87.040 涂料和清漆 标准查询与下载

T/CASME 1340-2024 快干水性醇酸树脂涂料通用技术要求

本文件规定了快干水性醇酸树脂涂料通用技术要求的术语和定义、产品分类、基本要求、生产工艺、技术要求、试验方法、检验规则、标志、包装、运输和贮存等内容。

General technical requirements for fast-drying water-based alkyl resin coatings

T/CASME 1341-2024 快干醇酸漆通用技术要求

本文件规定了快干醇酸漆通用技术要求的术语和定义、生产原料、生产工艺、技术要求、试验方法、检验规则、施工要求以及标志、包装、运输和贮存。

General technical requirements for quick-drying, alcohol and acid paint

ASTM E1796-24 建筑物含铅涂料用液体涂层封装产品的选择和使用标准指南

1.1 This guide is intended to provide building users such as private building owners, contractors, architects, homeowners, and regulatory authorities with assistance in selecting an appropriate liquid coating encapsulation product for architectural residence and child-care facility use situations for abating leaded paint. This guide also provides information that can be used to assist in the following: (1) determining whether a painted surface is suitable for encapsulation, (2) applying a liquid coating encapsulation product, (3) evaluating installed liquid coating encapsulation products, and (4) maintaining the encapsulated surface. 1.2 This guide applies to any liquid-applied product that relies primarily on adhesion for attachment to the surface and is designed to reduce human exposure to lead in paint. 1.3 This guide is not intended for use as a training manual. The information contained herein is not all-inclusive and does not provide comprehensive instructions for the selection, application, or maintenance of specific liquid coating encapsulation products. This guide is intended to supplement information supplied by encapsulation product manufacturers and safety requirements established by law. The user of this guide shall refer to the encapsulation product manufacturer’s instructions for encapsulation product application and maintenance. 1.4 This guide does not cover minimum material performance requirements for liquid coating encapsulation products. Performance specifications for non-reinforced liquid coating encapsulation products are provided in Specification E1795. 1.5 Encapsulation products for use on industrial steel structures are not covered in this guide. Industrial steel structures include, but are not limited to, bridges, water towers, and tanks. 1.6 Limited documentation is available on evaluating the field performance of liquid coating encapsulation products. A conservative approach to assessing the selection and use of liquid coating encapsulation products is thus adopted in this guide. As appropriate, the guidance provided within will be revised as additional knowledge regarding how these products perform over time is gained. 1.7 The user of this guide should follow all regulations promulgated by authorities having jurisdiction regarding the use of encapsulation products. 1.8 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings

BS EN ISO 20567-4:2024 油漆和清漆 涂层抗石击性的测定 小测试区域的移动多次冲击测试

Paints and varnishes. Determination of stone-chip resistance of coatings - Mobile multi-impact testing on a small testing area

T/CSTM 00975.1-2024 船舶防污漆中禁用防污剂含量的测定 第1部分：高效液相色谱法

本文件规定了采用高效液相色谱法测定船舶防污漆中禁用防污剂含量的原理、试剂和材料、仪器和设备、取样、试验步骤、精密度、试验报告等内容。 本文件适用于涂料、涂料用原材料及涂膜中西布曲尼（Cybutryne）含量和滴滴涕含量的测定，不适用有机锡类防污剂含量的测定。

Determination of forbidden antifouling agent content in marine antifouling coatings - Part 1: High performance liquid chromatography method

T/CSTM 00972-2024 原厂车辆涂料 单位涂装面积的挥发性有机化合物释放量的测定

本文件规定了采用涂布率法测定单位涂装面积的挥发性有机化合物释放量的原理、取样、测试步骤、计算、精密度、试验报告等内容。 本文件适用于车辆制造业中采用原厂车辆涂料进行工业涂装时VOC释放量的测定。其他采用OEM涂料进行工业涂装的制造行业也可参照执行。

Ｖehicle coatings of original equipment manufacturer —Determination of volatile organic compound emissions per unit coating area

T/HBBWA 25-2024 外墙防水装饰一体化涂料(高耐候)

本文件规定了外墙防水装饰一体化涂料（高耐候）（简称防水装饰一体化涂料）的标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以聚合物、水泥、细骨料为基料，掺入颜料和添加剂配制而成的，采用刷涂、滚涂或喷涂施工方法，在建筑物外墙起到防水和装饰保护的双重作用的涂料。 本标准于2023年9月首次发布，2024年2月第一次修订。

Integrated coating for exterior wall waterproofing and decoration (high weather resistance)

T/CSTM 00971-2024 电气绝缘用热固性粉末涂料

本文件规定了电气绝缘用热固性粉末涂料的分类、要求、试验方法、检验规则以及标志、包装、运输及贮存等内容。 本文件适用于以合成树脂、固化剂为主要成膜物质，并加入颜料、填料、助剂等物质，制得的具有电气绝缘性能的热固性粉末涂料。

Thermosetting powder coatings for electrical insulation

T/CSTM 00973-2024 涂料中有害芳香胺含量的测定

本文件规定了采用气相色谱-质谱联用法测定涂料中有害芳香胺含量的原理、试剂和材料、仪器和设备、取样、试验步骤、精密度、试验报告等内容。 本文件适用于涂料及相关材料中有害芳香胺含量的测定，包括但不限于附录A中表A.1列举的有毒芳香胺。其他领域用聚合物材料及原材料中芳香胺含量的测定也可参考本文件。

Determination of harmful aromatic amines content in coatings

ASTM D4213-24 用磨损重量损失法测定涂料耐擦洗性的标准试验方法

1.1 This test method covers an accelerated procedure for determining the resistance of paints to erosion caused by scrubbing. (Note: The term wet abrasion is sometimes used for scrubbing, and wet abrasion resistance or scrubbability for scrub resistance.) Although scrub resistance tests are intended primarily for interior coatings, they are sometimes used with exterior coatings as an additional measure of film performance. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss

ASTM D2369-24 涂层挥发性含量的标准试验方法

1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 °C 6 5 °C for 60 min. NOTE 1—The coatings used in these round-robin studies represented air-dried, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems. 1.2 Sixty minutes at 110 °C 6 5 °C is a general purpose test method based on the precision obtained with both solventborne and waterborne coatings (see Section 9). 1.3 This test method is viable for coatings wherein one or more parts may, at ambient conditions, contain liquid coreactants that are volatile until a chemical reaction has occurred with another component of the multi-package system. NOTE 2—Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and allow the specimens to stand at room temperature for 1 h prior to placing them into the oven. 1.4 Test Method D5095 for Determination of the Nonvolatile Content in Silanes, Siloxanes and Silane-Siloxane Blends Used in Masonry Water Repellent Treatments is the standard method for nonvolatile content of these types of materials. 1.5 Test Methods D5403 for Volatile Content of Radiation Curable Materials is the standard method for determining nonvolatile content of radiation curable coatings, inks and adhesives. 1.6 Test Method D6419 for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks is the method of choice for these types of printing inks. 1.7 This test method may not be applicable to all types of coatings. Other procedures may be substituted with mutual agreement between the producer and the user. NOTE 3—If unusual decomposition or degradation of the specimen occurs during heating, the actual time and temperature used to cure the coating in practice may be substituted for the time and temperature specified in this test method, subject to mutual agreement between the producer and the user. The U.S. EPA Reference Method 24 specifies 110 °C 6 5 °C for 1 h for coatings. NOTE 4—Practice D3960 for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings describes procedures and calculations and provides guidance on selecting test methods to determine VOC content of solventborne and waterborne coatings. 1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Volatile Content of Coatings

ASTM D2064-24 建筑涂料耐印刷性的标准试验方法

Standard Test Method for Print Resistance of Architectural Paints

ASTM D3023-98(2024) 测定木制品上工厂涂覆的涂层对污渍和试剂的耐受性的标准实施规程

Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents

ASTM D7488-11(2024) 乳胶漆开启时间的标准试验方法

Standard Test Method for Open Time of Latex Paints

ASTM D6441-05(2024) 测量粉末涂层遮盖力的标准试验方法

Standard Test Methods for Measuring the Hiding Power of Powder Coatings

ASTM D8090-24 用动态成像法测定涂料和颜料粒度分布的标准试验方法

1.1 This test method covers the determination of particle size distribution of liquid paints and pigmented liquid coatings by Dynamic Image Analysis. This method includes the reporting of particles ≥1 µm in size and up to 300 µm in size. NOTE 1—Shape is used to classify particles, droplets and bubbles and is not a reporting requirement. NOTE 2—The term paint(s) as used in this document includes liquid paint and liquid pigmented coatings. 1.1.1 Some paints may be too viscous to flow through the imaging instrument without dilution which may be used to help the paint flow as long as significant contamination is not introduced into the paint. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Particle Size Distribution of Paints and Pigments Using Dynamic Imaging Methods

ASTM D2091-96(2024) 油漆耐印刷性的标准试验方法

Standard Test Method for Print Resistance of Lacquers

ASTM D2794-93(2024) 有机涂层耐快速变形（冲击）影响的标准试验方法

1.1  This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation. 1.2  This test method should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the method. Interlaboratory agreement is improved when ranking is used in place of numerical values. 1.3  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

T/FPCIA 001-2023 仿石涂料应用技术规程

本文件规定了建筑内外墙用仿石涂料术语、材料、设计及基层要求、施工、质量验收等。 本文件适用于新建、扩建及改建的建筑内外墙用仿石涂料及配套材料选用、设计、施工及质量验收。

Technical specification for application of stone-like coatings

T/QGCML 2434-2023 弹性抗裂饰面涂层

本文件规定了弹性抗裂饰面涂层的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于涂抹在耐沾污性和耐候性要求较高的墙面上的弹性抗裂饰面涂层。

Elastomeric anti-cracking finish coating