87.040 涂料和清漆 标准查询与下载

T/SHHJ 000016-2023 合成树脂乳液砂壁状建筑涂料

本文件规定了合成树脂乳液砂壁状建筑涂料的术语和定义、产品分类和分等、要求、试验方法、检验规则及标志、包装和贮存。 本文件适用于在建筑物表面起装饰和保护作用，以合成树脂乳液为主要粘结剂的砂壁状建筑涂料。

Sand textured building coating based on synthetic resin emulsion

T/SHHJ 000009-2023 全装修房用合成树脂乳液内墙涂料

本文件规定了全装修房用合成树脂乳液内墙涂料的术语和定义、产品分类、分等、要求、试验方法、检验规则与标志、包装和贮存。 本文件适用于以合成树脂乳液为基料、与颜填料及各种助剂配制而成的，直接在现场涂装，对以水泥基和其他非金属材料（木质材料除外）为基材的建筑物内表面进行装饰和保护的各类建筑用墙面涂料。该产品主要用于全装修房（工程）内墙墙面。

Synthetic resin emulsion interior wall paint for fully decorated rooms

T/SHHJ 000017-2023 水性多彩建筑涂料

本文件规定了水性多彩建筑涂料产品的分类要求、试验方法、检验规则、标志、包装和贮存等内容。 本文件适用于将水性着色胶体颗粒分散于以水性成膜物质（合成树脂乳液等）、颜填料、水、助剂等构成的体系中制成的水包水型多彩涂料，该涂料通过喷涂等施涂工艺可获得仿花岗岩、大理石、壁纸等外观装饰效果，与底漆、中涂、罩光清漆（也可不用）等形成配套体系，主要用于建筑外表面的装饰和保护。

Waterborne multicolor architectural coatings

T/SHHJ 000015-2023 弹性建筑涂料

本文件规定了弹性建筑涂料的术语和定义、产品分类、要求、试验方法、检验规则及标志、包装、贮存和验收。 本文件适用于由合成树脂乳液为基料，并由各种颜料、填料和助剂等配制而成的弹性建筑涂料。

Elastomeric wall coatings

T/SHHJ 000006-2023 真石漆反射隔热涂料

本文件规定了真石漆反射隔热涂料产品的术语和定义、分类、要求、试验方法、检验规则、标志、包装和贮存等内容。 本文件适用于由合成树脂乳液、颜填料、助剂、功能材料等制成的具有隔热作用的真石漆。

Real stone paint reflective heat insulation coating

T/SHHJ 000004-2023 水性多彩反射隔热涂料

本文件规定了水性多彩反射隔热涂料产品的术语和定义、分类、要求、试验方法、检验规则、标志、包装和贮存等内容。 将水性着色胶体颗粒分散于以水性成膜物质（合成树脂乳液等）、颜填料、水、助剂、功能材料等构成的体系中制成的水包水型多彩涂料，该涂料通过喷涂等施涂工艺可获得仿花岗岩、大理石、壁纸等外观装饰效果，与底涂、中涂、面涂（也可不用）等形成配套体系，具有较高太阳光反射比、近红外反射比及半球发射率，可以达到明显隔热效果，主要用于建筑外表面的装饰和保护。

Water-based colorful reflective thermal insulation coating

T/QGCML 942-2023 无机基质磷酸盐颜料制备技术规范

本标准规定了无机基质磷酸盐颜料制备技术规范的术语定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于无机基质磷酸盐颜料的制备。

Technical specifications for the preparation of inorganic matrix phosphate pigments

T/SCDA 053-2023 EPIC1建筑用复合气凝胶隔热涂料系统应用技术标准

附加热阻（m2·K/W） ≥0.30   JG/T 517

EPIC1 technical standards for the application of composite airgel thermal insulation coating systems for buildings

ISO 4624:2023 油漆和清漆 附着力拉拔试验

This document specifies three methods for determining the adhesion by carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product. These methods include: — method A: using two dollies, suitable for testing both rigid and deformable substrates; — method B: testing from one side only, using a single dolly, suitable for rigid substrates only; — method C: using dollies, one as a painted substrate. These test methods have been found useful in comparing the adhesion behaviour of different coatings. It is most useful in providing relative ratings for a series of coated panels exhibiting significant differences in adhesion. The test can be applied using a wide range of substrates. Different procedures are given according to whether the substrate is deformable, e.g. thin metal, plastics and wood, or rigid, e.g. thick concrete and metal plates. To avoid distortion of the substrate during the tensile test, it is common to use a sandwich construction. For example, for special purposes, the coating can be applied directly to the face of a test dolly.

Paints and varnishes. Pull-off test for adhesion

T/CNCIA 01031-2023 水泥基艺术涂料

本文件规定了水泥基艺术涂料的分类、要求、试验方法、检验规则以及标识、包装、运输和贮存。 本文件适用于室内外墙面、地面及室内墙顶装饰用水泥基艺术涂料产品。

Cement-based art coatings

T/ZCIA 12203-2023 船壳涂料

本文件规定了船壳涂料的技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本文件适用于涂敷在船舶满载水线以上的建筑物外部（含桅杆和起重机械）所用的涂料。

Topside paint

ASTM D4587-23 涂料和相关涂层的荧光紫外线冷凝暴露的标准实施规程

1.1 This practice describes artificial accelerated weathering methods for testing the durability of coatings and related products using fluorescent UV lamps and water apparatus operated in accordance with Practices G151 and G154. 1.2 This practice also makes recommendations for preparation of test specimens, exposure duration, and the evaluation of test results. NOTE 1—ISO 16474-3 also describes fluorescent UV lamp and water apparatus for artificial accelerated weathering of paints and coatings. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings

ASTM D4039-09(2023) 高光泽表面反射雾度的标准测试方法

Standard Test Method for Reflection Haze of High-Gloss Surfaces

ASTM D3891-23 涂料、清漆、清漆和相关产品试验用玻璃板的制备标准实施规程

1.1 This practice covers the preparation of glass panels for subsequent testing of paint, varnish, lacquer, and related products.2 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products

ASTM D5682-18(2023) 液体涂料及相关材料电阻率的标准测试方法

Standard Test Methods for Electrical Resistivity of Liquid Paint and Related Materials

ASTM D1200-23 通过福特粘度杯进行粘度的标准测试方法

1.1 This test method covers the determination of the viscosity of Newtonian or near-Newtonian paints, varnishes, lacquers, and related liquid materials with the Ford-type efflux viscosity cup. If the material is non-Newtonian, that is, shear-thinning or thixotropic, Test Method D2196 should be used. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Viscosity by Ford Viscosity Cup

KS V 8891-2023 用转鼓法测定防污涂料表面摩擦的实验室试验方法

Laboratory test method for skin friction of antifouling paints by rotating drum

ASTM D711-23 路面标记无拾取时间的标准测试方法

1.1 This test method covers a laboratory procedure for determining the no-pick-up time of pavement markings. The method uses a wheel consisting of a metal cylinder with rubber O-rings. The wheel is rolled down a ramp over a freshly applied pavement marking film repeatedly until there is no transfer of the marking material to the rubber rings. The elapsed time from pavement marking film application to point of no marking material transfer is the no-pick-up time. Key variables to be controlled during testing are wet film thickness, temperature, humidity, air flow, and use of retroreflective optics. This standard provides three options for the testing of the no-pick-up time for pavement markings. The first option, Method A, specifies controls for temperature, humidity, and air flow during testing; a second option, Method B, specifies controls for temperature and humidity during testing, and a third option, Method C, provides guidance for performing this with a drop on application of retroreflective optics such as glass beads, Waterborne and Solvent Borne pavement markings are typically tested using Procedure A or Procedure B, without the application of drop on retroreflective optics. Pavement markings that are two component 100 % solids are typically tested using Method C. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for No-Pick-Up Time of Pavement Markings

ISO/CD 2884-1:2023 色漆和清漆 使用旋转粘度计测定粘度 第 1 部分：高剪切速率下操作的锥板粘度计

Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear

ISO/CD 16053-2:2023 色漆和清漆 室外木材涂料和涂料系统 第 2 部分：自然风化试验

Paints and varnishes — Coating materials and coating systems for exterior wood — Part 2: Natural weathering test