87.040 涂料和清漆 标准查询与下载

GSO ISO 1524:2023 油漆、清漆和印刷油墨 研磨细度的测定

This document specifies a method for determining the fineness of grind of paints, inks and related products by use of a suitable gauge, graduated in micrometres. It is applicable to all types of liquid paints and related products, except products containing pigments in flake form (e.g. glass flakes, micaceous iron oxides, zinc flakes).

Paints, varnishes and printing inks — Determination of fineness of grind

GSO ISO 2409:2023 油漆和清漆 划格测试

This document specifies a test method for assessing the resistance of paint coatings and varnishes (including wood stains) to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate. The property determined by this empirical test procedure depends, among other factors, on the adhesion of the coating to either the preceding coat or the substrate. This procedure is not, however, a means of measuring adhesion. NOTE 1 Where a measurement of adhesion is required, see the method described in ISO 4624. NOTE 2 Although the test is primarily intended for use in the laboratory, the test is also suitable for field testing. The method described can be used either as a pass/fail test or, where circumstances are appropriate, as a six-step classification test. When applied to a multi-coat system, assessment of the resistance to separation of individual layers of the coating from each other can be made. The test can be carried out on finished objects and/or on specially prepared test specimens. Although the method is applicable to paint on hard (e.g. metal) and soft (e.g. wood and plaster) substrates, these different substrates need a different test procedure (see Clause 8). The method is not suitable for coatings of total thickness greater than 250 µm or for textured coatings. NOTE 3 The method, when applied to coatings designed to give a rough patterned surface, will give results which will show too much variation (see also ISO 16276-2).

Paints and varnishes — Cross-cut test

GSO 2714:2023 油漆和清漆 溶剂型聚氨酯底漆二道漆

This standard covers two components solvent based polyurethane primer/ surfacer where aliphatic or aromatic isocyanate is used as a curing agent for wood and steel.

Paints and varnishes - Solvent Based Polyurethane Primer Surfacer

GSO 2710:2023 油漆和清漆 溶剂型聚氨酯透明漆

  Scope is not provided for this standard

Paints and Varnishes – Solvent Based Polyurethane Clear

GSO ISO 9038:2023 液体持续燃烧性的测定

This document specifies a procedure, at temperatures up to 100 °C, to determine whether a liquid product, that would be classified as “flammable” by virtue of its flash point, sustains combustion at the temperature(s) specified e.g. in regulations. NOTE       Many national and international regulations classify liquids as presenting a flammable hazard based on their flash point, as determined by a recognized method. Some of these regulations allow a derogation if the substance cannot “sustain combustion” at some specified temperature(s). The procedure is applicable to paints (including water-borne paints), varnishes, paint binders, solvents, petroleum or related products and adhesives, that have a flash point. It is not applicable to painted surfaces in respect of assessing their potential fire hazards. This test method is applicable, in addition to test methods for flash point, for assessing the fire hazard of a product.

Determination of sustained combustibility of liquids

T/CNCIA 02015-2023 室内墙面无机涂料施工及验收规范

本文件规定了室内墙面无机涂料施工及验收的设计、一般要求、材料及工具要求、基层处理、施工准备、施工要求、撤除保护以及验收。 本文件适用于室内混凝土基层、砂浆基层、人造纤维板基层、石膏板基层等墙体及屋顶表面无机涂料的涂装施工及验收。

Specification for construction and acceptance of interior wall inorganic coatings

T/CNCIA 01030-2023 负离子涂料

本文件规定了负离子涂料的技术要求、试验方法、检验规则以及包装、标识和贮存。 本文件适用于具有诱生空气负离子功能的建筑内墙涂料。

Negative air ions coatings

T/QGCML 771-2023 墙体腻子粉通用规范

本标准规定了墙体腻子粉通用规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于墙体腻子粉的生产及检验。

General specification for wall putty powder

T/CIET 068-2023 涂料行业绿色企业评价规范

本文件规定了涂料行业绿色企业评价的目的及范围、评价原则及要求、评价指标体系及要求、评价程序、评价报告。 本文件适用于涂料行业绿色企业管理的评价和改进，可用于企业自我评价，第二方（相关方）或第三方组织评价。

Evaluation Standards for Green Enterprises in Coatings Industry

T/FSAS 71-2023 喷粉铝合金建筑型材耐老化性能试验方法 组合荧光紫外灯法

文件规定了喷粉铝合金建筑型材耐老化性能快速检测的方法-组合荧光紫外灯法的方法概述、仪器和耗材、试板、操作步骤、试板检查、结果应用、精密度、试验报告等内容

Powder-sprayed aluminum alloy building profile anti-aging performance test method combined fluorescent ultraviolet lamp method

ASTM D3912-10(2023) 核电厂用涂层和衬里耐化学性的标准试验方法

1.1 This test method establishes procedures for the evaluation of the chemical resistance of coatings and linings for use in Coating Service Level I and II applications in nuclear power plants. 1.2 This test method is intended to be used as a screening test to evaluate coatings and linings on steel and concrete substrates. 1.3 This test method addresses two exposure intervals: (1) Short Term (Typically 5 days): Such exposures are primarily applicable for coatings exposed to chemical splash or spill. (2) Long Term (Typically 180 days): Such exposures are primarily applicable for linings exposed to continuous or near-continuous chemical immersion. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants

ASTM D4082-10(2023) γ辐射对核电厂用涂层影响的标准试验方法

1.1 This test method covers a standard procedure for evaluating the lifetime radiation tolerance of coatings to be used in nuclear power plants. This test method is applicable to Coating Service Levels I, II, and III. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants

T/CNCIA 01029-2023 水性聚偏二氯乙烯（PVDC）防腐涂料

本文件规定了水性聚偏二氯乙烯（PVDC）防腐涂料的分类和分级、要求、试验方法、检验规则以及标识、包装、贮存和运输。 本文件适用于以水为主要分散介质，以聚偏二氯乙烯树脂为主要成膜物质的单组分涂料，主要用于在大气腐蚀性等级（C2～C4，GB/T 30790.2—2014）下使用的钢结构、混凝土结构表面的装饰和保护。

Waterborne polyvinylidene chloride（PVDC）anticorrosive coatings

BS ISO 20567-4:2023 油漆和清漆 涂层抗石击性的测定 小测试区域的移动多次冲击测试

1   Scope This document specifies a mobile method for evaluating the resistance of automotive finishes to chilled-iron grit projected onto the surface under test to simulate the effect of stone chipping. Results from the test specified in this document are not comparable with results specified in ISO 20567‑1.

Paints and varnishes. Determination of stone-chip resistance of coatings - Mobile multi-impact testing on a small testing area

T/CPUMT 011-2023 石墨烯水性防腐涂料

石墨烯水性防腐涂料的分类、性能要求、试验方法、检验规则以及标志、包装和贮存。

Waterborne anti-corrosion coating of graphene

23/30458735 DC BS EN ISO 4628-6 油漆和清漆 缺陷数量和大小以及外观均匀变化强度的评价第6部分：用胶带法评价粉化程度

BS EN ISO 4628-6. Paints and varnishes. Evaluation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 6. Assessment of degree of chalking by tape method

ISO 20567-4:2023 色漆和清漆.涂层耐石屑性的测定.第4部分：小试验区域的移动多冲击试验

This document specifies a mobile method for evaluating the resistance of automotive finishes to chilled- iron grit projected onto the surface under test to simulate the effect of stone chipping. Results from the test specified in this document are not comparable with results specified in

Paints and varnishes — Determination of stone-chip resistance of coatings — Part 4: Mobile multi-impact testing on a small testing area

T/HEBQS 016-2023 水乳型沥青防水涂料

表1 水乳型沥青防水涂料产品力学性能 序号 试验项目 指标 L H 1 固体含量， % ≥ 50 2 耐热度，℃ 80±2 110±2 无流淌、滑动、滴落 3 不透水性 0.3MPa， 120min 无渗水 4 粘结强度， MPa ≥ 0.30 5 表干时间 ≤ 8 6 实干时间 ≤ 24 7 低温柔性 a，℃ 标准条件 -15 0 碱处理 -10 5 酸处理 -10 5 紫外线处理 -10 5 8 断裂伸长率， % 标准条件 450 碱处理 450 酸处理 450 紫外线处理 450 a 供需双方可以商定温度更低的低温柔度指标。

Water emulsion asphalt waterproof coating

T/HEBQS 015-2023 湿铺防水卷材

表1 3.0mm 规格的 PY 类产品单位面积质量、厚度 项 B 指 标 单位面积质量/(kg/m2) ≥ 3.1 2 厚度/mm 平均值 ≥ 2 3.0 最小单值 ≥ 2 2.7

Wet lay waterproof membrane

T/HEBQS 012-2023 金属屋面丙烯酸高弹防水涂料

金属屋面丙烯酸高弹防水涂料物理性 序号 项目 术指标 普通型 热反射型 1 固体含量/% ≥65 2 无处理拉伸强度/MPa ≥1.5 3 无处理断裂伸长率/% ≥150 4 撕裂强度/(N/mm) ≥12 5 吸水率/% ≤15 6 不透水性 0. 3 MPa,30 min 不透水 7 耐热性 90 ℃,5 h 无起泡、剥落、裂纹 8 低温弯折 -30 °C,1 h 无裂纹，并不与底材脱离 9 剥离粘结性/(N/mm) ≥30T/HEBQS 012—2023 3 序号 项 目 技术指标 普通型 热反射型 10 加热处理 拉伸强度保持率/% ≥80 断裂伸长率/% ≥100 11 浸水处理 拉伸强度保持率/% ≥80 断裂伸长率/% ≥100 12 酸处理 拉伸强度保持率/% ≥80 断裂伸长率/% ≥100 13 人工气候老化处理 拉伸强度保持率/% ≥80 断裂伸长率/% ≥100 14 加热伸缩率 伸长/% ≤1.0 缩短/% ≤1.0 15 耐沾污性（白色和浅色 a） /% 一 ≤20 16 太阳光反射比（白色） — ≥0. 80 17 半球发射率 — ≥0.80 18 有害物质含 量 挥发性有机物(VOC)， g/L ≤10 可溶性重金 属 铅 Pb， mg/kg ≤10 镉 Cd， mg/kg ≤10 铬 Cr， mg/kg ≤20 汞 Hg， mg/kg mg/kg mg/kg ≤10 注：仅对白色涂料的太阳反射比提出要求，浅色涂料太阳反射比由供需双方商定。 a 浅色是指以白色涂料为主要成分,添加适量色浆后配制成的浅色涂料形成的涂膜干燥后所呈现的浅颜色，按 GB/T 15608-2006 规定明度值为 6~9（三刺激值中的 YD65>31. 26） .

Metal roof acrylic high elastic waterproof coating