83.140.30 塑料管、配件和阀门 标准查询与下载
共找到 536 条与 塑料管、配件和阀门 相关的标准，共 36 页
This document gives requirements and recommendations for the fabrication, installation, inspection and maintenance of GRP piping systems for use in oil and natural gas industry processing and utility service applications. The recommendations apply to delivery, inspection, handling, storage, installation, system pressure testing, maintenance and repair. It is intended to be read in conjunction with ISO 14692-1.
Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 4: Fabrication, installation and operation
- ICS
- 83.140.30
- CCS
- 发布
- 2017-08-17
- 实施
This document gives guidelines for the design of GRP piping systems. The requirements and recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire endurance, spread of fire and emissions and control of electrostatic discharge. This document is intended to be read in conjunction with ISO 14692-1. Guidance on the use of this document can be found in Figure 1, which is a more detailed flowchart of steps 5 and 6 in ISO 14692-1:2017, Figure 1. Figure 1 — Guidance on the use of this document
Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 3: System design
- ICS
- 83.140.30
- CCS
- 发布
- 2017-08-17
- 实施
This document defines the applications, pressure rating methodology, the classification of the products according to application, type of joint and resin matrix and the limitations to both the materials of construction and the dimensions. It also lists the terms, definitions and symbols used and provides guidance in the use and interpretation of ISO 14692-2, ISO 14692-3 and ISO 14692-4. restraining axial thrust from internal pressure, temperature change and fluid hydrodynamic forces and 2) have a trapezoidal shape for its design envelope. It is primarily intended for offshore applications on both fixed and floating topsides facilities, but it can also be used for the specification, manufacture, testing and installation of GRP piping systems in other similar applications found onshore, e.g. produced-water, firewater systems and general industrial use. For floating installations, reference is made to the design, construction and certification standards for the hull or vessel, since these can allow alternative codes and standards for GRP piping associated with marine and/or ballast systems. However, it is recommended that ISO 14692 (all parts) be used for such applications to the maximum degree attainable. caissons, stilling tubes, I-tubes, seawater lift risers and other similar items. Typical oil and gas industry applications for the use of GRP piping and pipelines include those listed in Table 1. Table 1 — Typical current and potential GRP piping oil and gas applications Ballast water Hydrochloric acid Boiler feed water Inert gas Brine Jet-A fuel Carbon Dioxide (CO2) Natural gas Chlorine, gas, wet Oil Condensate (water and gas) (Sour) Oil plus associated gas Cooling water, sweet, brackish, seawater Potable water Demineralised water Process water Diesel fuel Produced water Drains Seawater Emulsions (water-oil-gas mixtures) Service water Fire water (ring main and wet or dry deluge) Sewer (grey and red) Formation water Sodium hydroxide NOTE Some applications, such as wet chlorine gas, hydrogen chloride gas, hydrochloric acid, sodium hydroxide and sodium hypochlorite, require a barrier liner and may require specific corrosion resistant resins. Consult the manufacturer for recommendations. Fresh water Sodium hypochlorite Fuel Sour water Gas (methane, etc.) Unstabilized oil Glycol Vents Hydrocarbon (with or without associated gas) Wastewater Hydrogen chloride gas (HCl) Water disposal Injection water NOTE Some applications, such as wet chlorine gas, hydrogen chloride gas, hydrochloric acid, sodium hydroxide and sodium hypochlorite, require a barrier liner and may require specific corrosion resistant resins. Consult the manufacturer for recommendations.
Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 1: Vocabulary, symbols, applications and materials
- ICS
- 83.140.30
- CCS
- 发布
- 2017-08-17
- 实施
This document gives requirements for the qualification and manufacture of GRP piping and fittings in order to enable the purchase of GRP components with known and consistent properties from any source. It is applicable to qualification procedures, preferred dimensions, quality programmes, component marking and documentation. This document is intended to be read in conjunction with ISO 14692-1.
Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
- ICS
- 83.140.30
- CCS
- 发布
- 2017-08-17
- 实施
本规程适用于新建、改建和扩建的连续纤维增强聚乙烯压力输水管道工程的设计、施工及验收。
Technical specification for continuous fiber reinforced polyethylene pipeline engineering
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-08-08
- 实施
- 2017-10-01
本标准规定了以聚丙烯（PP）树脂为主，加入适量硫酸钙晶须、β-成核剂及其它改性助剂，采用 挤出工艺加工成型的埋地排水排污用改性聚丙烯（PP）双壁波纹管（以下简称PP双壁波纹管）的定义、符号和缩略语、原料、产品分类与标记、管材结构与连接方法、技术要求、试验方法、检验规则和标志、运输、贮存。 本标准适用于长期温度不超过60 ℃的埋地排水排污管道。
Specifications for modified polypropylene (PP) double-wall corrugated pipes for buried drainage and sewage
- ICS
- 83.140.30
- CCS
- Q 22
- 发布
- 2017-07-03
- 实施
- 2017-10-03
HRS pipes for high-rise roof drainage
- ICS
- 83.140.30
- CCS
- G 33
- 发布
- 2017-05-17
- 实施
- 2017-06-17
Small diameter polyethylene (PE) pipes for water supply
- ICS
- 83.140.30
- CCS
- G 33
- 发布
- 2017-05-17
- 实施
- 2017-06-17
本部分规定了以β晶型均聚聚丙烯混配料为原料，经挤出成型的圆形横截面的β晶型均聚聚丙烯管材(以下简称管材)的术语和定义、符号和缩略语、材料、要求、试验方法、检验规则，以及标志、包装、运输、贮存。 本部分适用于输送工业介质管材。
Beta crystallized homopolypropylene (β-PPH) piping systems for industrial application.Part 1:pipes
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本部分规定了以β晶型均聚聚丙烯混配料为原料，经注射成型的β晶型均聚聚丙烯管件(以下简称管件)术语和定义、符号和缩略语、材料、分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本部分适用于输送工业介质管件。
Beta crystallized homopolypropylene (β-PPH) piping systems for industrial application.Part 2:Fittings
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本部分规定了超高分子量聚乙烯(PE-UHMW)管件(以下简称“管件”)的术语和定义、符号和代号、材料、分类、产品规格、要求、试验方法、检验规则，以及标志、包装、运输、贮存。 本部分适用于以PE-UHMW为主要原料，经挤出成型或通过管材二次加工制作的管件。 本部分规定的管件适用于输送浆体、粉体、颗粒状固体、水、45 ℃以下某些腐蚀性化学液体以及低温下的流体。
Ultra-high-molecular-weight polyethylene (PE-UHMW) pipe fittings
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本标准规定了建筑排水用抗冲改性聚氯乙烯(PVC-M)中空壁内螺旋管材(以下简称管材)的术语、定义、符号和缩略语、材料、管材结构与标记、要求、试验方法、检验规则、标志、运输及贮存。 本标准适用于以聚氯乙烯树脂为主要原料，加入必要的抗冲改性等助剂，经挤出成型的建筑排水用立管。
Modified impact resistance poly (vinyl chloride) (PVC-M) hollow-wall inner-spiral pipes for soil and waste discharge inside buildings
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本部分规定了超高分子量聚乙烯(PE-UHMW)管材(以下简称“管材”)的术语和定义、符号、代号和缩略语、分类、材料、产品规格、要求、试验方法、检验规则，以及标志、包装、运输、贮存。 本部分适用于以PE-UHMW为主要原料挤出成型的管材。 本部分规定的管材适用于输送浆体、粉体、颗粒状固体、水、45 ℃以下某些腐蚀性化学液体以及低温下的流体。
Ultra-high-molecular-weight polyethylene (PE-UHMW) pipes
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本标准规定了以砾石/水混合物为磨损介质的塑料管材(以下简称“管材”)耐磨损性试验方法。 本标准适用于热塑性和热固性塑料管材耐磨损性能的评价。 本标准也适用于改性塑料管材以及多层复合塑料管材等耐磨损性能的评价。
Test method for abrasion resistance of plastics pipes
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-04-12
- 实施
- 2017-10-01
本标准规定了 MPE 双壁波纹管的术语和定义、产品分类及标记、管材结构与连接方式、要求、试 验方法、检验规则、标志、运输、贮存。 本标准适用于以改性聚乙烯（MPE）为主要原料，经挤出成型的双壁波纹管，用于输送介质温度在45℃以下的城镇生活排水、工业排水、地表排水以及农田排水。
General technical requirements for MPE double-wall corrugated pipes
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2017-03-30
- 实施
- 2017-04-30
本标准规定了给水用高性能硬聚氯乙烯管材及连接件的材料、产品规格、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于水温不大于45 ℃的室外埋地及管廊内给水用高性能硬聚氯乙烯管材及连接件的制造和检验。
High performance unplasticized poly (vinyl chloride) pipes and fittings for water supply
- ICS
- 83.140.30
- CCS
- G33
- 发布
- 2016-06-14
- 实施
- 2016-12-01
Polyethylene fittings for use with polyethylene pies for the supply of gaseous fuels－Metric series－Specifications－Part 2：Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings
- ICS
- 83.140.30
- CCS
- 发布
- 2016-01-06
- 实施
Polyethylene fittings for use with polyethylene pies for the supply of gaseous fuels－Metric series－Specifications－Part 2：Spigot fittings for butt fusion, for socket fusion using heated tools and for u
- ICS
- 83.140.30
- CCS
- 发布
- 2016-01-06
- 实施
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels－Metric series－Specifications－Part 3：Electrofusion fittings
- ICS
- 83.140.30
- CCS
- 发布
- 2016-01-06
- 实施
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels－Metric series－Specifications－Part 3：Electrofusion fittings
- ICS
- 83.140.30
- CCS
- 发布
- 2016-01-06
- 实施
