91.060.20 屋顶 标准查询与下载

ANSI/CRRC 1-2012 CRRC-1标准

CRRC-1 Standard

ANSI/SPRI WD-1-2012 屋顶组件用抗风设计标准规程

Provides a two-part methodology of designing for wind uplift resistance of non-ballasted Built-Up, Modified Bitumen, and Single-Ply roofing system assemblies installed over any type of roof deck.

Wind Design Standard Practice for Roofing Assemblies

ANSI/UL 2218-2012 预制屋面覆盖层材料耐冲击性安全性标准

1. Clarification on preparation of samples for UL 2218 Impact Tests. 2. First time ANSI approval of UL 2218.

Standard for Safety for Impact Resistance of Prepared Roof Covering Materials

ANSI/SPRI/RCI NT-1-2012 核能放射性同位素热化法探测和定位建筑物屋顶系统的潜在潮湿

This standard provides a minimum set of procedures for conducting surveys of moisture in membrane roofing systems, and for analyses of the data obtained in such surveys. Included are operating procedures, operator qualifications, verification, and reporting procedures. It addresses the effect of roof construction, material differences and roof conditions on the numerical data output provided by the nuclear equipment; the limitations in the use of radioisotopic thermalization; and the governmental control of the equipment used to conduct nuclear moisture surveys.

Detection and Location of Latent Moisture in Building Roofing Systems by Nuclear Radioisotopic Thermalization

SNI 7711.1-2012 波纹沥青板 第1部分：产品规格和测试方法

Lembaran Bitumen bergelombang - Bagian 1: Spesifikasi dan metode uji produk

ASTM D7655/D7655M-12(2017) 用作膜屋面系统镇流器的集料尺寸的标准分类

4.1 The wind resistance of ballasted membrane roof systems is determined largely by the size and weight of the ballasted used. ANSI/SPRI RP-4 provides a method for the wind design of ballasted single-ply membrane roof systems and includes specific guidelines for the size and weight of aggregate used as ballast. The aggregate size classifications provided in this standard are intended for use with the guidelines provided ANSI/SPRI RP-4 in designing the wind resistance of aggregate ballasted single-ply membrane roof systems. 4.2 The aggregate size classifications provided in this classification are intended to provide a basis of compliance for contract documents’ that specify certain aggregate sizes for use on ballasted membrane systems. 1.1 This classification defines the aggregate size designations and ranges in mechanical analyses for standard sizes of aggregate used as ballast for membrane roof systems. 1.2 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 With regard to sieve sizes and the size of aggregate as determined by the use of testing sieves, the values in inch-pound units are shown for the convenience of the user; however, the standard sieve designations shown in parentheses is the standard value as stated in Specification E11. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems

SNI 7711.2-2012 波纹沥青板 第2部分：屋顶安装程序

Lembaran Bitumen Bergelombang - Bagian 2: Tata cara pemasangan untuk atap

JG/T 346-2011 合成树脂装饰瓦

本标准规定了合成树脂装饰瓦的术语和定义、分类和标记、材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于工业和民用建筑屋面用合成树脂装饰瓦。

Synthetic resin decorated tile

ASTM A755/A755M-11 室外暴露建筑产品用热浸镀和卷涂预涂金属薄板的标准规范

1.1 This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building products. Sheet of this designation is furnished in coils, cut lengths, and formed cut lengths. Building products include corrugated and various types of roll and brake-formed configurations. 1.2 The substrate is available in several different metallic-coated steel sheet products as enumerated in 4.1, depending on the requirements of the purchaser. 1.3 Coating systems supplied under this specification consist of a primer coat covered by various types and thicknesses of top coats. The combination of primer and top coat is classed as either a two-coat thin-film system or as a two-coat (or more) thick-film system. Typical top-coating materials are: polyester, silicone polyester, acrylic, fluoropolymer, plastisol, or polyurethane. 1.4 This specification is applicable to orders in either inch-pound units (as A755) or SI units [as A755M]. Values in inch-pound units and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of each other. 1.5 Unless the order specifies the “M” designation (SI units) the product shall be furnished to inch-pound units. 1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

GSO EN 1873:2011 屋顶使用的预制配件 塑料屋顶灯 产品技术规格和测试方法

This European Standard specifies requirements for roof lights made of plastic materials (e.g. GF-UP, PC, PMMA, PVC) with and without upstands made of e.g. GF-UP, PVC, steel, aluminium or wood for installation in roofs. These roof lights serve the purpose of lighting by means of daylight and of ventilating interior spaces by means of opening devices. This European Standard applies to roof lights with a rectangular or circular ground plan (see Figures 1 and 2), with an opening span (width) or diameter not larger than 2,5 m and an opening length not larger than 3,0 m in roof pitches up to 25°. This document does not cover roof lights which contribute to the load-bearing or stiffness of the roof itself. This European Standard applies to roof lights without upstand and to roof lights, where a single manufacturer provides all components of the roof light with upstand, which are bought in a single purchase. The possible additional functions of smoke and heat ventilation in case of fire, and/or roof access, are outside the scope of this European Standard. This European Standard does not include calculation with regard to construction, design requirements and installation techniques. NOTE Guidelines for safety, application, use and maintenance of individual roof lights are presented in Annex A.

Prefabricated accessories for roofing - Individual roof lights of plastics - Product specification and test methods

DS/EN 12326-2:2011 不连续屋顶和外包层用板岩和石材 第2部分：板岩和碳酸盐板岩的试验方法

This European Standard specifies test methods for slate and carbonate slate for roofing and wall cladding. It is applicable to natural roofing products as defined in EN 12326-1 used for assembly into discontinuous roofs and external wall cladding.NOTE Where the term """"slate"""" is used in this document it means slate and carbonate slate unless otherwise indicated.

Slate and stone for discontinuous roofing and external cladding - Part 2: Methods of test for slate and carbonate slate

DS/EN 544:2011 带有矿物和/或合成增强材料的沥青瓦 产品规格和测试方法

This European Standard specifies the properties, performance and methods of test of the finished bitumen shingles prior to them being laid on the roof.It also includes rules for marking, labelling and provides a clause for evaluation of conformity.This European Standard does not include design requirements, installation techniques and roof system performance.This European Standard applies to bitumen shingles where the watertightness of the system is ensured by overlapping, by different adhesive systems or a combination of these, according to manufacturer""s installation instructions, intended to be laid as covering for pitched roofs and/or wall cladding.Thi

Bitumen shingles with mineral and/or synthetic reinforcements - Product specification and test methods

DS/EN 1110:2011 防水用柔性板材 屋顶防水用沥青板材 高温下流动阻力的测定

This European Standard specifies the determination of flow resistance of bitumen sheets at elevated temperature. The test is carried out at a specified temperature or consecutively at different temperatures in order to determine the flow resistance limit. Therefore, the test can be used to provide proof of the flow resistance required for a product or to determine the flow resistance limit specific to the product e.g. in order to establish the change in this behaviour as a result of artificial ageing.The test is not applicable to bitumen sheets without reinforcement.

Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of flow resistance at elevated temperature

DS/EN 534+A1/ZA:2011 波纹沥青板 产品规格及试验方法

This European Standard specifies the technical properties and establishes the test and inspection methods for finished corrugated bitumen sheets on leaving the factory. It also provides for the evaluation of conformity of products with the requirements of this standard.

Corrugated bitumen sheets – Product specification and test methods

DS/EN 534+A1:2011 波纹沥青板 产品规格和测试方法

This European Standard specifies the technical properties and establishes the test and inspection methods for finished corrugated bitumen sheets on leaving the factory. It also provides for the evaluation of conformity of products with the requirements of this standard.

Corrugated bitumen sheets - Product specification and test methods

ANSI/ASTM F2021:2011 塑料虹吸式屋面排水系统的设计和安装指南

Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

ASTM E108-11 屋顶覆盖物的防火试验的标准试验方法

The test methods described herein are intended to provide a basis for relative comparison of roof coverings. The test methods include simulated fire exposure to the outside of the roof coverings, and, where applicable, a determination as to whether the fire performance characteristics of the roof coverings will be adversely affected by prolonged exposure to rain. These test methods measure the surface spread of flame and the ability of the roof covering material or system to resist fire penetration from the exterior to the underside of a roof deck under the conditions of exposure. These test methods also provide criteria to determine if the roof covering material will develop flying burning material, identified as flying brands, when subjected to a 12-mph (5.3-m/s) wind during the simulated fire exposure tests. These test methods do not necessarily illustrate the expected performance of roof coverings under all actual fire conditions, but they do provide a basis for comparing roof covering materials when subjected to fire sources that are described herein. These test methods do not provide any basis for determining the fire resistance characteristics when exposed to a fire originating in the building to which the roofing material is applied. The test methods described herein involve calibrating the test equipment using a calibration deck inclined at a slope of 5 in. per horizontal ft (0.416:1). The tests described herein are performed on test decks inclined at slopes up to and including 5 in. per horizontal ft. The severity of the test exposure decreases as the slope of the test deck decreases below 5 in. per horizontal ft.1.1 This fire-test-response standard covers the measurement of the relative fire characteristics of roof coverings under simulated fire originating outside the building. It is applicable to roof coverings intended for installation on either combustible or noncombustible decks when applied as intended for use. The following test methods are included: 1.1.1 Intermittent flame exposure test. 1.1.2 Spread of flame test. 1.1.3 Burning brand test. 1.1.4 Flying brand test. 1.1.5 Rain test. 1.2 Three classes of fire test exposure are described: 1.2.1 Class A Tests are applicable to roof coverings that are effective against severe test exposure, afford a high degree of fire protection to the roof deck, do not slip from position, and do not present a flying brand hazard. 1.2.2 Class B Tests are applicable to roof coverings that are effective against moderate test exposure, afford a moderate degree of fire protection to the roof deck, do not slip from position, and do not present a flying brand hazard. 1.2.3 Class C Tests are applicable to roof coverings that are effective against light test exposure, afford a light degree of fire protection to the roof deck, do not slip from position, and do not present a flying brand hazard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled laboratory conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions. 1.5 This standard does not purpo......

Standard Test Methods for Fire Tests of Roof Coverings

ANSI/GRHC/SPRI VR-1-2011 屋顶绿色系统熔透量阻碍调查程序

This test standard examines the ability of a root protection barrier to prevent root penetration through the waterproofing layer on low-slope (slope

Procedure for Investigating Resistance to Root Penetration on Vegetative Roof Systems

ASTM E455-11 建筑物用框架式地板或屋顶隔膜结构的静负荷试验的标准方法

Framed floor and roof systems are tested by this test method for static shear capacity. This test method will help determine structural diaphragm properties needed for design purposes.1.1 This test method covers procedures designed (1) to evaluate the static shear capacity of a typical segment of a framed diaphragm under simulated loading conditions, and (2) to provide a determination of the stiffness of the construction and its connections. A diaphragm construction is an assembly of materials designed to transmit shear forces in the plane of the construction. 1.2 No effort has been made to specify the test apparatus, as there are a number that can be used as long as the needs of the testing agency are met. If round-robin testing is to be conducted, test apparatus and testing procedures shall be mutually agreed upon in advance by the participants. 1.3 The text of this standard contains notes and footnotes that provide explanatory information and are not requirements of the standard. Notes and footnotes in tables and figures are requirements of this standard. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.

Standard Method for Static Load Testing of Framed Floor or Roof Diaphragm Constructions for Buildings

ANSI/FM 4473-2011 用冰箱冰球撞击测试刚性屋面材料的抗冲击性

This test standard provides a procedure for determining the impact resistance performance of roofing materials. The test uses the impact forces of freezer ice balls propelled to develop free-fall kinetic energies of the same size hail.

Impact Resistance Testing of Rigid Roofing Materials by Impacting with Freezer Ice Balls