83.140.20 层压薄板 标准查询与下载

ISO 19712-2:2007 塑料.装饰固体表面材料.第2部分:性能的测定.薄板材

This part of ISO 19712 specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of sheets. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests may be carried out on finished sheets, but are generally carried out on test specimens of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished sheet.

Plastics - Decorative solid surfacing materials - Part 2: Determination of properties - Sheet goods

SANS 1150:2007 玻璃强化聚酯纤维（GRP）层压板（压型或扁平）

Covers 2 types of laminated sheets in both flame-retardant and non-flame-retardant classes. Includes requirements for mass per unit area, light transmission and flammability, and tabulates the size and number of visible defects permitted.

Glass-reinforced polyester (GRP) laminated sheets (profiled or flat)

JIS K 6903:2007 叠层热固性高压装饰薄板

This Standard specifies the laminated thermosetting high-pressure decorative sheets (hereafter referred to as "high-pressure decorative laminates"). This Standard establishes a classification system for high-pressure decorative lami?nates according to their performance and main applications (material characteris?tics, for example, postformability or reaction to fire). This Standard specifies the required items on characteristics of high-pressure decorative laminates classified by this system. For several characteristics, more than one test method for checking the required characteristics is given. Among this, the alternative test method which gives approximately equivalent results, the expensive test method and only one test method in certain countries are included. This Standard specifies the required characteristics of commonly used types, and other types shall be in accordance with the agreement between the parties concerned with delivery. The specified limit values shall apply to high-pressure decorative laminates commonly used, however, higher performance limit values for each classification may be specified in accordance with the agreement between the parties concerned with delivery. The high-pressure decorative laminates shall be characterized by their decora?tive surfaces, which are relatively hard and having resistance to wear, scratch, impact, boiling water, domestic stains and moderate heat, and classified as follows. — Ordinary high-pressure decorative laminate of less than 2 mm thick having thin single-faced laminate to be bonded to substrate — Thick high-pressure decorative laminate of approximately 2 mm to 5 mm thick having single- or double-faced laminate which needs to be rigidly supported but not necessarily be bonded to substrate — Thick high-pressure decorative laminate of more than 5 mm thick having double-faced laminate which does not need to be supported. The thickness shall be selected according to the application and the panel dimensions. The back surface of high-pressure decorative laminate with single-decorated surface shall be made suitable for adhesive bonding to a substrate.

Laminated thermosetting high-pressure decorative sheets

JIS K 6902:2007 叠层热固性高压装饰薄板的测试方法

この規格は，熱硬化性樹脂高圧化粧板(以下，化粧板という。)の試験方法について規定する。

Testing method for laminated thermosetting high-pressure decorative sheets

JIS K 6912 AMD 2 R:2006 叠层热固性薄板材(修改件2)

Laminated thermosetting sheets (Amendment 2)

JIS K 6913 AMD 1:2006 叠层热固性聚合物棒材（修改件1）

Laminated thermosetting rods (Amendment 1)

JIS K 6913:2006 层压热固性聚合物棒材(修改件1)

This translation has been made based on the Amendment to the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with Industrial Standardization Law. Consequently, JIS K 6913:1995 is partially replaced with this Amendment.

Laminated thermosetting rods (Amendment 1)

JIS K 6912 AMD 1:2006 叠层热固性薄板材(修改件1)

Laminated thermosetting sheets (Amendment 1)

ASTM D5449/D5449M-93(2006) 环绕聚合物基复合材料圆柱横向压缩性能的标准试验方法

Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders

BS EN 438-2:2005 装饰用高压层压板(HPL).热固性树脂基板材(一般称为层压板).性能测定

This part of EN 438 specifies the methods of test for determination of the properties of high-pressure decorative laminates as defined in Clause 3. These methods are primarily intended for testing the sheets specified in EN 438-3, 4, 5 and 6. The precision of the test methods specified in Clauses 5, 6, 7, 8, 9, 12, 17, 18, 32 and 33 of this part of EN 438 is not known because inter-laboratory data are not available. When inter-laboratory data are obtained, precision statements will be added to the test methods at the following revision. As all the other test methods have an end point determination based on subjective judgement, it is not meaningful to make a statement of precision in these cases.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Determination of properties

BS EN 438-5:2005 装饰用高压层压板材(HPL).基于热固性树脂的薄板材(通常称为层压板材).用于粘结支撑基质的厚度不足2毫米的楼板级层压板材的分类和规范

This Part of EN 438 applies to five classes of flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates, to produce HPL flooring elements. For laminate floor covering applications they meet the surface property requirements specified in EN 13329. High-pressure decorative flooring laminates are characterised by their high resistance to abrasion, aesthetic qualities and durability. They have good hygienic and anti-static properties and are easy to clean and maintain. The requirements in this document apply only to the high-pressure laminate, and additional properties will need to be specified in order to define the functional performance of the finished flooring product. This Part of EN 438 applies only to decorative laminates as defined in Clause 3. EN 438-2 specifies the methods of test relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Classification and specifications for flooring grade laminates less than 2mm thick intended for bonding to supporting substrates

BS EN 438-6:2005 基于热固性树脂的装饰用高压层压(HPL)薄板材.大于和等于2 mm厚的外部用压实层压板材的分类和规范

This Part of EN 438 applies to Exterior-grade Compact laminates of thickness 2mm and greater. It specifies requirements for standard and flame-retardant laminates intended for use under outdoor weather conditions such as direct sunlight rain and frost. Two levels of performance are specified; one for moderate exterior conditions, and the other for severe exterior conditions. Laminates complying with this Part of EN 438 are referred to as Exterior-grade Compact laminates, and are characterized by their high tensile strength, high impact resistance, thermal shock resistance, and resistance to weather and corrosion. They are available in a variety of decorative colours, with high resistance to colour change and aging in outdoor applications. When they are self-supporting Exterior-grade Compact laminates are ready for installation, and only require cutting to size, drilling, etc. to suit the application. EN 438-2 specifies the methods of test relevant to this part of EN 438.

Decorative high-pressure laminates (HPL) sheets based on thermosetting resins - Classification and specifications for exterior-grade compact laminates of thickness 2mm and greater

BS EN 438-7:2005 装饰用高压层压板材(HPL).基于热固性树脂的薄板材(通常称为层压板材).内墙、外墙和天花板终饰用压实层压板材和HPL复合板材

This document specifies the health, safety and energy saving requirements for: · Compact laminate panels/sidings for interior wall and ceiling finishes (including suspended ceilings); · HPL composite panels/sidings for interior wall and ceiling finishes (including suspended ceilings); · Compact laminate panels/sidings for exterior wall and ceiling finishes (including suspended ceilings); · HPL composite panels/sidings for exterior wall and ceiling finishes (including suspended ceilings). It also specifies methods for the evaluation of conformity of the product to the requirements, and includes requirements for marking. It covers only the HPL panels for non-structural applications, and does not cover fixing systems. The products are intended for use as wall and ceiling finishes for internal and external applications according to the manufacturer's specifications. The scope of this document does not cover: a) overlaid or veneered wood-based panels where the overlay/veneer is not HPL; b) HPL-surfaced wood-based panels intended for use as structural components. These products are covered by EN 13986 (wood-based panels for use in construction). This document covers only characteristics related to health, safety and energy-saving. All other characteristics are covered in separate European Standards for HPL products (see Annex B).

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Compact laminate and HPL composite panels for internal and external wall and ceiling finishes

BS EN 438-3:2005 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第3部分:用于粘结支撑基质的不足2毫米厚的层压制件的分类和规范

This Part of EN 438 applies to laminates less than 2 mm thick normally intended for bonding to supporting substrates to produce HPL composite panels and establishes a classification system for high-pressure decorative laminates according to their performance and main recommended fields of application, including materials with special characteristics, for example formability or defined reaction to fire. This Part of EN 438 also specifies requirements for the properties of the various types of laminates covered by this classification system. High-pressure decorative laminates are characterised by their qualities, durability and functional performance. HPL sheets are available in a wide variety of colours, patterns and surface finishes; they are resistant to wear, scratching, impact, moisture, heat and staining; and possess good hygienic and anti-static properties, being easy to clean and maintain. EN 438-2 specifies the methods of test relevant to this Part of EN 438. Parts 4, 5, etc. of EN 438 are reserved for special types of HPL materials.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Classification and specifications for laminates less than 2mm thick intended for bonding to supporting substrates

BS EN 438-4:2005 装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第4部分:厚度为2毫米和大于2毫米的压实层压制件的分类和规范

This Part of EN 438 specifies performance requirements for two types of Compact laminate (defined in Clause 4) of thickness 2 mm or greater intended for interior use. High-pressure decorative Compact laminates are characterised by their aesthetic qualities, strength, durability and functional performance. Compact HPL sheets are available in a wide variety of colours, patterns and surface finishes; they are extremely strong, and resistant to wear, impact, scratching, moisture, heat and staining; and possess good hygienic and anti-static properties, being easy to clean and maintain. EN 438-2 specifies the methods of test relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Classification and specifications for compact laminates of thickness 2mm and greater

BS EN 438-1:2005 装饰用高压层压板(HPL).热固性树脂基板材(一般称为层压板).说明和一般信息

This Part of EN 438 gives an overview of the standard, and provides guidance in the selection and application of test methods and specifications contained in Parts 2 to 7 of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Introduction and general information

NF T54-301-5:2005 高压装饰性层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第5部分:用于粘结支撑基质的厚度不足2毫米的楼板级层压制件的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually caused laminates) - Part 5 : classification and specifications for flooring grade laminates less than 2 mm thick intended for bonding to supporting substrates.

NF T54-301-1:2005 装饰用高压层压板(HPL).热固性树脂基板材(一般被称为层压板).第1部分:说明和一般信息

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 1 : introduction and general information.

NF T54-301-6:2005 高压装饰性层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第6部分:大于和等于2毫米厚的外部用压实层压制件的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6 : classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater.

NF T54-301-3:2005 高压装饰性层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第3部分:用于粘结支撑基质的不足2毫米厚的层压制件的分类和规范

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 3 : classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates.