83.140.99 其他橡胶和塑料制品 标准查询与下载

T/SLEA 0031.3-2022 实验室用水气配件技术规范 第3部分：水槽

本文件规定了实验室用水槽的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输、贮存、安装指南、使用与维护以及故障排除。 本文件适用于实验室用聚丙烯水槽。 (说明：标准中的CCS号是按照监管局系统中使用的"中国标准文献分类号"定的，本平台数据库中所用的分类号为2017版的国民经济行业分类号，两边系统中分类号不一致，在本平台中上传时，重新按照本平台的分类号选择的，故下载标准文本后会看到CCS号与在本系统中选择的分类号不一致的情况)

Technical requirements for laboratory water and gas fittings Part 3: Sink

ASTM D5336-22 聚邻苯二甲酰胺（PPA）注射成型材料规范的标准分类系统和基础

1.1 This classification system covers polyphthalamide (PPA) materials suitable for injection molding. 1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5. 1.3 This classification system allows for the use of recycled materials provided that all specification requirements are met. 1.4 This classification system is intended to be a means of calling out plastics materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.5 The values stated in SI units are to be regarded as the standard (see IEEE/ASTM SI-10). The values given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 11.7.1. NOTE 1—There is no known ISO equivalent to this standard. ISO 16396-1 ⁄-2 for polyamides may also be used to describe and classify these PPA materials, but the technical content is significantly different. NOTE 2—ASTM Standard D6779 on polyamide materials also includes PPA materials in its coverage of various polyamide chemistries. This standard gives additional information for classification and specification for PPA compositions classified as Group 10 (PA6T/66), Group 12 (PA6T/6I/66) and Group 13 (PA6T/6I) in ASTM Standard D6779 and includes provisions for other PPA compositions to utilize the classification presented. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials

ASTM D1562-22 纤维素丙酸酯模制和挤压化合物

1.1 This classification system covers requirements for plasticized cellulose acetate propionate thermoplastic compounds suitable for injection molding and extrusion. These compounds have a propionyl content less than 48 % and an acetyl content less than 3 % and can contain dyes and pigments. Cellulosic plastic materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those cellulosic materials, provided that all specific requirements of this classification system are met. 1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are specified by using the suffixes as given in Section 5. 1.3 This classification system and subsequent line call out specification are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and performance required of the part, environment to which it will be exposed, fabrication process to be employed, costs involved, and inherent properties of the material other than those covered by this classification system. 1.4 The values stated in SI units are to be regarded as standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)

T/CSTM 00541-2022 灭火用直升机挂载吊桶

本文件规定了灭火用直升机挂载吊桶（以下简称“灭火吊桶”）的结构和材料、要求、检验规则、标志、包装、运输、贮存和寿命；描述了灭火吊桶的结构以及试验方法。 本文件适用于以橡胶涂覆织物为桶体材料的灭火吊桶。

Helicopter external mount buckets for firefighting

T/QGCML 342-2022 服装用商标辅料通用技术规范

本标准规定了服装用商标辅料通用技术规范的术语定义、技术要求、试验方法、检验规则、标志、包装、运输及储存。 本标准适用于服装用商标辅料。

General technical specification for trademark accessories for clothing

T/MYXZX 004-2022 食品用聚乙烯吹塑瓶

食品用聚乙烯吹塑瓶的原料、要求、试验方法、检验规则、标志、包装、运输和贮存。

Polyethylene blow molded bottle for food

T/GMPA 11-2022 聚氯乙烯(PVC)装饰膜

本文件规定了聚氯乙烯(PVC)装饰膜的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本文件适用于以聚氯乙烯为主要原料，经压延、贴合、印刷、压花等工艺加工而成的聚氯乙烯装饰膜。

Polyvinyl chloride（PVC）sheet for ornament

ASTM D3294-22 聚四氟乙烯树脂模压板和模压基本形状的标准规范

1.1 This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of 0.794 mm (1⁄32 in.) manufactured from PTFE resin molding materials defined in Specification D4894. 1.2 This specification also establishes requirements for molded basic shapes made from molding materials. This specification is for products 300 mm (12 in.) or less in a dimension parallel to and 12.7 mm (0.5 in.) or greater in the dimension perpendicular to the direction of the applied molding pressure. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Special attention is called to 13.2, 13.3, 13.6, 13.8, and A1. NOTE 1—There is no known ISO equivalent to this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes

T/ZZB 2772-2022 农用塑料经编遮阳网

本文件规定了农用塑料经编遮阳网的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于以高密度聚乙烯（HDPE）树脂为主要原料，添加抗老化剂和色母粒等，经挤出、拉伸、定型成圆丝或扁丝，以针织或平织工艺编织而成的农用塑料经编遮阳网（以下简称“遮阳网”）。

Plastic knitting sunshade net for agriculture

T/ZZB 2754-2022 聚乙烯编织覆膜篷布

本文件规定了聚乙烯编织覆膜篷布的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于以聚乙烯编织布为基布，背面流延复合聚乙烯膜，正面流延聚乙烯膜作为粘合层与聚乙烯吹塑薄膜复合，经热合加工制成的聚乙烯编织覆膜篷布（以下简称篷布）。 本文件适用于单位面积平均质量为181 g/m2～300 g/m2的篷布。

Polyethylene woven tectorial membrane tarpaulins

GSO ISO 10282:2022 一次性无菌橡胶手术手套 规格

ISO 10282:2014 specifies requirements for packaged sterile rubber gloves intended for use in surgical procedures to protect the patient and the user from cross-contamination. It is applicable to single-use gloves that are worn once and then discarded. It does not apply to examination or procedure gloves. It covers gloves with smooth surfaces and gloves with textured surfaces over part or the whole glove. ISO 10282:2014 is intended as a reference for the performance and safety of rubber surgical gloves. The safe and proper usage of surgical gloves and sterilization procedures with subsequent handling, packaging, and storage procedures are outside the scope of ISO 10282:2014.

Single-use sterile rubber surgical gloves — Specification

T/GZHG 030-2022 无水磷石膏改性高密度聚乙烯双壁波纹排水管

4.7  性能指标  管材的物理力学性能应符合表3的规定。 表3  管材的物理力学性能 项  目　指  标 环刚度/（kN/㎡）　SN8　≥8 　SN10　≥10 　SN12.5　≥12.5 落锤冲击试验　10/10通过 环柔性　试样圆滑，无反向弯曲，无破裂，两壁无脱开 烘箱试验　无气泡、无分层、无开裂 蠕变比率/%　≤4 氧化诱导时间/min　≥20 5  试验方法 5.1  状态调节和试验环境 试样在温度（23±2）℃，相对湿度为（50±2）%条件下进行调节和试验，状态调节时间不应少于24 h。内径公称尺寸大于600mm的管材，状态调节时间不应少于48 h。 5.2  外观、尺寸测量 5.2.1  外观 按GB/T 19472.1-2019中8.2规定进行。 5.2.2  尺寸 管材有效长度、平均外径、平均内径、壁厚、接合长度、承口平均内径、承口壁厚的测量按GB/T 8806-2008规定进行。 5.3  抗拉强度 按 GB/T1040.2-2006规定进行。 5.4  弯曲模量 按GB/T9341-2008规定进行。 5.5  熔体质量流动速率 按GB/T3682.1-2018规定进行。 5.6  环刚度 按GB/T 9647-2015规定进行。 5.7  落锤冲击试验 按GB/T 14152-2001规定进行。 5.8  环柔性 按GB/T 39385-2020规定进行。 5.9  烘箱试验 按GB/T 19472.1-2019规定进行。 5.10  蠕变比率 按GB/T 18042-2000规定进行。 5.11  氧化诱导时间 按GB/T 19466.6-2009规定进行。 6   检验规则 6.1  组批 同一批原料，同一配方和工艺条件下生产同一规格套管为一批，管材内径≤500 mm 时，每批数量 不超过 60 t，如生产数量少，生产期 7 d尚不足 60 t，则以 7 d产量为一批。管材内径＞500 mm 时，每批数量不超过 300 t，如生产数量少，生产期 30 d尚不足 300 t，则以 30 d产量为一批。 6.2  出厂检验 6.2.1  出厂检验项目为环刚度、环柔性、烘箱试验、落锤冲击试验和 氧化诱导时间。 6.2.2  抽样按GB/T 2828.1-2012的规定进行，采用一次正常抽样方案，取一般检查水平I，合格质量水平 (AQL) 为6.5，抽样方案见表4。 表4  抽样方案 单位为根 批量 （N）　样本量 （n）　接收数 （Ac）　拒收数 （Re） ≤150　8　1　2 151～300　13　2　3 301～500　20　3　4 501～1200　32　5　6 1201～3200　50　7　8 3201～10000　80　10　11 6.2.3  在按6.2.2抽样检查合格的样品中，随机抽查样品，进行的环刚度、环柔性和落锤冲击试验；并按5.2.1要求随机抽取3个样，对层压壁厚进行测量，取最小值。 6.3  型式检验   型式检验项目为4.5、4.6、4.7中的全部项目。一般情况下一年至少一次。若出现下列情况之一时，亦应进行型式检验。 a）结构、材料、工艺有较大变动可能影响产品性能时； b）设备改造后或大型维修后恢复生产时； c）产品长期停产后恢复生产时； d）出厂检验结果与上次型式检验的结果有较大差异时。 6.4  判定规则 4.5、4.6、4.7项目中除层压壁厚外，任一项不符合表4规定时，则判断为不合格。层压壁厚、环刚度、环柔性、落锤冲击试验有一项达不到指标时，按6.2.2抽取的合格样品中再抽取双倍样品进行该项的复检。如仍不合格，判该批为不合格批。 7  标志、运输和贮存  7.1  标志 每根套管在波峰上至少有一处永久性标志，标志内容应包括产品名称、材料代号、公称尺寸、环刚度等级、执行标准、生产厂名（厂名可缩写）、生产日期。 7.2  运输 产品在装卸运输时，不得受剧烈撞击、抛摔和重压，应使用专用管枕进行堆放、运输。 7.3  贮存 管材存放场地应平整，堆放应整齐，堆放高度不得超过4 m，远离热源，不得露天存放、曝晒。

Anhydrous phosphogypsum modified high-density polyethylene double-wall corrugated drainage pipe

ASTM D7336/D7336M-22 蜂窝夹芯材料静态能量吸收性能的标准试验方法

1.1 This test method determines the static energy absorption properties (compressive crush stress and crush stroke) of honeycomb sandwich core materials. These properties are usually determined for design purposes in a direction normal to the plane of the face sheets (also referred to as the facing plane) as the honeycomb core material would be placed in a structural sandwich construction. 1.2 Permissible core materials are limited to those in honeycomb form. 1.3 This test method is not intended for use in crush testing of stabilized honeycomb core materials (for which the facing plane surfaces of the honeycomb core material are dipped in resin to resist local crushing) or sandwich specimens (for which facings are bonded to the honeycomb core material). 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4.1 Within the text, the inch-pound units are shown in brackets. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Static Energy Absorption Properties of Honeycomb Sandwich Core Materials

DB37/T 5121-2022 室外塑胶跑道质量控制技术规程

本规程适用于山东省新建、扩建和改建的教学、竞赛和健身用室外塑胶跑道的设计、选材、施工、验收和管理维护，其他的塑胶跑道根据材料类型和施工工艺参照本规程执行。

Technical specification for quality control of outdoor plastic track

T/ZZB 2681-2022 家用塑料宠物屋

本文件规定了家用塑料宠物屋的术语和定义、分类型号、基本要求、技术要求、试验方法、检验规则、标志、包装、 运输、贮存及质量承诺。 本文件适用于体重50 kg及以下宠物狗、 猫居住的，以聚丙烯树脂（PP） 为主要原料， 经注塑或吹塑成型、 装配而成的家用塑料宠物屋。

Household plastic pet house

T/CBMF 173-2022 反应型复合止水带

本文件规定了反应型复合止水带的分类和标记、一般要求、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于安装于混凝土结构变形缝、施工缝部位中埋式或背贴式反应型复合止水带。

Reactive composite waterstop

T/GMPA 10-2022 聚氯乙烯(PVC)运动地板胶

本文件规定了聚氯乙烯（PVC）运动地板胶的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 

Polyvinyl chloride（PVC）sports rubber floor

T/ZZB 2656-2022 便携式塑料餐盒

本文件规定了便携式塑料餐盒（以下简称：餐盒）的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于内胆层以聚亚苯基砜树脂（PPSU）为主要原料，其他配件以聚丙烯（PP）和硅橡胶为原料，经加工制成的便携式塑料餐盒。

Portable plastic containers for food

ASTM D7290-06(2022) 土木工程结构用聚合物复合材料材料性能特征值评估的标准实施规程

1.1 This practice covers the procedures for computing characteristic values of material properties of polymeric composite materials intended for use in civil engineering structural applications. The characteristic value is a statistically-based material property representing the 80 % lower confidence bound on the 5th-percentile value of a specified population. Characteristic values determined using this standard practice can be used to calculate structural member resistance values in design codes for composite civil engineering structures and for establishing limits upon which qualification and acceptance criteria can be based. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications

ASTM D1201-13(2022)e1 热固性聚酯模塑化合物的标准规范

1.1 This specification covers compression molding, thermosetting, unsaturated polyester molding compounds as further defined in 3.1. 1.2 The values stated in SI units are to be regarded as the standard. NOTE 1—The properties included in this specification are those required to identify the types of molding compounds covered. There may be other requirements necessary to identify particular characteristics. These will be added to the specification as their inclusion becomes generally desirable and the necessary test data and methods become available. NOTE 2—ISO 3672–1: 1979(E) is similar but not equivalent to this specification. Product classification and characterization are not equivalent. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermosetting Polyester Molding Compounds