87.100 涂料涂覆设备 标准查询与下载

DB44/T 2044-2017 精密涂布生产线

本标准规定了精密涂布生产线的术语和定义、型号、型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存一般原则； 本标准适用于对基材表面进行功能性涂层加工的精密涂布生产线（简称生产线），其中适用的基材包括纸张、塑料薄膜、金属箔、布等。 本标准适用于热风干燥的精密涂布生产线。

Precision coating production line

ASTM D6737-12(2017) 锥形油漆刷长丝的体积密度的标准测试方法

1.1 This test method covers a procedure for measuring the weight of filaments per unit volume. 1.2 This method is applicable only to monofilament with tapered longitudinal profiles. 1.3 The values given in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bulk Density of Tapered Paintbrush Filaments

ASTM D7233-08(2017) 用于测试水平画笔长丝断裂的标准测试方法

1.1 This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent. 1.2 This method is applicable only to monofilaments with consistent longitudinal cross sectional dimensions commonly referred to as “level” filaments. 1.3 The values derived are in percent fractured filaments. For example, 2 fractured out of 18 filaments tested = 2⁄18 or 11 %. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Testing Fracture of Level Paintbrush Filaments

ASTM D7804-12(2017) 油漆滚筒盖纤维脱落标准试验方法

1.1 This test method describes a procedure for determining the amount of releasable fibers transferred from a paint roller cover to a surface being painted. 1.2 This test method is applicable to pile fabric paint roller covers. 1.3 Because both the application and panel evaluation are subjective, this test method should be used only for comparative testing within one facility using one operator for each set of applications, as the end result assigned by different facilities may not agree. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Fiber Shedding of Paint Roller Covers

ASTM D5959-12(2017) 水平画笔长丝的体积密度的标准测试方法

1.1 This test method covers a procedure for measuring the weight of filaments per unit volume. 1.2 This test method is applicable only to monofilament with consistent longitudinal (level) profiles. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bulk Density of Level Paintbrush Filaments

ASTM D5301-92(2016) 油漆刷的物理表征标准实践

1.1 This practice covers the dimensions, terminology, materials and characteristics generally considered of importance to those within, or dealing with paint brushes, and describes methods of determining these parameters. This practice is not meant to be a definitive analytical method to deformulate brushes. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Physical Characterization of Paint Brushes

DIN EN ISO 1514:2016 色漆和清漆.试验用标准板(ISO 1514-2016).德文版本EN ISO 1514-2016

Paints and varnishes - Standard panels for testing (ISO 1514:2016); German version EN ISO 1514:2016

NF C23-550-2*NF EN 50050-2:2014 手持式静电喷涂设备. 安全要求. 第2部分: 手持式可燃性的粉末涂料喷涂设备

La présente Norme Européenne spécifie les exigences relatives aux matériels portatifs de projection électrostatique ou aux matériels actionnés manuellement pour poudres de revêtement inflammables dans une plage de températures de 5 oC à 40 oC utilisées en atmosphères explosives, celles-ci étant générées par leur propre nuage de projection.La présente Norme Européenne traite de tous les dangers électriques importants concernant la projection électrostatique des poudres de revêtement, susceptibles de contenir également de faibles quantités de particules métalliques additionnelles, si les travaux sont menés à bien dans des conditions recommandées par le constr

Electrostatic hand-held spraying equipment - Safety requirements - Part 2 : hand-held spraying equipment for ignitable coating powder

DIN EN 1953:2013 涂层材料用喷雾器和喷射器.安全性要求.德文版本EN 1953-2013

Atomising and spraying equipment for coating materials - Safety requirements; German version EN 1953:2013

EN 50050-3:2013 手持式静电喷洒设备 安全要求 第3部分：用于可燃植绒的手持式喷洒设备

1.1 This European Standard specifies the requirements for hand-held or hand-operated electrostatic spraying equipment for ignitable flock within a temperature range from 5 °C to 40 °C to be used in explosive atmospheres generated by their own spray cloud. This European Standard deals with all electrical hazards significant for the electrostatic spraying of flock, which could also contain small quantities of added metal particles, if the work is carried out under conditions recommended by the manufacturer. In particular, this includes ignition hazards resulting from the generated explosive atmosphere. This European Standard specifies the design-related and test requirements for electrostatic spraying equipment of type A-F and type B-F according to Table 1 of EN 50223:2010. 1.2 Electrostatic applicators are considered to be equipment of group II, category 3D for use in potentially explosive areas of zone 22. All other parts of hand-held electrostatic spraying equipment are considered to be equipment of category 3D if they are installed or used in potentially explosive areas of zone 22. NOTE 1 Solvent vapours which could be evaporated by workpieces coated with adhesives do not lead to a zone 2 in the flocking area. 1.3 In addition to the requirements above, the requirements of EN 1953 applies with regard to all other significant hazards relevant for applicators (e.g. health hazards, inadequate ergonomics). 1.4 This European Standard does not apply to  zone classification of the areas in and around spray booths [see EN 50223],  zone classification of other areas with potentially explosive atmosphere [see EN 60079-10-2],  selection, erection and application of other electrical and non-electrical equipment in areas with explosion hazard [see EN 60079 14 and EN 50223],  cleaning of spraying areas, see instruction manual of the spraying equipment,  fire prevention and protection, for instance fire hazards due to other sources [see EN 50223],  explosion protection systems [see EN 50223],  dust hazards [see EN 12981]. NOTE 2 Noise is not considered to be a significant hazard for hand-held spraying equipment for ignitable flock.

Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock

EN 50050-1:2013 静电手持式喷涂设备-安全要求-第1部分：可燃液体涂料的手持式喷涂设备

1.1 This European Standard specifies the requirements for hand-held or hand-operated electrostatic spraying equipment for ignitable liquid coating materials to be used in explosive atmospheres generated by their own spray cloud within a temperature range from 5 °C to 40 °C. This European Standard deals with all hazards significant for the electrostatic spraying of liquid coating materials, which could also contain small quantities of added metal particles, if the work is carried out under conditions recommended by the manufacturer. In particular, this includes ignition hazards resulting from the generated explosive atmosphere. This European Standard specifies the design-related and test requirements for electrostatic spraying equipment of type A-L according to Table 1 of EN 50176:2009. 1.2 With regard to explosion protection and prevention measures, this European Standard also applies to ionisators with high voltage corona charging. Ionisators in conformity with EN 50050-1 provide equipment category 2G. Parts of ionisators, which are intended to be used or installed in Zone 2, provide equipment category 3G in conformity with EN 50050-1, see Annex D. 1.3 Electrostatic applicators are considered to be equipment of group II, category 2G for use in potentially explosive areas of zone 1 or 2, which have been generated by the equipment itself. All other parts of hand-held electrostatic spraying equipment are considered to be equipment of category 3G if they are installed or used in potentially explosive areas of zone 2. 1.4 All other significant hazards relevant for applicators (e.g. ejection of fluids, mechanical strength, electrical hazards (apart from the electrostatic hazards), noise, explosion, contact with or inhalation of dangerous substances, ergonomics) are covered by EN 1953. 1.5 This European Standard also gives details regarding quality assurance systems for electrostatic spraying equipment, see Annex C. 1.6 Additional requirements may be applicable to equipment designed for use in food and pharmaceutical industry. 1.7 This European Standard does not apply to  zone classification of the areas in and around spray booths [see EN 12215],  zone classification of other areas with potentially explosive atmosphere [see EN 60079-10-1],  selection, erection and application of other electrical and non-electrical equipment in areas with explosion hazard [see EN 60079 14 and EN 12215],  cleaning of spraying areas, see instruction manual of the spraying equipment,  fire prevention and protection, for instance fire hazards due to other sources [see EN 12215],  requirements for machinery for the supply and recirculation of coating material under pressure [see EN 12621]. 1.8 When processing coating materials having specific electrical properties (conductivity, resistivity) the function of the hand-held spraying equipment to charge coating materials electrostatically may be affected as a result of a voltage drop at the charging electrode.

Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials

ASTM D7054-04(2013) 用于北美分布的涂漆机的延长杆警示标签标准规范

1.1 This specification covers generally recognized requirements for the cautionary labeling to be placed on extension poles manufactured or sold, or both, for the use with paint preparation and application tools. This specification does not address any other labeling, construction, or safety requirements. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Cautionary Labeling of Extension Poles For Use With Paint Applicators Distributed In North America

NF T35-202*NF EN 1953:2013 镀膜原料的喷雾及喷涂设备.安全性要求

Atomising and spraying equipment for coating materials - Safety requirements

DS/EN 1953:2013 涂料用雾化喷涂设备安全要求

This European Standard deals with all significant hazards, hazardous situations and events which are relevant for both manual and automatic atomising and spraying equipment for application of coating materials on workpieces. In this standard, the term "ma

Atomising and spraying equipment for coating materials - Safety requirements

BS EN 1953:2013 涂装材料雾化和喷涂设备. 安全要求

Atomising and spraying equipment for coating materials. Safety requirements

EN 1953:2013 涂层材料用喷雾器和喷射器的安全性要求

This European Standard deals with all significant hazards, hazardous situations and events which are relevant for both manual and automatic atomising and spraying equipment for application of coating materials on workpieces. In this standard, the term "machine" is used equivalently to "atomising and spraying equipment" and "applicator". Together with this standard, EN 50050, EN 50059, EN 50176, EN 50177 or EN 50348 give requirements for electrostatic applicators. The specific significant risks related to the use of this machinery with foodstuffs and pharmaceutical products are not dealt with in this standard. This standard is only applicable to machinery which is used as intended. It also covers hazards arising from conditions which are reasonably foreseeable by the manufacturer. Applicators can consist of the following parts:- atomising or spraying system; - trigger; - filter; - swivel joint; - safety and control systems; - non-pressurised gravity or siphon feed cup. This European Standard is not applicable to; - applicators designed for operating pneumatic pressure above 15 bar; - non-atomising equipment (e. g. extruding equipment, dispenser); - fluidised bed powder coating machinery; - equipment for the automated application of flock; - spray guns covered by EN 50580; - supply hoses and ducts; - high-pressure cleaner equipped with high pressure water jet machines according to EN 1829-1; - airbrushes for graphic and artistic works; - machinery for the supply and circulation of coating materials under pressure according to EN 12621; - water-jet cutters; - automated devices like robots or reciprocators (EN ISO 10218-1). This standard is not applicable to machinery manufactured before the date of its publication as a European Standard.

Atomising and spraying equipment for coating materials - Safety requirements

NF C23-577/A1*NF EN 50177/A1:2013 可燃性的涂层粉末固定式静电应用设备.安全性要求

Stationary electrostatic application equipment for ignitable coating powders - Safety requirements

DIN EN 50177/A1:2013 可燃性的涂层粉末用固定静电应用装置 安全性要求 德文版本EN 50177-2009/A1-2012

Stationary electrostatic application equipment for ignitable coating powders .Safety requirements; German version EN 50177:2009/A1:2012

DB34/T 1754-2012 滚筒刷

本标准规定了滚筒刷的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以机织物为面料，涂刷各种涂料的滚筒刷。

Roller brush

DS/EN 50177/A1:2012 可燃粉末涂料的固定静电应用设备 安全要求

1.1 This European Standard specifies the requirements for stationary electrostatic application equipment for ignitable coating powders to be used in explosive atmospheres generated by their own spray cloud. A distinction is made between spraying systems c

Stationary electrostatic application equipment for ignitable coating powders - Safety requirements