85.060 纸和纸板 标准查询与下载

T/SDPAA 0001-2020 纸管原纸

5.1　技术指标 5.1.1　纸管原纸的技术指标应符合表1规定。 5.1.2　纸管原纸的技术指标也可按订货合同的规定。 5.2　尺寸及偏差 5.2.1　卷筒纸管原纸的幅宽为500mm～2000mm，其偏差不应超过±6 0mm。 5.2.2　卷筒纸管原纸的卷筒直径为800mm、1000mm、1100mm、1200mm，其直径偏差不应超过±50mm。 5.2.3　盘状纸管原纸的幅宽按合同规定，宽度偏差为±0.25mm。 5.2.4　可按订货合同规定生产其他尺寸的产品。 5.3　外观质量 5.3.1　纸管原纸切边应整齐、洁净。 5.3.2　纸管原纸接头处应用胶带纸粘牢，并作明显标志。每卷纸的接头数应符合以下要求： a)　A～3A级应不超过1个。 b)　B级应不超过2个。 c)　C级应不超过3个。  5.3.3　纸管原纸表面应平整，不应有折子、皱纹、破洞、裂口、砂粒、硬质块等影响使用的外观纸病。分切后产品不应有荷页边现象。 5.3.4　纸管原纸的纸芯不应有瘪芯现象。卷筒端面应平整，形成的锯齿或凹凸面不应超过5mm。 5.3.5　纸管原纸每10㎡内，直径大于5mm的浆块或湿疤个数要求： a)　A～3A级不应超过1个。 b)　B、C级不应超过2个。

Core-board

T/ZZB 1950-2020 数码热升华转印纸

本文件规定了数码热升华转印纸的术语和定义、型号、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于以热升华转印原纸为支撑体，经涂布的可用于数码、服装、鞋材、织带、服装标签等工业化印花行业的数码热升华转印纸。以下简称“数码纸”。

Digital sublimation transfer paper

T/ZZB 1921-2020 吸管原纸

本文件规定了吸管原纸的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺等要求。 本文件适用于一次性纸质吸管用纸。

Straw base paper

T/ZZB 1914-2020 非预涂胶铜版纸标签

本文件规定了非预涂胶铜版纸标签（以下简称“标签”）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存、质量承诺。 本文件适用于铜版纸经平版印刷（胶印）、覆膜、裁切等工序制成的非预涂胶标签。

Adhesive free coated paper label

UNI ISO 2493-1:2020 纸和纸板《耐弯曲性的测定》第1部分：恒定挠曲率

Paper and board — Determination of bending resistance — Part 1: Constant rate of deflection

UNI ISO 2493-2:2020 纸和纸板《耐弯曲性能的测定》第2部分：泰伯型试验机

Paper and board — Determination of resistance to bending — Part 2: Taber-type tester

T/ZZB 1864-2020 喷墨打印用聚丙烯（PP）复合纸

本文件规定了喷墨打印用聚丙烯（PP）复合纸的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、包装、标志、运输、贮存、质量承诺。 本文件适用于以聚丙烯（PP）基膜为基材，经涂布而成的喷墨打印纸。

Polypropylene (PP) composite paper for inkjet printing

LST CEN/TS 17497-2020 纸浆、纸和纸板 纸和纸板提取物中双酚 A 的测定

Pulp, paper and paperboard - Determination of bisphenol A in extracts from paper and paperboard

ONR CEN/TS 17497-2020 纸浆、纸和纸板-纸和纸板提取物中双酚A的测定（CEN/TS 17497:2020）

Pulp, paper and paperboard - Determination of bisphenol A in extracts from paper and paperboard (CEN/TS 17497:2020)

T/ZZB 1773-2020 格拉辛纸

本文件规定了格拉辛纸的基本要求、技术要求、试验方法、检验规则、标志、包装、贮存和运输及质量承诺。 本文件适用于经超级压光，可直接涂硅油，且具有一定透明度、用于不干胶标签底纸的卷筒格拉辛纸。

Glassine Paper

T/SDQE 007-2020 泰山品质 新闻纸

本文件规定了泰山品质新闻纸（以下简称“新闻纸”）的产品分类、要求、试验方法、检验规则及 标志、包装、运输和贮存。 本文件适用于高速轮转印刷、平版印刷新闻报刊用纸

Taishan quality newsprint

ASTM D5663-15(2020) 用于验证包装纸和纸板中回收内容的标准指南

1.1 This guide provides an approach for both the calculation and the substantiation of recycled content of finished packaging paper and paperboard products. A mass balance approach is recommended for use by manufacturers since no physical or chemical test method is currently available to determine absolute recycled content of a finished paper product. Calculations are based on time weighted average flows which are based on furnish component flow rates and consistency. Recommended approaches to the calculations include by batch or by time weighted average for a specific grade or similar grades. It is not recommended that average recycle content be allocated by mathematical apportionment rather than by actual fiber content. That is, if 50 % recycled fiber is used over time that is the time weighted average. One cannot use this same data to report 50 % of the production is 100 % recycled. 1.1.1 Percentage calculations are based on lb/ton or kg/ tonne with the time frame constrained by machine and grade (see 10.1.1.1 and 10.1.1.2). 1.1.2 Pulping and recycling yields are not used in these calculations. The calculations of recycled fiber content in the finished product is solely a function of type of fibers in the furnish flows, the volume of flow and the time period considered. 1.2 This guide covers (1) recycled content of packaging paper and paperboard products that contain any amount or kind of recycled fiber; and (2) methods to calculate and substantiate the level(s) of recycled fiber content claimed by an agreement between the buyer and the seller. 1.2.1 This guide may be used with or without modification to calculate or substantiate the recycled content of packaging paper and paperboard products when recovered nonfibrous materials (for example, filler) are a part of the recycled fiber furnish. Limited guidance is provided for appropriate modifications to this guide for the determination of amount of recycled nonfibrous materials in paper products. 1.3 This guide does not recommend either an amount or a kind of recycled fiber or material to use since (1) the amount and kind of recycled content in a packaging paper or paperboard product should be agreed upon between the buyer and the seller, and (2) the calculation and substantiation procedures recommended may be used for any amount or kind of recycled material agreed upon between the buyer and the seller. 1.4 The mass balance calculation method recommended by this guide may or may not comply with applicable federal, state, or local laws for recycled content statements intended to be received by consumers. Limited guidance on content statements is in Appendix X1. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 10, of this guide: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Validating Recycled Content in Packaging Paper and Paperboard

T/JJZY 001-2020 夹江国画纸

指标名称  单位  要求 紧度  g/cm 3 0.35土0.04 亮度（白度） ≥  %  70.0 抗张指数 纵横平均 ≥  N.m/g 25.0 撕裂度 纵横平均 ≥  mN  240 裂断长 纵横平均 ≥  km  1.9 湿抗张强度 纵横平均 ≥ N/m  31.0 耐老化亮度（绝对值）下降 ≤  %  5.0 吸水性 纵横平均 ㎜/60S 25-50 纵横差 ≤  4.0 伸缩性 受湿后平均伸长 ≤ % 0.75 干燥后平均收缩 ≤  1.00 尘埃度 0.5mm 2 ～2.0 mm 2 (非黑) ≤ 个/㎡ 80 0.3mm 2 ～1.5 mm 2 (黑) ≤ 28 ＞2.0 mm 2 ( 黑 ) 不应有 ＞2.0 mm 2 ( 非黑 ) 不应有 双浆团  个/㎡  不应有 交货水份 ≤ %  10.0 润墨性  应符合附录A要求

Jiajiang Chinese painting paper

T/JJZY 002-2020 夹江书画纸

指标名称  单位  指标 定量 a g/㎡ 32±2.0 35±2.0 38±2.0 40±2.0 45±2.5 50±3.0 60±3.0 70±3.5 80±3.5 90±4.0 95±4.0 100±4.5 120±5.0 150±6.0 紧度  g/cm 3 0.38±0.05 亮度（白度） b ≥ %  70.0 裂断长 纵横平均 ≥  km  1.9 撕裂度 纵横平均 ≥  mN  150 湿抗张强度 纵横平均 ≥ mN  380 耐老化亮度（绝对值）下降 b ≤ %  5.0 吸水性 c 纵横平均 ㎜/60S 18-50 纵横差 ≤  4.0 伸缩性 受湿后平均伸长 ≤ % 0.75 干燥后平均收缩 ≤  1.00 尘埃度 0.5mm 2 ～2.0 mm 2 (非黑) ≤ 个/㎡ 80 0.3mm 2 ～1.5 mm 2 (黑) ≤ 28 ＞2.0 mm 2 ( 黑 ) 不应有 ＞2.0 mm 2 ( 非黑 ) 不应有 交货水份 ≤ %  10.0 润墨性 d 应符合附录 A 要求

Jiajiang calligraphy and painting paper

T/JJZY 003-2020 毛边纸

指标名称  单位  指标 定量 a g/㎡ 23±2.0 25±2.0 28±2.0 32±2.0 35±2.0 38±2.0 40±2.0 45±2.5 紧度  g/cm 3 0.40±0.10 亮度（白度） b ≤ %  50.0 T/JJZY 003—2020 3 续表 2 理化指标 指标名称  单位  指标 紧度  g/cm 3 0.40±0.10 亮度（白度） b ≤ %  50.0 裂断长 纵横平均 ≥  km  1.6 撕裂度 纵横平均 ≥  mN  140 湿抗张强度 纵横平均 ≥ N/m  21.0 耐老化亮度（绝对值）下降 b ≤ %  5.0 吸水性 纵横平均 ㎜/60S 18-50 纵横差 ≤  5.0 伸缩性 受湿后平均伸长 ≤ % 0.75 干燥后平均收缩 ≤  1.00 尘埃度 0.5mm 2 ～2.0 mm 2 (非黑) ≤ 个/㎡ 150 0.3mm 2 ～1.5 mm 2 (黑) ≤ 40 ＞2.0 mm 2 ( 黑 ) 不应有 ＞2.0 mm 2 ( 非黑 ) 不应有 铅(Pb) c ≤  mg/kg  3.0 砷(As) c ≤ mg/kg  1.0 甲醛 c ≤ 交货水份 ≤ %  10.0 润墨性 d 应符合附录 A 要求

Raw paper

KS M ISO 1974-2020 纸 - 抗撕裂性的测定 - 埃尔门多夫法

Paper — Determination of tearing resistance — Elmendorf method

KS M ISO 12625-11-2020 组织纸和组织产品 - 第11部分:湿球爆裂强度的测定

Tissue paper and tissue products —Part 11: Determination of wet ball burst strength

KS M 7076-2020 瓦楞夹心原纸纸

Corrugating medium paper

KS M ISO 16532-1-2020 纸和纸板 - 耐油脂测定 - 第1部分:渗透性试验

Paper and board — Determination of grease resistance —Part 1: Permeability test

KS M ISO 22891:2020 纸 - 测定透光率的漫反射的测宽

Paper — Determination of transmittance by Paper — Determination of transmittance by