87.080 墨水、油墨 标准查询与下载



共找到 420 条与 墨水、油墨 相关的标准,共 28

本标准规定了白板记号笔用墨水的要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于以乙醇为溶剂的颜料型白板记号笔用墨水。

Inks for white board marker

ICS
87.080
CCS
Y50
发布
2011-05-18
实施
2011-08-01

本标准规定了微孔笔用墨水的分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于油性和水性微孔笔用墨水。

Inks for microporous nib pen

ICS
87.080
CCS
Y50
发布
2011-05-18
实施
2011-08-01

本标准规定了油性记号笔用墨水的要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于油性记号笔用墨水。

Solvent-base inks for marker

ICS
87.080
CCS
Y50
发布
2011-05-18
实施
2011-08-01

本标准规定了徽墨的术语和定义,产品分类、等级,制作工艺流程,技术要求,试验方法,检验规则以及标识、包装、运输和贮存。本标准适用于古徽州地域范围内出产,以松烟、桐油烟、漆烟和胶为主要原料,采用特定工艺制成的一种主要供传统书法、绘画使用的墨锭。工艺品及收藏徽墨可参照本标准执行。

Chinese ink

ICS
87.080
CCS
Y50
发布
2011-04-21
实施
2011-05-21

Lightfastness or weatherability for specified periods of time is pertinent for certain types of printed matter such as magazine and book covers, posters and billboards, greeting cards and packages. Since the ability of printed matter to withstand color changes is a function of the spectral-power distribution of the light source to which it is exposed, it is important that lightfastness be assessed under conditions appropriate to the end-use application. The accelerated procedures covered in these exposure methods provide means for the rapid evaluation of lightfastness or weatherability under laboratory conditions. Test results are useful for specification acceptance between producer and user and for quality control. The xenon-arc lamp with an appropriate filter system exhibits a spectral-power distribution that corresponds more closely to that of daylight than the carbon-arc. In turn, accelerated tests using xenon-arc apparatus may be expected to correlate better with exposure to natural daylight than do those using carbon-arc apparatus. To accommodate variations in light intensity among days, seasons, locations, or instruments, duration of exposure is preferably expressed as the radiant exposure in specific bandpasses rather than time. In either case, the inclusion of an appropriate control serves to minimize effects of variations in test conditions. Color changes are not a linear function of duration of exposure. The preferred method of determining lightfastness or weatherability is to expose the prints for a number of intervals and to assess the time or radiant exposure required to obtain a specified color difference. For a given printing ink, lightfastness and weatherability or both depend on the type of substrate, the film thickness of the print, and the area printed (solid versus screen). Therefore, it is important that the nature of the test and control specimens correspond to that expected under actual use conditions. Note 28212;Specifications D4302, D5067, and D5098 provide useful guides to the lightfastness of pigments in several types of artists'' paints after 1260 MJ/m2 total window glass filtered solar radiant exposure (equivalent to about 2 or 3 months'' exposure to window glass filtered solar radiation in accordance with Practice G24 at a tilt angle of 45 degrees). However, because of major differences between printing inks and artists'' colors, especially in applied film thickness, it cannot be assumed that the lightfastness categories of printed ink films containing these pigments will be comparable to those indicated in the three specifications.1.1 This standard describes procedures for the determination of the relative lightfastness and weatherability of printed matter under the following conditions, which involve exposure to natural daylight or accelerated procedures in the laboratory: 1.1.1 Method 18212;Daylight behind window glass, 1.1.2 Method 28212;Outdoor weathering, 1.1.3 Method 38212;Xenon-arc apparatus with window glass filters to simulate daylight behind window glass, 1.1.4 Method 48212;Xenon-arc apparatus with water spray ......

Standard Practice for Evaluating the Relative Lightfastness and Weatherability of Printed Matter

ICS
87.080
CCS
A17
发布
2011
实施

本标准规定了水性凹版塑料薄膜表印油墨的技术要求、试验方法、检验规则、标志、包装、运输及贮存等。 本标准适用于在凹版转轮印刷机上使用的承印物为经处理的聚乙烯、聚丙烯等塑料薄膜的水性凹版塑料薄膜表印油墨。

Water based gravure surface ink for plastic film

ICS
87.080
CCS
A17
发布
2010-11-22
实施
2011-03-01

Graphic technology.colour and transparency of printing ink sets for four.colour printing.part 2: coldset offset lithographic printing

ICS
87.080
CCS
发布
2010-11-04
实施

本标准规定了龙池砚的术语和定义、地理标志产品保护范围、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于经国家质量监督检验检疫总局根据《地理标志产品保护规定》批准保护的龙池砚。

Geographical indication product Longchi inkstone

ICS
87.080
CCS
Y50
发布
2010-05-11
实施
2010-06-10

本标准规定了纸和纸板印刷适性用标准油墨的分类、要求、试验方法、检验规则、标志、使用说明、包装、运输和贮存等。 本标准适用于油墨吸收性、印刷表面强度及印刷光泽度用的标准油墨。

Standard inks for testing printability of paper and board

ICS
87.080
CCS
A17
发布
2010-04-22
实施
2010-10-01

It is generally recognized that the best method for evaluating printing properties of ink-substrate combinations is by actual printing. this practice provides a convenient method for preparing repeatable laboratory prints at realistic conditions of printing speed, printing pressure and ink film thickness. This practice is useful for quality control, specification acceptance between producer and user, product development and research. Printed samples have found widespread applications for color matching, gloss-ink holdout and other appearance properties, permanency, abrasion, drying time and many other tests of interest to the printing ink, paper and allied industries.1.1 This practice describes the procedure for preparing laboratory prints of paste printing inks using a motor-driven printability tester. 1.2 This practice covers printability testers of four different designs, referred to as Tester A, B, C, and D. These testers feature “push-button” control of printing speed and pressure and facilitate measurement of exact ink film thickness. 1.3 This practice is intended primarily for lithographic and letterpress inks that dry by oxidation or penetration. With appropriate drying or curing equipment, it is also applicable to other systems such as heat-set or energy curable. 1.4 This practice is applicable to the preparation of single-color solid-area prints by dry offset (also know as letterset) or by letterpress on any flat surface including paper, paperboard, plastic film, textiles, and metal. 1.5 The values stated in SI units are to be regarded as the standard. The only other unit of measurement used is fpm. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Preparing Prints of Paste Printing Inks by a Motor-Driven Printability Tester

ICS
87.080
CCS
A17
发布
2010
实施

Tack of printing inks controls their high-speed transfer properties, as manifested by throughput in roll milling, picking of paper during printing, and wet trapping in multicolor printing. Although an apparent tack measurement does not completely predict the transfer performance of an ink or a vehicle, it provides a meaningful parameter for quality control, development, and research. A number of three-roller tackmeters are available that differ in design features such as roller weight, geometry, and composition of the distribution system. Instruments of different types do not give the same apparent tack readings. Instruments of the same type will only give apparent tack readings within tolerance, provided that they are maintained and calibrated properly and in the same manner.1.1 This test method covers the procedure for determining the apparent tack of printing inks using a three-roller tackmeter. 1.2 This test method is applicable to all paste-type printing inks and vehicles that are essentially nonvolatile under ordinary room conditions, provided that any elastomer covered rollers in the tackmeter are resistant to attack by the particular ink or vehicle chemistry. Different elastomers may be required for different ink or vehicle chemistries. 1.3 This test method covers three-roller tackmeters of two different geometries, referred to as Geometry A and Geometry B. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Apparent Tack of Printing Inks and Vehicles by a Three-Roller Tackmeter

ICS
87.080
CCS
A17
发布
2010
实施

Graphic technology - Laboratory preparation of test prints - Screen printing inks

ICS
87.080
CCS
A17
发布
2009-11-30
实施
2009-11-30

Graphic technology. Laboratory preparation of test prints. Screen printing inks

ICS
87.080
CCS
发布
2009-11-30
实施
2009-11-30

This part of ISO 2834 specifies a test method for preparation of test prints produced with screen printing inks. These test prints are intended primarily for optical tests, such as colorimetry, transparency and reflection density as described in ISO 2846-4. They can also be used for testing gloss, light fastness and the chemical, physical and mechanical resistance to mechanical and chemical attack regarding either printing ink or substrate, or both.

Graphic technology - Laboratory preparation of test prints - Part 3: Screen printing inks

ICS
87.080
CCS
A17
发布
2008-12
实施

Standard Guide for Testing Printing Inks and Related Materials

ICS
87.080
CCS
发布
2008-06-01
实施

This part of ISO 2834 specifies a test method for preparation of test prints produced with liquid water-based or solvent-based printing inks as used in flexography and gravure printing. These test prints are intended primarily for optical tests, such as colorimetry, transparency and reflection density as described in ISO 2846-3 and ISO 2846-5. They can also be used for testing gloss, light fastness and the chemical, physical and mechanical resistance to mechanical and chemical attack regarding either printing ink and/or substrate. Flexographic inks with higher viscosity, such as those cured by radiation are also covered. This part of ISO 2834 is not applicable to inks for ink jet printing.

Graphic technology - Laboratory preparation of test prints - Liquid printing inks

ICS
87.080
CCS
A17
发布
2008-03-31
实施
2008-03-31

Graphic technology. Laboratory preparation of test prints. Liquid printing inks

ICS
87.080
CCS
发布
2008-03-31
实施
2008-03-31

Graphic technology.colour and transparency of printing ink sets for four.colour printing.part 3: publication gravure printing

ICS
87.080
CCS
发布
2008-03-27
实施

Graphic technology.colour and transparency of printing ink sets for four.colour printing.part 1: sheet.fed and heat.set web offset lithographic printing

ICS
87.080
CCS
发布
2008-03-27
实施

Graphic technology.colour and transparency of printing ink sets for four.colour printing.part 5: flexographic printing

ICS
87.080
CCS
发布
2008-03-27
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号