87.040 涂料和清漆 标准查询与下载

ISO/TS 19392-6:2023 色漆和清漆.风力涡轮机转子叶片的涂层系统.第6部分：使用离心机测定和评价结冰附着力

This document describes a method to measure ice adhesion from artificial ice on test substrates by using a centrifuge. Basic ice types are defined and test parameters for the ice removal are described to achieve reproducibility of test results for ice adhesion measurements for rotor blade coatings. This document does not intend to provide fixed test parameter to account for the diversity of relevant icing scenarios in this field of application.

Paints and varnishes — Coating systems for wind-turbine rotor blades — Part 6: Determination and evaluation of ice adhesion using centrifuge

EN ISO 2811-1:2023 涂料和清漆.密度的测定.比重瓶法

This document specifies a method for determining the density of paints, varnishes and related products using a metal or Gay-Lussac pycnometer. The method is limited to materials of low or medium viscosity at the temperature of test. The Hubbard pycnometer (see ISO 3507) can be used for highly viscous materials.

Paints and varnishes - Determination of density - Part 1: Pycnometer method (ISO 2811-1:2023)

23/30453566 DC BS EN ISO 17895 油漆和清漆 挥发性有机化合物（VOC）的测定 顶空进样气相色谱法测定 VOC

BS EN ISO 17895. Paints and varnishes. Determination of volatile organic compound (VOC). Gas-chromatographic method with headspace injection for VOC determination

ISO 4618:2023 色漆和清漆.术语和定义

This document defines terms used in the field of coating materials (paints, varnishes and raw materials for paints and varnishes). Terms relating to specific applications and properties are dealt with in standards concerning those applications and properties, including corrosion protection (see the ISO 12944 series), coating powders (see ISO 8130-14), electro-deposition coatings (see ISO 22553-1) and rheology (see ISO 3219-1). Terms on nanotechnologies are harmonized with the ISO 80004 series. Terms on pigments and extenders are harmonized with ISO 18451-1.

Paints and varnishes — Vocabulary

ISO 1518-1:2023 涂料和清漆.耐擦伤性测定.第1部分:横载荷方法

This document specifies a test method for determining, under defined conditions, the resistance of a single coating or a multi-coat system of paint, varnish or related product to penetration, by scratching with a scratch stylus loaded with a specified load. The stylus penetrates to the substrate, except in the case of a multi-coat system, in which case the stylus can penetrate either to the substrate or to an intermediate coat. The method specified can be carried out: a) either as a “pass/fail” test, by testing with a single specified load applied to the stylus to assess conformity with a particular specification; or b) as an assessment test by applying increasing loads to the stylus to determine the minimum load at which the coating is penetrated. NOTE Neither this document nor ISO 1518-2 specifies a method using a curved stylus, which is specified in

Paints and varnishes — Determination of scratch resistance — Part 1: Constant-loading method

ISO 7784-1:2023 色漆和清漆.耐磨性的测定.第1部分:旋转用砂纸包裹的转轮法

This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive-paper covered wheels affect the coating of the rotating test specimen.

Paints and varnishes — Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen

ISO 7784-2:2023 色漆和清漆 耐磨性的测定 第2部分:旋转摩擦橡胶轮法

This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the rotating test specimen.

Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen

ASTM D7395-18(2023) 500 s＜sup＞-1

ASTM D562-10(2023) 使用Stormer型粘度计测量克雷布斯单位（KU）粘度的涂料稠度的标准试验方法

1.1 This test method covers the measurement of Krebs Unit (KU) viscosity to evaluate the consistency of paints and related coatings using the Stormer-type viscometer. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer

ASTM F1428-23 紧固件用铝颗粒填充底漆/有机或无机面漆、防腐涂层的标准规范

1.1 This specification covers the basic requirements for a corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic topcoat, depending on the specific requirements. 1.2 The coating may be specified with basecoat only, or with the top coated with compatible organic polymer or inorganic topcoats, depending on the specific requirements. 1.3 The basecoat is a water-dilutable slurry containing aluminum particles dispersed in a liquid binder of chromate/ phosphate compounds. 1.4 The organic topcoats consist of polymer resins and dispersed pigments and are for service where temperatures do not exceed 230 °C (450 °F). 1.5 The inorganic topcoats consist of ceramic oxide pigments dispersed in a liquid binder of chromate/phosphate compounds and are for service where temperatures do not exceed 645 °C (1200 °F). 1.6 These coatings are applied by conventional dip/spin, dip/drain, or spray methods. 1.7 The coating process does not normally induce hydrogen embrittlement, provided that the parts to be coated have not been subjected to an acid cleaner or pretreatment (see Note 1). NOTE 1—Although this coating material contains water, it has a relatively low susceptibility to inducing hydrogen embrittlement in steel parts of tensile strengths equal to or greater than 1000 MPa (approximately RC31). Normal precautions for preparing, descaling, and cleaning steels of these tensile strengths must be observed. An initial stress relief treatment should be considered prior to any chemical treatment or cleaning operation. Acids or other treatments that evolve hydrogen should be avoided. Mechanical cleaning methods may be considered. Some steels are more susceptible to hydrogen embrittlement than others and may also require hydrogen embrittlement relief baking after cleaning but before coating. Since no process can completely guarantee freedom from embrittlement, careful consideration must be given to the entire coating process and the specific steel alloy employed. 1.8 The coating systems defined by this specification can be applied to ferrous alloy steels, aluminum, and ferritic and austenitic stainless steels. 1.9 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.10 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum Particle-Filled Basecoat/Organic or Inorganic Topcoat, Corrosion Protective Coatings for Fasteners

BS EN ISO 4628-5:2022 油漆和清漆 评估缺陷的数量和大小以及外观均匀变化的强度 剥落程度的评估

1   ​Scope This document specifies a method for assessing the degree of flaking of coatings by comparison with pictorial standards. ISO 4628‑1 specifies the system used for designating the quantity and size of defects and the intensity of changes in appearance of coatings. It also outlines the general principles of the system. This system is intended to be used, in particular, for defects caused by ageing and weathering, and for uniform changes such as colour changes, for example yellowing.

Paints and varnishes. Evaluation of quantity and size of defects, and of intensity of uniform changes inappearance. Assessment of degree of flaking

BS EN 927-14:2023 油漆和清漆 室外木材涂料和涂料系统 涂膜拉伸性能的测定

1   Scope This document specifies a method for determining the tensile properties of free coating films, specifically for exterior wood applications. Typical tensile properties of interest are the modulus of elasticity, the tensile strength and the elongation at break during stretching of a free coating film at constant test speed. The test methods specified in this document are applicable to coatings from which free films can be made.

Paints and varnishes. Coating materials and coating systems for exterior wood - Determination of tensile properties of coating films

ISO 8130-15:2023 涂料粉末.第15部分：流变学

This document specifies methods for the determination of the rheological behaviour of a coating powder both in particulate and molten form.

Coating powders — Part 15: Rheology

EN ISO 22553-10:2023 色漆和清漆.电沉积涂层.第10部分:边缘保护

This document specifies a test method for the evaluation of protection against corrosion of edges and stamping burrs by electro-deposition coatings. It applies to electro-deposition coatings for automotive industries and other general industrial applications, e.g. chiller units, consumer products, radiators, aerospace, agriculture.

Paints and varnishes - Electro-deposition coatings - Part 10: Edge protection (ISO 22553-10:2022)

ISO 2811-1:2023 色漆和清漆 密度的测定 第1部分:比重瓶法

Paints and varnishes — Determination of density — Part 1: Pycnometer method

BS ISO 22553-16:2022 油漆和清漆 电沉积涂料 颜料-粘合剂比例

1   ​Scope This document specifies a test method for determining the pigment-binder ratio. It applies to electro-deposition coatings for automotive industries and other general industrial applications, e.g. chiller units, consumer products, radiators, aerospace, agriculture.

Paints and varnishes. Electro-deposition coatings - Pigment-binder ratio

BS EN 13300:2022 油漆和清漆 用于内墙和天花板的油漆和清漆 分类

1   Scope This document specifies a general system for the classification of paints and varnishes, for interior walls and ceilings, for the decoration of new and old, coated and uncoated surfaces.

Paints and varnishes. Paints and varnishes for interior walls and ceilings. Classification

T/HBTL 002-2023 防火二氧化钛

1 范围 本标准规定了防火二氧化钛的技术要求、试验方法、检验规则、检验结果的判定以及标志、包装、 运输、贮存。 本标准适用于硫酸法工艺生产的防火二氧化钛产品。主要用于膨胀阻燃体系中提高涂料、纤维等材 质的防火及阻燃性能。 2 规范性引用文件 下列文件对于本文件的应用是必不可少的。凡是注明日期的引用文件，仅所注日期的版本适用于本 文件。凡是不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 191 包装储运图示标志 GB/T 1706 二氧化钛颜料 GB/T 3049 工业用化工产品铁含量测定的通用方法： 1,10 菲啰啉分光光度法 GB/T 6678 化工产品采样总则 GB/T 6682 分析实验室用水规格和试验方法 GB/T 8170 数值修约规则与极限数值的表示和判定 GB 14907 钢结构防火涂料 GB/T 19591 纳米二氧化钛 GB/T 23842 无机化工产品中硅含量测定通用方法：还原硅钼酸盐分光光度法 HG/T 3696.1 无机化工产品化学分析用标准溶液、制剂及制品的制备第 1 部分：标准滴定溶液的制 备 HG/T 3696.2 无机化工产品化学分析用标准溶液、制剂及制品的制备第 2 部分：杂质标准溶液的制 备 HG/T 3696.3 无机化工产品化学分析用标准溶液、制剂及制品的制备第 3 部分：制剂及制品的制备 HG/T 4202 非颜料用二氧化钛 3 术语和定义 本文件不涉及术语和定义。 4 技术要求 4.1 外观 T/HBTL 002—2022 2 白色或淡黄色粉末。 4.2 粒子形貌 单分散呈球形或近似球形。

Fireproof Titanium Dioxide

T/CAS ES130124001-2022 工业品质量分级评价规则 环氧富锌漆

1　范围 本文件规定了环氧富锌漆质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于金属防腐用环氧富锌漆质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 3186  色漆、清漆和色漆与清漆用原材料 取样 GB/T 28699  钢结构防护涂装通用技术条件 HG/T 3668  富锌底漆 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则

Rules for quality grading and evaluating of industrial products—Zinc – Rich epoxy paint

T/CASME 181-2022 高韧性高封闭性烘烤型清漆

本文件规定了高韧性高封闭性烘烤型清漆的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

High toughness and high sealing baking varnish