83.140.20 层压薄板 标准查询与下载

BS EN 438-9:2010+A1:2013 高压装饰性层压板(HPL).基于热固树胶的薄板材(通常称为层压板).可替换芯层的分类和规范

High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates). Classification and specifications for alternative core laminates

EN 438-9:2010 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第9部分:代替核心层板的分类和规格

This European Standard specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use, the core compositions of which are not covered by EN 438-3 [1] to EN 438-6 [4] and EN 438-8 [5]. The core composition types (coloured core and metal reinforced core) are defined inThis part of EN 438. EN 438-2 specifies the test methods relevant toThis part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 9: Classification and specifications for alternative core laminates (Incorporates Amendment A1: 2013)

ASTM D5083-10e1 采用直边样品的热固增强塑料拉伸性能的标准试验方法

4.1 This test method is intended for tensile testing of fiber-reinforced thermosetting laminates. For injection molded thermoplastics, both reinforced and unreinforced, Test Methods D638 is recommended. For most unidirectional fiber reinforced laminates, Test Methods D3039/D3039M is preferred. 4.2 This test method is designed to produce tensile property data for quality control and research and development. Factors that influence the tensile properties, and should therefore be reported, are: material, methods of material and specimen preparation, specimen conditioning, test environment, speed of testing, void content, and volume percent reinforcement. 4.3 It is realized that a material cannot be tested without also specifying the method of preparation of that material. Hence, when comparative tests of materials per se are desired, the greatest care must be exercised to ensure that all samples are prepared in exactly the same way, unless the test is to include the effects of sample preparation. Similarly, for referee purposes or comparisons within any given series of specimen, care must be taken to secure the maximum degree of uniformity in details of preparation, treatment, and handling. Note 6: Preparation techniques for reinforced thermosetting plastics can be found in the part of ISO 1268 appropriate to the manufacturing technique for the laminate. 4.4 Tensile properties may provide useful data for engineering design purposes. However, because of the high degree of sensitivity exhibited by many reinforced plastics to rate of straining and environmental conditions, data obtained by this test method cannot be considered valid for applications involving load-time scales or environments widely different from those of this test method. In cases of such dissimilarity, no reliable estimation of the limit of usefulness can be made for most plastics. This sensitivity to rate of straining and environment necessitates testing over a broad load-time scale (including impact and creep) and range of environmental conditions. Note 7: Since the existence of a true elastic limit in plastics (as in many other organic materials and in many metals) is debatable, the propriety of applying the term “elastic modulus” in its quoted generally accepted definition to describe the “stiffness” or stress-strain characteristics of plastic materials is highly dependent on such factors as rate of application of stress, temperature, previous history of specimen, etc. However, stress-strain curves for plastics, determined as described in this test method, almost always show a linear region at low stresses. A straight line drawn tangent to this portion of the curve permits calculation of an elastic modulus of the usually defined type. Such a constant is useful if its arbitrary nature and dependence on time, temperature, and similar factors are realized. 4.5 For many materials, there may be a specification that requires the use of this test method, but with some procedural modifications that take precedence when adherin......

Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens

LST EN 438-8-2009 高压装饰层压板（HPL） 基于热固性树脂的板材（通常称为层压板） 第8部分：设计层压板的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates

DIN EN 438-8:2009 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第8部分:设计层压制件的分类和规范.英文版本DIN EN 438-8-2009-07

This part of EN 438 specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use with a design effect surface having a phenolic based core and a decorative surface, not covered by EN 438-3 to EN 438-6. Three surface material types (metal, wood veneer and pearlescent decor) are defined in this part of EN 438. EN 438-2 specifies the test methods relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates; English version of DIN EN 438-8:2009-07

SANS 1100:2009 酚醛树脂基工业用层压板

Covers the mechanical and electrical requirements for laminated sheet materials for industrial purposes. The laminated sheets have a cellulose paper-base or a cotton fabric-base and are bonded together under heat and pressure by a therosetting phenolic t

Industrial laminated sheets based on phenolic resin

DS/EN 438-8:2009 高压装饰层压板（HPL） 基于热固性树脂的板材（通常称为层压板） 第8部分：设计层压板的分类和规范

This part of EN 438 specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use with a design effect surface having a phenolic based core and a decorative surface, not covered by EN 438-3 to EN 438-6. Three surface material types (metal, wood veneer and pearlescent decor) are defined in this part of EN 438.EN 438-2 specifies the test methods relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates

NF T54-301-8:2009 基于热固性树脂的高压装饰层压板(通常叫作层压板).第8部分:设计层压板的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called Laminates) - Part 8 : classification and specifications for design laminates.

EN 438-8:2009 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第8部分:设计层压制件的分类和规范

This part of EN 438 specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use with a design effect surface having a phenolic based core and a decorative surface, not covered by EN 438-3 to EN 438-6. Three surface material types (metal, wood veneer and pearlescent decor) are defined inThis part of EN 438. EN 438-2 specifies the test methods relevant toThis part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates

BS EN ISO 19712-1:2013 塑料.固体表面的装饰材料.分类和规范

Plastics. Decorative solid surfacing materials. Classification and specifications

BS ISO 19712-1:2009 塑料 装饰性固体表面材料 分类和规格

Plastics. Decorative solid surfacing materials. Classification and specifications

ANSI/ASTM C582:2009 耐腐蚀设备用接触模压增强热固塑料层压材料的规范

Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment

DS/EN 438-7/ZA:2008 高压装饰层压板（HPL） 基于热固性树脂的板材（通常称为层压板） 第7部分：用于内外墙和天花板饰面的致密层压板和 HPL 复合板

This document specifies the health, safety and energy saving requirements for:• Compact laminate panels/sidings for interior wall and ceiling finishes (including suspended ceilings);• HPL composite panels/sidings for interior wall and ceiling finishes (including suspended ceilings);• Compact laminate panels/sidings for exterior wall and ceiling finishes (including suspended ceilings);• HPL composite panels/sidings for exterior wall and ceiling finishes (including suspended ceilings).It also specifies methods for the evaluation of conformity of the product to the requirements, and includes requirements for marking. It covers only the HPL panels for non-struc

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes

ASTM D4762-08 聚合物基复合材料试验的标准指南

This guide is intended to aid in the selection of standards for polymer matrix composite materials. It specifically summarizes the application of standards from ASTM Committee D30 on Composite Materials that apply to continuous-fiber reinforced polymer matrix composite materials. For reference and comparison, many commonly used or applicable ASTM standards from other ASTM Committees are also included.1.1 This guide summarizes the application of ASTM standard test methods (and other supporting standards) to continuous-fiber reinforced polymer matrix composite materials. The most commonly used or most applicable ASTM standards are included, emphasizing use of standards of Committee D30 on Composite Materials. 1.2 This guide does not cover all possible standards that could apply to polymer matrix composites and restricts discussion to the documented scope. Commonly used but non-standard industry extensions of test method scopes, such as application of static test methods to fatigue testing, are not discussed. A more complete summary of general composite testing standards, including non-ASTM test methods, is included in the Composite Materials Handbook (MIL-HDBK-17). Additional specific recommendations for testing textile (fabric, braided) composites are contained in Guide D 6856. 1.3 This guide does not specify a system of measurement; the systems specified within each of the referenced standards shall apply as appropriate. Note that the referenced standards of ASTM Committee D30 are either SI-only or combined-unit standards with SI units listed first. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Testing Polymer Matrix Composite Materials

ISO 19712-1:2008 塑料.固体表面的装饰材料.第1部分:分类和规范

This part of ISO 19712 establishes a classification system for solid surfacing materials according to their performance. This part of ISO 19712 also specifies property requirements for the various types of solid surfacing materials covered by this classification. Requirements are specified for the types that are most generally used, but additional types may be added as required. The specified limit values apply to the most commonly used types of material, but within each classification it may be possible to obtain variants having much higher performance values. These materials are characterized by their homogeneous appearance, renewable surfaces and inconspicuous seams. They are generally classified as follows. a) Solid surface sheets Solid surfacing sheets are designed for horizontal, vertical, wet and dry applications. b) Solid surface shapes Solid surface shapes include, but are not limited to, kitchen sinks, bathroom sinks, vanity tops, showers, tubs and spas. The important properties of solid surfacing materials are - water resistance, - thermal shock resistance, - heat resistance, - impact resistance, - stain and chemical resistance, - cigarette burn resistance, - colour stability, - hardness, - bacterial and fungal resistance, - cleanability, - hygiene, - seamability, - renewability.

Plastics - Decorative solid surfacing materials - Part 1: Classification and specifications

BS EN ISO 19712-3:2013 塑料. 实心表面处理用装饰材料. 性能的测定. 实心材料表面形状

Plastics - Decorative solid surfacing materials - Determination of properties - Solid surface shapes

BS EN ISO 19712-2:2013 塑料.装饰固体表面材料.性能的测定.薄板材

Plastics - Decorative solid surfacing materials - Determination of properties - Sheet goods

JIS K 6903:2008 叠层热固性高压装饰薄板

この規格は，熱硬化性樹脂高圧化粧板(以下，高圧化粧板という。)について規定する。この規格は，性能及び主用途(材料特性，例えばポストフオーミング性又は火炎反応性を含む)によって，高圧化粧板の種類の体系を規定する。 この規格は，この体系で分類される高圧化粧板の特性についての要求事項を規定する。幾つかのものは，要求特性を確認するためにーつ以上の試験方法がある。この中には，大体同じ結果を与える他の試験方法，高価な試験方法及び国によってはーつだけに限られる試験方法を含む。

Laminated thermosetting high-pressure decorative sheets

JIS K 6902 AMD 1:2008 叠层热固性高压装饰薄板的测试方法(修改件1)

This translation has been made based on the Amendnmnt to the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee based on the provision of Article 12 Clause 2 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 11. Consequently, ,JIS K 6902:2007 is part/ally replaced with this Amendment.

Testing method for laminated thermosetting high-pressure decorative sheets (Amendment 1)

ISO 19712-3:2007 塑料.实心表面处理用装饰材料.第3部分:性能测定.实心材料表面形状

This part of ISO 19712 specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests may be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.

Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes