91.060.20 屋顶 标准查询与下载

LST EN 612-2005 屋檐排水沟与珠加强正面和雨水管与由金属板制成的接缝

Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet

ASTM D6383-99(2005) EPDM屋顶膜材料制成的粘合接头的失效（蠕变断裂）标准实践

Standard Practice for Time-to-Failure (Creep-Rupture) of Adhesive Joints Fabricated from EPDM Roof Membrane Material

DS/EN 14437:2005 屋顶用粘土或混凝土瓦的抗拔力的测定 屋顶系统试验方法

This document specifies a test method to establish the uplift resistance of installed clay or concrete tiles for roofing, complying with the relevant product standard, EN 490 or EN 1304, which are unfixed or mechanically fixed to the substructure.NOTE The test method has been developed for clay or concrete tiles for roofing but may apply to otherdiscontinuously laid small elements, such as: slates; fibre cement slates; and, stones.The test method is applicable to mechanical fixings such as clips, hooks, screws and nails.In case of mechanically fixed tiles, at least every third tile shall be fixed. The method is not applicable for fixedtiles with fixing patt

Determination of the uplift resistance of installed clay or concrete tiles for roofing - Roof system test method

DIN EN 612:2005 金属薄板制带凸缘加固前端的檐沟和带接缝的雨水管

This document specifies requirements for eaves gutters and rainwater down-pipes made from metal sheet. It establishes the general characteristics, designation system, classification, marking and quality requirements for the products. The standard applies to eaves gutters and external rainwater down-pipes that are supported by metal brackets and used to drain away rainwater. The shape and dimensions of a gutter are defined by the quantity of water to be drained away from the roof to the down-pipes and by architectural design requirements. The ability of the system to handle the water depends upon the design of the roof and the dimensions of the gutter and the down-pipes. The standard specifies the requirements for gutters and rainwater down-pipes which enable these products to meet all usual service conditions such as catching and draining away rainwater, melted snow or ice water from a building to a drainage system or a sewer outside the building.

Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet; German version EN 612:2005

DS/EN 12951:2005 屋顶用预制附件 永久固定屋顶梯子 产品规范和试验方法

This document applies to permanently fixed ladders made of metal which are permanently installed on the load-bearing construction of pitched roofs and which may be stepped or walked on for purposes of inspection, maintenance and repair of equipment installed above the roof surface. This document specifies essential dimensions, materials to be used, requirements with respect to the loadbearing capacity, and the extent of testing. This document does not cover walkways, single treads, single steps or roof ladders that are not permanently fixed nor does it cover fire escape ladders.

Prefabricated accessories for roofing - Permanently fixed roof ladders - Product specification and test methods

DS/EN 607:2005 由 PVC-U 制成的檐槽和配件 定义、要求和测试

This document specifies requirements and test methods of eaves gutters and fittings made from unplasticized poly(vinyl chloride) (PVC-U), and intended to be used for rainwater drainage.

Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing

DS/EN 1462:2005 檐槽支架 要求和测试

This document specifies the requirements for rafter and fascia board brackets intended to support eaves gutters conforming to EN 607 or EN 612.

Brackets for eaves gutters - Requirements and testing

BS EN 612:2005 带凸缘加固前端的檐沟和金属薄板制接缝雨水管

This document specifies requirements for eaves gutters and rainwater down-pipes made from metal sheet. It establishes the general characteristics, designation system, classification, marking and quality requirements for the products. The document applies to eaves gutters and external rainwater down-pipes that are supported by metal brackets and used to drain away rainwater. The shape and dimensions of a gutter are defined by the quantity of water to be drained away from the roof to the down-pipes and by architectural design requirements. The document specifies the requirements for gutters and rainwater down-pipes which enable these products to meet all usual service conditions such as catching and draining away rainwater, melted snow or ice water from a building to a drainage system or a sewer outside the building. Requirements for fixings, supporting construction, flashings or the method of making joints between the different components are not included in this document. This document does not specify requirements for eaves gutters handmade on site.

Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet

JC/T 944-2005 彩喷片状模塑料(SMC)瓦

本标准规定了彩喷片状模塑料(SMC)瓦的分类和标记、技术要求、试验方法、检验规则以及标志、产品合格证、贮存和运输等。 本标准适用于以SMC为原材料，经模压成型的表面喷漆的覆盖屋面用瓦。手糊成型的瓦也可参照执行。

Coloured Sheet Moulding Compound tiles

EN 612:2005 带凸缘加固前端的檐沟和金属薄板制接缝雨水管

This document specifies requirements for eaves gutters and rainwater down-pipes made from metal sheet. It establishesThe general characteristics, designation system, classification, marking and quality requirements forThe products.

Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet

DIN EN 12951:2005 屋顶层用预制附件.长期固定的屋顶梯.产品规范和试验方法

Prefabricated accessories for roofing - Permanently fixed roof ladders - Product specification and test methods; German version EN 12951:2004

BS 8217:2005 屋面用增强沥青膜.实施规范

This British Standard gives recommendations for the selection of reinforced bitumen membranes, their combination to form reinforced bitumen membrane roofing, and their application to flat and sloping roofs. It also gives recommendations for mechanically fastened single-layer reinforced bitumen membranes, torch-applied bitumen membranes, and self-adhesive reinforced bitumen membranes for roofing. The recommendations given for the design, construction and maintenance of new roofs are also applicable to the overlay of existing roofs, subject to confirmation of the suitability of the existing construction. This code of practice does not address or apply to roofs used for special purposes such as car park areas.

Reinforced bitumen membranes for roofing - Code of practice

ANSI/ASME A112.6.9-2005 虹吸式屋顶排水口

Establishes minimum requirements and provides guidelines for the proper design, installation, examination, and testing of siphonic roof drains and siphonic roof drainage piping systems. It includes definitions of terms and parameters involved in the proper design of siphonic drainage systems.

Standard for Siphonic Roof Drainage Systems

EN 1873:2005 屋面用装配附件.塑料单个屋面灯.产品规范和试验方法

This European Standard specifies requirements for roof lights made of plastic materials (e.g. GF-UP, PC,PMMA, PVC) with and without upstands made of e.g. GF-UP, PVC, steel, aluminium or wood for installation inroofs. These roof lights serve the purpose of lighting by means of daylight and of ventilating interior spaces bymeans of opening devices.

Prefabricated accessories for roofing - Individual roof lights of plastics - Product specification and test methods

DIN EN 1462:2004 檐沟撑架.要求和检验

This standard specifies the requirements for rafter and fascia board brackets intended to support eaves gutters conforming to EN 607 or EN 612.

Brackets for eaves gutters - Requirements and testing; German version EN 1462:2004

LST EN 1462-2004 檐槽支架 要求和测试

Brackets for eaves gutters - Requirements and testing

DS/EN 13897:2004 防水用软板 屋面防水用沥青、塑料和橡胶板 低温拉伸后水密性的测定

This document specifies a test for determining the ability of flexible sheets to remain watertight after stretching at low temperature. This standard is applicable for mechanically fastened single layers only.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness after stretching at low temperature

DS/EN 12326-1:2004 用于不连续屋顶和覆层的板岩和石材产品 第1部分：产品规范

This document specifies requirements for slate and stone products for roofing and external cladding, as defined in 3.1, 3.2 and 3.3, used for assembly into discontinuous roofing and external cladding (except bonded cladding). This document does not apply to products for roofing or external cladding made from the following: a) stone other than those defined in 3.1, 3.2 and 3.3; b) concrete; c) polymeric materials; d) fibre reinforced cement; e) metal; f) clay. This document is not applicable to roofing and cladding slates used internally. NOTE 1 Requirements for internal wall lining slate are specified in prEN 1469.

Slate and stone products for discontinuous roofing and cladding - Part 1: Product specification

DS/EN 1297:2004 防水用柔性板 屋顶防水用沥青、塑料和橡胶板 通过长期暴露于紫外线辐射、高温和水的组合进行人工老化的方法

This standard specifies the method for exposure of factory made bitumen or plastic or rubber sheets for roof waterproofing to combined effects of long term exposure by UV radiation, elevated temperature and water as means of artificial ageing.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water

KS F 4752-2004(2009) 出一个金属屋顶形成构件的

Components for metal roof-decks