87.040 涂料和清漆 标准查询与下载

T/HEBQS 013-2023 聚氨酯防水涂料

表1 基本性能 序号 试验项目 指标 Ⅰ Ⅱ Ⅲ 1 拉伸强度， MPa ≥ 2.00 6.00 12.00 2 撕裂强度， N/mm ≥ 15 30 40 3 断裂延伸率， % ≥ 500 450 250 4 低温弯折性 -35℃，无裂纹 5 粘结强度， Mpa ≥ 1.0 6 吸水率， % ≤ 5.0 7 不透水性，（0.3MPa， 120min） 不透水 8 流平性 a 20min 时，无明显齿痕 9 定伸时老 化 热处理 无裂纹及变形 人工气候老化 a 无裂纹及变形 10 固体含量， % ≥ 单组分 90 多组分 95 11 干燥时间， h 表干时间 ≤ 12 实干时间 ≤ 24 12 热处理（80℃， 168h） 拉伸强度保持率， % ≥ 80～150 断裂延伸率， %≥ 450 400 200 低温弯折性 -30℃，无裂纹 13 碱处理（0.1%NaOH+ 饱和 Ca（OH） 2溶 液， 168h） 拉伸强度保持率， % ≥ 80～150 断裂延伸率， %≥ 450 400 200 低温弯折性 -30℃，无裂纹T/HEBQS 013—2023 3 表 1 基本性能(续) 序号 试验项目 指标 Ⅰ Ⅱ Ⅲ 14 酸处理（2%H2SO4溶 液， 168h） 拉伸强度保持率， % ≥ 80～150 断裂延伸率， %≥ 450 400 200 低温弯折性 -30℃，无裂纹 15 人 工 气 候 老 化 （1000h） a 拉伸强度保持率， % ≥ 80～150 断裂延伸率， %≥ 450 400 200 低温弯折性 -30℃，无裂纹 16 燃烧性能 a B2-E（点火 15s，燃烧 20s， Fs≤150mm， 无燃烧滴落物引燃滤纸） 17 加热伸缩量， % -4.0～+1.0 a仅用于外露使用产品。

Polyurethane waterproof coating

T/HEBQS 016-2023 水乳型沥青防水涂料

表1 水乳型沥青防水涂料产品力学性能 序号 试验项目 指标 L H 1 固体含量， % ≥ 50 2 耐热度，℃ 80±2 110±2 无流淌、滑动、滴落 3 不透水性 0.3MPa， 120min 无渗水 4 粘结强度， MPa ≥ 0.30 5 表干时间 ≤ 8 6 实干时间 ≤ 24 7 低温柔性 a，℃ 标准条件 -15 0 碱处理 -10 5 酸处理 -10 5 紫外线处理 -10 5 8 断裂伸长率， % 标准条件 450 碱处理 450 酸处理 450 紫外线处理 450 a 供需双方可以商定温度更低的低温柔度指标。

Water emulsion asphalt waterproof coating

T/HEBQS 015-2023 湿铺防水卷材

表1 3.0mm 规格的 PY 类产品单位面积质量、厚度 项 B 指 标 单位面积质量/(kg/m2) ≥ 3.1 2 厚度/mm 平均值 ≥ 2 3.0 最小单值 ≥ 2 2.7

Wet lay waterproof membrane

23/30463872 DC BS EN ISO 2811-3 油漆和清漆 密度的测定 第 3 部分：振荡法

BS EN ISO 2811-3. Paints and varnishes. Determination of density - Part 3. Oscillation method

ISO/TS 19392-5:2023 色漆和清漆.风力涡轮机转子叶片的涂层系统.第5部分：紫外线防护涂层透射特性的测量

This document specifies a test method to measure the ultraviolet (UV) and visible (VIS) spectral transmittance in the wavelength range from 280 nm to 700 nm of coatings for wind turbine rotor blades. Single and multilayer coatings or coating systems can be tested. From the spectral transmittance the transmittance of UV, VIS and the combined UV and VIS wavelength range can be calculated. It is applicable to free coatings films or coatings applied on a UV-transparent quartz substrate.

Paints and varnishes — Coating systems for wind-turbine rotor blades — Part 5: Measurement of transmittance properties of UV protective coatings

ISO/TR 5601:2023 色漆和清漆.挥发性有机化合物（VOC）和/或半挥发性有机化合物含量的测定.试验方法选择的最佳实践

This document aims to enable users to identify an appropriate method for the determination of volatile organic compounds (VOC) content and/or the semi-volatile organic compounds (SVOC) content of coating materials and their raw materials. This document provides a step-by-step procedure for identifying appropriate tests. This document is intended to be used in conjunction with ISO 11890-1, problem.

Paints and varnishes — Determination of volatile organic compound (VOC) and/or semi-volatile organic compound (SVOC) content — Best practices for the selection of test methods

T/GDTL 018-2023 建筑隔声涂料技术规范

本文件规定了建筑隔声涂料产品的术语和定义、分类、要求、试验方法、检验规则、标志、包装、贮存、施工等内容。

Technical specification for building sound insulation coating

BS EN ISO 1518-1:2023 油漆和清漆 耐划伤性的测定 恒荷载法

1   Scope This document specifies a test method for determining, under defined conditions, the resistance of a single coating or a multi-coat system of paint, varnish or related product to penetration, by scratching with a scratch stylus loaded with a specified load. The stylus penetrates to the substrate, except in the case of a multi-coat system, in which case the stylus can penetrate either to the substrate or to an intermediate coat. The method specified can be carried out: a) either as a “pass/fail” test, by testing with a single specified load applied to the stylus to assess conformity with a particular specification; or b) as an assessment test by applying increasing loads to the stylus to determine the minimum load at which the coating is penetrated. NOTE Neither this document nor ISO 1518-2 specifies a method using a curved stylus, which is specified in ISO 12137. The choice between the three methods depends on the particular practical problem.

Paints and varnishes. Determination of scratch resistance. Constant-loading method

BS EN ISO 7784-2:2023 油漆和清漆 耐磨性的测定 使用橡胶砂轮和旋转试样的方法

1   Scope This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the rotating test specimen.

Paints and varnishes. Determination of resistance to abrasion. Method with abrasive rubber wheels and rotating test specimen

BS EN ISO 22553-10:2023 油漆和清漆 电镀涂层 边缘保护

1   Scope This document specifies a test method for the evaluation of protection against corrosion of edges and stamping burrs by electro-deposition coatings. It applies to electro-deposition coatings for automotive industries and other general industrial applications, e.g. chiller units, consumer products, radiators, aerospace, agriculture.

Paints and varnishes. Electro-deposition coatings - Edge protection

BS ISO 8130-15:2023 涂料粉末 流变学

1   Scope This document specifies methods for the determination of the rheological behaviour of a coating powder both in particulate and molten form.

Coating powders - Rheology

BS EN ISO 2811-1:2023 油漆和清漆 密度的测定 比重瓶法

1   Scope This document specifies a method for determining the density of paints, varnishes and related products using a metal or Gay-Lussac pycnometer. The method is limited to materials of low or medium viscosity at the temperature of test. The Hubbard pycnometer (see ISO 3507) can be used for highly viscous materials.

Paints and varnishes. Determination of density. Pycnometer method

BS EN 16105:2023 油漆和清漆 测定间歇性与水接触的涂料中受管制危险物质释放的实验室方法

1   Scope This document specifies a laboratory method to determine the leaching behaviour of substances from coatings into water over defined time intervals. The release of substances from coatings under natural conditions cannot be determined with this method. This method can be applied to renders, when condition (4) of the Scope of CEN/TS 16637‑1 is fulfilled. (4) It is assumed that intermittent contact with water (e.g. exposure to rainwater) is tested — by convention — as permanent contact. For some coatings , (e.g. some renders with organic binders according to EN 15824) in intermittent contact to water, physical and chemical properties might be altered in permanent contact with water. These products are not covered by the Technical Specification CEN/TS 16637‑1 since the test method in CEN/TS 16637‑2 is not appropriate for these construction products.

Paints and varnishes. Laboratory method for determination of release of regulated dangerous substances from coatings in intermittent contact with water

BS EN ISO 7784-1:2023 油漆和清漆 耐磨性的测定 使用砂纸轮和旋转试样的方法

1   Scope This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive-paper covered wheels affect the coating of the rotating test specimen.

Paints and varnishes. Determination of resistance to abrasion. Method with abrasive-paper covered wheels and rotating test specimen

T/NBTL 013-2023 机械设备用水性聚氨酯涂料

本文件规定了机械设备用水性聚氨酯涂料的产品分类、要求、试验方法、检验规则、标志、包装和贮存等内容。 本文件适用于工程机械、加工机械、港口机械等金属基体表面保护和装饰用的水性聚氨酯涂料。 本文件不适用于石化通用机械设备用涂料。

Waterborne polyurethane coatings for mechanical equipment

EN ISO 7784-2:2023 色漆和清漆耐磨性的测定第2部分:用橡胶轮和旋转试验方法

This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the rotating test specimen.

Paints and varnishes - Determination of resistance to abrasion - Part 2: Method with abrasive rubber wheels and rotating test specimen (ISO 7784-2:2023)

EN ISO 7784-1:2023 色漆和清漆耐磨性的测定第1部分:用砂纸覆盖车轮旋转试验方法

This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive-paper covered wheels affect the coating of the rotating test specimen.

Paints and varnishes - Determination of resistance to abrasion - Part 1: Method with abrasive-paper covered wheels and rotating test specimen (ISO 7784-1:2023)

EN ISO 1518-1:2023 色漆和清漆.测定抗划伤性 第1部分:定负荷法

This document specifies a test method for determining, under defined conditions, the resistance of a single coating or a multi-coat system of paint, varnish or related product to penetration, by scratching with a scratch stylus loaded with a specified load. The stylus penetrates to the substrate, except in the case of a multi-coat system, in which case the stylus can penetrate either to the substrate or to an intermediate coat. The method specified can be carried out: a) either as a “pass/fail” test, by testing with a single specified load applied to the stylus to assess conformity with a particular specification; or b) as an assessment test by applying increasing loads to the stylus to determine the minimum load at which the coating is penetrated. NOTE Neither this document nor ISO 1518-2 specifies a method using a curved stylus, which is specified in ISO 12137. The choice between the three methods depends on the particular practical problem.

Paints and varnishes - Determination of scratch resistance - Part 1: Constant-loading method (ISO 1518-1:2023)

T/CI 006-2023 具有大气净化功能的沥青道路光催化涂层

平涂效果 flat coating effect 经施涂后， 涂层表面呈现平整且颜色均匀一致的装饰效果。 沥青道路光催化涂层 photocatalytic coating 以光催化为作用机理，覆盖在沥青表面的由光催化剂组成的涂层

Photocatalytic coating on asphalt road for air purification

T/CI 007-2023 沥青道路表面用光催化自清洁涂层施工技术规范

道路表面用光催化净化涂料 photocatalytic purification coating for road surface 以光催化为作用机理，改变道路的表面特性，赋予道路表面分解汽车尾气、净化大气功效的涂料，以下简称道路用光催化涂料。 光催化净尾气 photocatalytic purification of vehicle exhaust 通过光催化作用机理，分解汽车尾气中的污染物气体。 道路表面光催化涂层 photocatalytic coatings for road surfaces  将以道路用光催化涂料，采用雾化喷涂的方式均匀负载在道路表面，形成具有光催化效果的表面涂层。 道路光催化工程 road photocatalytic engineering 以道路用光催化涂料为施工用涂料，用于解决汽车尾气净化等问题的道路表面涂覆工程。 抗滑值 skid resistance 用摆式摩擦系数仪测定的表面抗滑能力，单位是英式抗滑摆值 British Pendulum（tester）Number，简称BPN。 表面色差值 surface Delta-E 表面颜色的差别大小，用?E表示 4　材料 一般规定 道路用光催化涂料进场时应提供出厂检验单和产品合格证书，材料到场后应进行性能复验，不得以供应商提供的检测报告或商检报告代替现场检测。对于施工面积超过30000m2的，每30000m2光催化涂料施工面积，需要对其使用的光催化涂料进行进场复验，复验内容包括在容器中状态、干燥时间、涂膜外观。具体步骤应符合本文件4.3中规定。 试验合格材料和未检测材料必须分开存放，试验检测不合格材料应及时清理出场。

Technical specification for construction of photocatalytic self-cleaning coatings on asphalt road surface