测定.实心材料表面形状

Plastics - Decorative solid surfacing materials - Part 3: determination of properties - Solid surface shapes

GSO ISO 4586-2:2013 高压装饰层压板 热固性树脂层压板 第2部分：性能测定

This part of ISO 4586 specifies methods of test for determination of the properties of high-pressure decorative laminated sheets as defined in Clause 3. These methods are primarily intended for testing the sheets specified in ISO 4586-1. The precision of the test methods specified in Clauses 4, 7 and 11 of this part of ISO 4586 is not known because inter-laboratory data are not available. When inter-laboratory data are obtained, precision statements will be added to the test methods at the following revision. As all the other test methods have an end point determination based on subjective judgement, it is not meaningful to make a statement of precision in these cases.

High-pressure decorative laminates -- Sheets made from thermosetting resins -- Part 2: Determination of properties

GSO ISO 19712-3:2013 塑料材料 固体装饰表面材料 第3部分：性能测定 固体表面形状

This part of ISO 19712 specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests may be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.

plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes

GSO ISO 4586-1:2013 高压装饰板 热固性树脂板 第1部分：分类和要求

This part of ISO 4586 establishes a classification system for high-pressure decorative laminated sheets according to their performance and main recommended fields of application, including materials with special characteristics, for example postformability or defined reaction to fire. This part of ISO 4586 also specifies requirements on the properties of the various types of laminate covered by this classification. For several of the properties, more than one test method for checking the requirements is given. These methods have been included to cover cases where the results given by alternative methods are approximately equivalent, where expensive equipment of different types is already in satisfactory use, or where experience is limited to only one of the methods in certain countries. Requirements are specified for those types of material that are most generally used, but additional types may be added as required. The limit values specified apply to the most commonly used types of material, but within each classification it may be possible to obtain variants having much higher performance figures. These materials are characterized by their decorative surfaces, which are relatively hard and resistant to wear, scratching, impact, boiling water, domestic stains and moderate heat. They are intended for interior applications as follows: — thin single-faced laminates usually less than thick, for bonding to a substrate; — compact laminates, single- or double-faced, approximately to thick, which need to be rigidly supported without necessarily being bonded to a substrate; — compact laminates, self-supporting, double-faced, usually thicker than , the thickness of which will be selected according to application and panel dimensions. The back surface of sheets having only one decorative face is made suitable for adhesive bonding to a substrate. This part of ISO 4586 applies only to decorative laminated sheets as defined in Clause 3. ISO 4586-2 specifies the methods of test relevant to this part of ISO 4586.

High-pressure decorative laminates - Sheets made from thermosetting resins - Part 1: Classification and specifications

DIN EN ISO 19712-1:2013 塑料.实心表面处理用装饰材料.第1部分:分类和规格(ISO 19712-1-2008).德文版本EN ISO 19712-1-2013

Plastics - Decorative solid surfacing materials - Part 1: Classification and specifications (ISO 19712-1:2008); German version EN ISO 19712-1:2013

DIN EN ISO 19712-2:2013 塑料.实心表面处理用装饰材料.第2部分:性能的测定.薄板材(ISO 19712-2-2007).德文版本EN ISO 19712-2-2013

Plastics - Decorative solid surfacing materials - Part 2: Determination of properties - Sheet goods (ISO 19712-2:2007); German version EN ISO 19712-2:2013

DIN EN ISO 19712-3:2013 塑料.实心表面处理用装饰材料.第3部分:性能测定.实心材料表面形状(ISO 19712-3-2007).德文版本EN ISO 19712-3-2013

Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2007); German version EN ISO 19712-3:2013

DS/EN ISO 19712-1:2013 塑料 装饰性固体表面材料 第1部分：分类和规范

ISO 19712-1:2008 establishes a classification system for solid surfacing materials according to their performance.ISO 19712-1:2008 also specifies property requirements for the various types of solid surfacing materials covered by this classification. Requ

Plastics - Decorative solid surfacing materials - Part 1: Classification and specifications