85.060 纸和纸板 标准查询与下载

ISO 536:2019 纸和纸板 - 重量的测定

This document specifies a method for determining the grammage of paper and board.

Paper and board — Determination of grammage

KS M ISO 2471-2019 纸和纸板 - 不透明度（纸背衬）的测定 - 漫反射法

Paper and board－Determination of opacity(paper backing)－Diffuse reflectance method

KS M ISO 287-2019 纸和纸板 - 大量烘干法测定水分含量

Paper and board — Determination of moisture content of a lot — Oven-drying method

KS M ISO 287:2019 纸和纸板 - 大量烘干法测定水分含量

Paper and board — Determination of moisture content of a lot — Oven-drying method

KS M ISO 2471:2019 纸和纸板 - 不透明度（纸背衬）的测定 - 漫反射法

Paper and board－Determination of opacity(paper backing)－Diffuse reflectance method

QB/T 5400-2019 薄型封装纸

Thin packaging paper

T/ZZB 1258-2019 非热封型茶叶滤纸

本标准规定了非封型茶叶滤纸的基本要求、技术要求、试验方法、检验规则和标志、包装、运输、贮存及质量承诺。 本标准适用于非热封型茶叶滤纸。

Tea bag paper of non heat seal type

T/ZZB 1165-2019 编织原纸

本标准规定了编织原纸的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于生产纸带、纸绳、编织帽和工艺礼品，或作装饰用的纸。

Braided base paper

T/ZZB 1156-2019 热封型茶叶滤纸

本标准规定了热封型茶叶滤纸的基本要求、生产制造、 检验规则、技术要求、 试验方法、和标志、包装、运输、贮存及质量承诺。 本标准适用于热封型茶叶滤纸。

Heat sealable filter paper for teabags

BS ISO 2144:2019 纸、纸板、纸浆和纤维素纳米材料 900°C 灼烧残渣（灰分含量）的测定

What is ISO 2144 on Determining ash content about?   ISO 2144 is an international multi-series standard that covers guidelines for paper, board, pulps, and cellulose nanomaterials.    ISO 2144 describes the determination of the residue (ash content) on the ignition of paper, board, pulps, and cellulose nanomaterials. It is applicable to all types of paper, board, pulp, and cellulose nanomaterial.    ISO 2144 provides measurement procedures to obtain a measurement precision of 0.01 % or better for residue (ash content) on ignition at 900°C.   ISO 2144

Paper, board, pulps and cellulose nanomaterials. Determination of residue (ash content) on ignition at 900 °C

BS EN 17085:2019 纸和纸板 回收纸和纸板的抽样程序

What is BS EN 17085 - Sampling paper and board for recycling   about?   BS EN 17085  is an international standard that gives guidelines for paper, pulp, and board production.    BS EN 17085  specifies a method of obtaining representative samples from a lot of paper and board for recycling for testing to determine whether or not its composition and quality comply with the requirements of  EN 643  and/or other specifications.   BS EN 17085  also specifies the positioning of probes, when in situ measurements are performed. It defines the sampling procedures which apply when sampling is carried out to resolve compliance issues and commercial disputes between buyer and seller relating to a lot of paper and board for recycling, at any point in the value chain, where those procedures are not defined in the contract between buyer and seller.

Paper and board. Sampling procedures for paper and board for recycling

ISO 2144:2019 纸、纸板、纸浆和纤维素纳米材料.在900℃下点火时残留物（灰分含量）的测定；C

This document describes the determination of the residue (ash content) on ignition of paper, board, pulps and cellulose nanomaterials. This document is applicable to all types of paper, board, pulp and cellulose nanomaterial. This document provides measurement procedures to obtain a measurement precision of 0,01 % or better for residue (ash content) on ignition at 900 °C. In the context of this document, the term “cellulose nanomaterial” refers specifically to cellulose nano- object (see 3.2 to 3.4). Owing to their nanoscale dimensions, these cellulose nano-objects can have intrinsic properties, behaviours or functionalities that are distinct from those associated with paper, board and pulps.

Paper, board, pulps and cellulose nanomaterials — Determination of residue (ash content) on ignition at 900 °C

BS ISO 5628:2019 纸和纸板 弯曲刚度的测定 两点法、三点法和四点法的一般原则

What is ISO 5628 — Bending stiffness of paper and board about?    ISO 5628 is an international standard that deals with paper and paperboard. ISO 5628 specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point, and four-point bending test methods.   ISO 5628 gives technical specifications terms, definitions, symbols, theory, different bending test methods, apparatus, sampling and preparation of test pieces, procedure, evaluation, and calculation and states the test reports for determination of bending stiffness.

Paper and board. Determination of bending stiffness. General principles for two-point, three-point and four-point methods

BS ISO 5647:2019 纸和纸板 二氧化钛含量的测定

What is ISO 5647 about?    ISO 5647 is an international standard that covers specifications for quality paper and paperboard.    ISO 5647 specifies a method for determining titanium dioxide content in all kinds of paper and board, in particular coated, or filled products. It comprises two procedures for the final determination of titanium, one of them relying on spectrophotometry and the other on flame atomic absorption spectrophotometry.     ISO 5647 gives technical specifications for terms, the principle, reagents, apparatus, selection of the sample, preparation of ash solution, reagent blank solution, spectrophotometric procedure, flame atomic absorption...

Paper and board. Determination of titanium dioxide content

ISO 5628:2019 纸和板 - 弯曲刚度的确定 - 两点 三点和四点方法的一般原则

This document specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods. For paper and paperboard in a low thickness range, the two-point bending method and the three-point bending method are suitable. For corrugated fibreboard and board with a higher thickness, the four-point bending method is recommended. The measurement conditions are defined in such a way that the test piece is not subjected to any significant permanent deformation during the test, nor is the range of validity of the formulae for calculating the bending stiffness exceeded. In these bending tests, the test pieces of paper and board are regarded as “beams” as defined by the science of the strength of materials, see Reference [2].

Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods

ISO 5647:2019 纸和纸板二氧化钛含量的测定

This document specifies a method for determining titanium dioxide content in all kinds of paper and board, in particular coated or filled products. It comprises two procedures for the final determination of titanium, one of them relying on spectrophotometry and the other on flame atomic absorption spectrophotometry. The limits of the determination depend on the amount of sample taken (8.1). NOTE The method is designed for the determination of titanium dioxide. Titanium present in other forms, for example as a constituent of clay, will not interfere in the determination.

Paper and board — Determination of titanium dioxide content

T/ZZB 1089-2019 负离子壁纸

本标准规定了负离子壁纸的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本标准适用于能够诱生空气负离子功能的纯无纺纸负离子壁纸和无纺纸基负离子壁纸。

Negative ion wallpaper

BS ISO 11093-9:2019 纸和纸板 核心测试 抗平压强度的测定

What is ISO 11093 ‑ 9 about - Flat crush resistance of paper and board products ?    ISO 11093 ‑ 9 is the ninth part of the ISO 11093 multi-series standard that focuses on testing of cores for paper and board products. This international standard helps its users to determine the durability of their paper and board products.    ISO 11093 ‑ 9 specifies a method for the determination of the maximum flat crush resistance of wound paper and board cores.   Note: If the wall thickness of the core is less than 5 mm, the breaking point is not detectable.   Who is ISO 11093 ‑ 9 - Flat crush r...

Paper and board. Testing of cores. Determination of flat crush resistance

ISO 11093-9:2019 纸和纸板.芯的试验.第9部分:平压强度的测定

This part of ISO 11093 specifies a method for the determination of the maximum flat crush resistance of wound paper and board cores. NOTE If the wall thickness of the core is less than 5 mm, the breaking point is not detectable.

Paper and board — Testing of cores — Part 9: Determination of flat crush resistance

BS EN 17163:2019 纸浆、纸张和纸板 LC-MS 法测定水提取物中的芳香伯胺 (PAA)

What is BS EN 17163 ‒ Primary aromatic amines in a water extract about?    BS EN 17163 is an international standard that deals with all the information regarding pulp, paper, and board industries.   BS EN 17163 specifies two representative methods for the determination of the extractable amount of specific primary aromatic amines (PAA) in a water extract of paper, board, and pulp samples. It uses the means of HPLC with MS/MS detection which differ concerning the choice of the mobile and stationary phases.   BS EN 17163 gives the extractable amount of a primary aromatic amine (PAA), that is expressed in mg PAA per litre water extract. This method is suitable for the determination of PAA with a working range of about 0.001 mg/l – 0.020 mg/l water extract.    Who is BS EN 17163  ‒ Primary aromatic amines in a water extract for?   BS EN 17163 on p rimary aromatic amines in a water extract is for the following 

Pulp, paper and board. Determination of primary aromatic amines (PAA) in a water extract by a LC-MS method