83.200 橡胶和塑料工业设备 标准查询与下载

DIN EN ISO 483:2006 塑料.为保持恒定湿度使用水溶液进行调节和试验用的小型密封容器(ISO 483-2005).德文版本 EN ISO 483-2005

The document establishes guidelines for the construction and use of enclosures with volumes less than 200 dm3, in order to obtain atmospheres of constant relative humidity at given temperatures, using saturated aqueous salt solutions, glycerol/water solutions of sulfuric acid/water solutions, for conditioning and testing plastics. It specifies the procedures to be followed to maintain the relative humidities of the conditioning and testing atmospheres within the required tolerances, at the temperatures specified by particular International Standards.#,,#

Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value (ISO 483:2005); English version of DIN EN ISO 483:2006-02

BS EN ISO 483:2006 塑料.使用水溶液进行调节和试验保持恒定湿度的小型密封容器

This International Standard establishes guidelines for the construction and use of enclosures with volumes less than 200 dm3, in order to obtain atmospheres of constant relative humidity at given temperatures, using saturated aqueous salt solutions, glycerol/water solutions or sulfuric acid/water solutions, for conditioning and testing plastics. It specifies the procedures to be followed to maintain the relative humidities of the conditioning and testing atmospheres within the required tolerances, at the temperatures specified by particular International Standards. The procedures described are intended for conditioning small quantities of materials prior to test, and for such tests as may be carried out entirely within a small enclosure, e.g. electrical tests. The guidelines described do not apply to enclosures requiring frequent opening.

Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at constant value

BS EN ISO 483:2005 塑料 小型外壳 用于使用水溶液进行调节和测试 以将湿度保持在恒定值

1   Scope This International Standard establishes guidelines for the construction and use of enclosures with volumes less than 200 dm 3 , in order to obtain atmospheres of constant relative humidity at given temperatures, using saturated aqueous salt solutions, glycerol/water solutions or sulfuric acid/water solutions, for conditioning and testing plastics. It specifies the procedures to be followed to maintain the relative humidities of the conditioning and testing atmospheres within the required tolerances, at the temperatures specified by particular International Standards. The procedures described are intended for conditioning small quantities of materials prior to test, and for such tests as may be carried out entirely within a small enclosure, e.g. electrical tests. The guidelines described do not apply to enclosures requiring frequent opening.

Plastics. Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at constant value

NF T51-913*NF EN ISO 483:2006 塑料.使用水溶液以保持恒定相对湿度值的调节和试验用小型密封容器

Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain relative humidity at a constant value.

ASTM D957-06 塑料生产用模型表面温度测定的标准实施规程

The properties of molded parts and the ease of producing satisfactory specimens are influenced by the temperature of the mold. It is desirable to know the actual mold temperature which may be different from the mold temperature control medium. The user should be aware of temperature differences across the mold/thermocouple interface and at leads and should take precautions to minimize such differences.1.1 This practice is intended for determining the temperature at a specified point or points on the surface of the cavity and base of a mold for plastics. By determining the temperature at as many points as deemed necessary, the overall temperature condition of the surface can be determined.1.2 The values stated in SI units are to be regarded as standard. The values in brackets are given for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1There is no similar ISO standard.

Standard Practice for Determining Surface Temperature of Molds for Plastics

ISO 483:2005 塑料.用于使用水溶液进行调节和试验保持恒定湿度的小型密封容器

This International Standard establishes guidelines for the construction and use of enclosures with volumes less than 200 dm3, in order to obtain atmospheres of constant relative humidity at given temperatures, using saturated aqueous salt solutions, glycerol/water solutions or sulfuric acid/water solutions, for conditioning and testing plastics. It specifies the procedures to be followed to maintain the relative humidities of the conditioning and testing atmospheres within the required tolerances, at the temperatures specified by particular International Standards. The procedures described are intended for conditioning small quantities of materials prior to test, and for such tests as may be carried out entirely within a small enclosure, e.g. electrical tests. The guidelines described do not apply to enclosures requiring frequent opening.

Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value

JB/T 5416-2005 塑料挤出干法热切造粒辅机

本标准规定了塑料挤出干法热切造粒辅机(以下简称切粒机)的规格与基本参数、要求、试验方法和检验规则、标志、包装、运输和贮存等。 本标准适用于聚氯乙烯、高填充塑料母粒、亲水性物料和非粘性物料等适于干法热切的物料的风冷、水环、水雾形式的干法热切造粒辅机。 本标准不适用于非塑料挤出干法热切造粒辅机。

Hot pelletizing machinery for extruded plastics by dry method

EN ISO 483:2005 塑料.为保持恒定湿度使用水溶液进行调节和试验用的小型密封容器 ISO 483-2005

Plastics - Small Enclosures for Conditioning and Testing Using Aqueous Solutions to Maintain the Humidity at a Constant Value

NF E63-606:2004 塑料和橡胶加工机械.压力机.安全要求

Plastics and rubber machines - Presses - Safety requirements.

JB/T 5289-2004 鞋用转盘注射成型机

本标准规定了鞋用转盘注射成型机的型号、型式与基本参数、技术要求、试验方法、检验规则和标志、包装、运输、贮存。

Rqtating injection mould machine for shoes making

JB/T 10464-2004 拉条式塑料切粒机

本标准规定了拉条式塑料切粒机的规定与基本参数、要求、试验方法和检验规则、标志、包装、运输和贮存等。 　　本标准适用于塑料用拉条式塑料切粒机。 　　本标准不适用于非塑料挤出拉条切粒型式的其他类型的切粒机。

Stranding plastics pelletizer

JB/T 7267-2004 塑料注射成型机

本标准规定了塑料注射成型机的型号、基本参数、要求、试验方法、检验规则以及标志、包装、运输、储存。 本标准适用于热塑性、单螺杆、单工位、卧式塑料注射成型机。

Plastic injection moulding machine

JB/T 7669-2004 塑料混合机

本标准规定了塑料混合机的基本参数、技术要求、试验方法、检验规则以及标志、包装、运输及贮存。 本标准适用于混合塑料原料的热混合机和冷混合机(立式冷混合机、卧式冷混合机),以下简称热机、立冷、卧冷。

Plastics mixering machines

BS EN 289:2004 塑料和橡胶机械.压力机.安全要求

This document specifies the essential safety requirements for hydraulic presses, including toggle and hydro-mechanic ones, with a vertical closing movement more than 6 mm for the moulding of plastics and/or rubber. This document covers both compression moulding (see 3.1.1) and transfer moulding (see 3.1.2). All hazards listed in clause 4 are covered by this document. The following machines are excluded: — injection moulding machines (see EN 201); — presses for curing pneumatic tyres; — presses for curing inner tubes and curing bags; — hydraulic presses as covered by EN 693; — mechanical presses as covered by EN 692; — thermoforming machines (see EN 12409); — RIM machines (see EN 1612-1 and EN 1612-2). The safety requirements for the additional hazards arising from the interaction between presses and ancillary equipment especially loading and unloading devices are specified. The safety requirements for the ancillary equipment itself are not specified. This document does not cover: — the requirements of Directive 94/9/CE concerning equipment and protective systems intended for use in potentially explosive atmospheres; — requirements for the design of exhaust ventilation systems. This document is not applicable to presses manufactured before the date of publication of this document by CEN.

Plastics and rubber machines - Presses - Safety requirements

BS EN 289:2004+A1:2008 塑料机和橡胶机.压力.安全要求

This document specifies the essential safety requirements for hydraulic presses, including toggle and hydromechanic ones, with a vertical closing movement more than 6 mm for the moulding of plastics and/or rubber. This document covers both compression moulding (see 3.1.1) and transfer moulding (see 3.1.2). All hazards listed in clause 4 are covered by this document. The following machines are excluded: ? injection moulding machines (see EN 201); ? presses for curing pneumatic tyres; ? presses for curing inner tubes and curing bags; ? hydraulic presses as covered by EN 693; ? mechanical presses as covered by EN 692; ? thermoforming machines (see EN 12409); ? RIM machines (see EN 1612-1 and EN 1612-2). The safety requirements for the additional hazards arising from the interaction between presses and ancillary equipment especially loading and unloading devices are specified. The safety requirements for the ancillary equipment itself are not specified. This document does not cover: ? the requirements of Directive 94/9/CE concerning equipment and protective systems intended for use in potentially explosive atmospheres; ? requirements for the design of exhaust ventilation systems. This document is not applicable to presses manufactured before the date of publication of this document by CEN.

Plastics and rubber machines - Presses - Safety requirements

EN 289:2004 塑料和橡胶机械.压榨机.合并修改件A1的安全性要求

This document specifies the essential safety requirements for hydraulic presses, including toggle and hydromechanic ones, with a vertical closing movement more than 6 mm for the moulding of plastics and/or rubber. This document covers both compression moulding (see 3.1.1) and transfer moulding (see 3.1.2). All hazards listed in clause 4 are covered by this document. The following machines are excluded: ? injection moulding machines (see EN 201); ? presses for curing pneumatic tyres; ? presses for curing inner tubes and curing bags; ? hydraulic presses as covered by EN 693; ? mechanical presses as covered by EN 692; ? thermoforming machines (see EN 12409); ? RIM machines (see EN 1612-1 and EN 1612-2). The safety requirements for the additional hazards arising from the interaction between presses and ancillary equipment especially loading and unloading devices are specified. The safety requirements for the ancillary equipment itself are not specified. This document does not cover: ? the requirements of Directive 94/9/CE concerning equipment and protective systems intended for use in potentially explosive atmospheres; ? requirements for the design of exhaust ventilation systems. This document is not applicable to presses manufactured before the date of publication of this document by CEN.

Plastics and rubber machines - Presses - Safety requirements Incorporates Amendment A1: 2008

BS EN 13418+A1:2004 橡胶和塑料机械 薄膜和薄板的卷切机 安全要求

Plastics and rubber machines. Winding machines for film or sheet. Safety requirements

BS EN 13418:2004 橡胶和塑料机械.薄膜和薄板的卷切机.安全要求

This European Standard specifies the safety requirements for the design and construction of winding, unwinding and rewinding machines for film or sheet manufactured from rubber, plastics and composite materials in respect of the significant hazards listed in clause 4. A winding machine begins at the intake of the film or sheet into the winding machine and ends at the discharge position of the reel(s). An unwinding machine begins at the take-up position of the reel(s) and ends at the film or sheet take-off point. A rewinding machine begins at the take-up position of the reel(s) and ends at the discharge position of the reel(s). In some machines the winding, unwinding and rewinding functions may be combined. The following functional groups are covered by this European Standard: — fixed point roll; — film or sheet tension control; — winding zone; — reel change device; — reel loading and unloading devices; and the following additional equipment integrated into the winding machine: — spreader roll device; — longitudinal cutting unit; — slitting device; — film or sheet alignment device; — static eliminator. Technical safety requirements for the design and construction of aids for lifting and handling, e.g. of winding cores or reels, are not covered by this standard. Technical safety requirements for the design and construction of thickness monitoring devices are not covered by this standard. Hazards due to electro-magnetic radiation, e.g. from the use of thickness monitoring devices, are not covered by this standard. Toxic or chemical hazards and hazards due to dusts, fumes or gases, which could occur from the materials being wound are not covered by this standard. NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC. This standard applies to machines which are manufactured after the date of approval of the standard by CEN.

Rubber and plastics machines - Winding machines for film or sheet - Safety requirements

EN 13418:2004 橡胶和塑料机械.薄膜和薄板的卷切机.安全要求.包含修改件A1-2008

This European Standard specifies the safety requirements for the design and construction of winding, unwinding and rewinding machines for film or sheet manufactured from rubber, plastics and composite materials in respect of the significant hazards listed in clause 4. A winding machine begins at the intake of the film or sheet into the winding machine and ends at the discharge position of the reel(s). An unwinding machine begins at the take-up position of the reel(s) and ends at the film or sheet takeoff point. A rewinding machine begins at the take-up position of the reel(s) and ends at the discharge position of the reel(s). In some machines the winding, unwinding and rewinding functions may be combined. The following functional groups are covered byThis European Standard: fixed point roll; film or sheet tension control; winding zone; reel change device; reel loading and unloading devices; and the following additional equipment integrated into the winding machine: spreader roll device; longitudinal cutting unit; slitting device; film or sheet alignment device; static eliminator. Technical safety requirements for the design and construction of aids for lifting and handling, e. g. of winding cores or reels, are not covered byThis standard. Technical safety requirements for the design and construction of thickness monitoring devices are not covered byThis standard. Hazards due to electro-magnetic radiation, e. g. from the use of thickness monitoring devices, are not covered byThis standard. Toxic or chemical hazards and hazards due to dusts, fumes or gases, which could occur from the materials being wound are not covered byThis standard. NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered byThis European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.This standard applies to machines which are manufactured after the date of approval of the standard by CEN.

Plastics and rubber machines - Winding machines for film or sheet - Safety requirements Incorporates Amendment A1: 2008

ANSI/SPI B151.15-2003 挤压吹塑模压机的建造、保养和使用

Applies to all Extrusion Blowmolding Machines that process plastic materials to form a parison that is blown into the shape of a mold held together by a clamp(s)

Extrusion Blow Molding Machines, Construction, Care, and Use of