91.060.20 屋顶 标准查询与下载

IEC 60335-2-83:2001 家用和类似用途电器 安全 第2-83部分：屋顶排放用加热排水沟的特殊要求

Household and similar electrical appliances - Safety - Part 2-83: Particular requirements for heated gullies for roof drainage

ASTM A755/A755M-99 室外暴露建筑产品用热浸镀和卷涂预涂金属薄板的标准规范

1.1 This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building products. Sheet of this designation is furnished in coils, cut lengths, and formed cut lengths. Building products include corrugated and various types of roll and brake-formed configurations. 1.2 The substrate is available in several different metallic-coated steel sheet products as enumerated in , depending on the requirements of the purchaser.1.3 Coating systems supplied under this specification consist of a primer coat covered by various types and thicknesses of top coats. The combination of primer and top coat is classed as either a two-coat thin-film system or as a two-coat (or more) thick-film system. Typical top-coating materials are: polyester, silicone polyester, acrylic, fluoropolymer, plastisol, or polyurethane.1.4 This specification is applicable to orders in either inch-pound units (as A 755) or SI units [as A 755M]. Values in inch-pound units and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of each other.1.5 Unless the order specifies the "M" designation (SI units) the product shall be furnished to inch-pound units. 1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

DS/EN 1931/AC:2001 防水用柔性板材 屋顶防水用沥青、塑料和橡胶板材 水蒸汽传输性能的测定

This Standard specifies a method for the determination of the water vapour transmission properties and for the calculation of the density of moisture flow rate and of the moisture resistance factor (µ) of waterproofing sheets. It is applicable to factory made bitumen, plastic and rubber sheets for waterproofing.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of water vapour transmission properties

DS/EN 13416:2001 防水用柔性板 屋顶防水用沥青、塑料和橡胶板 取样规则

This European Standard specifies the general rules how to select the samples of bitumen, plastic or rubber sheets for roof waterproofing from which the test pieces are taken. It also specifies the conditioning procedures which shall be followed before the test piece is cut from the sample.

Felxible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling

DS/EN 1848-2:2001 防水用柔性板 长度、宽度、直线度和平整度的测定 第2部分：屋顶防水用塑料和橡胶板

This European Standard specifies methods for the determination of length, width, straightness and flatness of plastic and rubber sheets for roof waterproofing supplied in rolls.

Flexible sheets for waterproofing - Determination of length, width, straightness and flatness - Part 2: Plastic and rubber sheets for roof waterproofing

DS/EN 1850-2:2001 防水用软板 可见缺陷的测定 第2部分：屋顶防水用塑料和橡胶板

This European Standard specifies a method for the determination of the visible defects in plastic and rubber sheets for roof waterproofing, which could influence the functional behaviour of these sheets.

Flexible sheets for waterproofing - Determination of visible defects - Part 2: Plastic and rubber sheets for roof waterproofing

SS CP89-2001 金属屋面实施规程

This Code of Practice is intended to provide guidelines, information and recommendations to the specifier and end user on the design, performance, installation, transportation and handling of metal roofing material. It represents a standard of good practice between manufacturers and roofing contractors. It covers the use of galvanised, zinc/aluminium and pre-painted profile metal conforming to SS 370:1994 and other trapezoidal and trough section roof profiles not specifically covered by appropriate standards. It is intended to be read in conjunction with maunfacturer's technical product literature.

CODE OF PRACTICE FOR Metal roofing

LST EN 504-2001 金属板屋顶产品 全支撑铜板屋顶产品规范

Roofing products from metal sheet - Specification for fully supported roofing products of copper sheet

LST EN 502-2001 金属板屋面产品 全支撑不锈钢板屋面产品规范

Roofing products from metal sheet - Specification for fully supported roofing products of stainless steel sheet

LST EN 507-2001 金属板屋面产品 全支撑铝板屋面产品规范

Roofing products from metal sheet - Specification for fully supported roofing products of aluminium sheet

LST EN 505-2001 金属板屋面产品 完全支撑的钢板屋面产品规范

Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet

DS/EN 1107-2:2001 防水用软板 尺寸稳定性的测定 第2部分：屋顶防水用塑料和橡胶板

This European Standard specifies a method for the determination of dimensional variation after heating of plastic and rubber sheets for roof waterproofing.

Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing

DS/EN 12730:2001 防水用柔性板材 屋顶防水用沥青、塑料和橡胶板材 抗静态载荷的测定

This European Standard specifies a test for puncture by static loading for roofing membranes. Mechanical stress on membranes varies from static long-term loads to dynamic short-term loads. This method represents the static category of load where the stress is applied over a period of time.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to static loading

DS/EN 1296:2001 防水用软板 屋顶用沥青、塑料和橡胶板 长期暴露在高温下人工老化的方法

This standard describes the principles, the apparatus and the procedure related to artificial ageing by the use of thermal ageing in a ventilated oven at elevated temperature.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roofing - Method of artificial ageing by long term exposure to elevated temperature

DS/EN 12310-2:2001 防水用软板 抗撕裂强度的测定 第2部分：屋顶防水用塑料和橡胶板

This European Standard specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.

Flexible sheets for waterproofing - Determination of resistance to tearing - Part 2: Plastic and rubber sheets for roof waterproofing

ASTM E2140-01(2009) 通过静水压头测试金属屋顶格间水渗透性的标准试验方法

This test method is a standard procedure for determining water leakage through metal roof panel system sideseams, endlaps, and roof plane penetrations when the roof system is subjected to a specified static water pressure head. Note 28212;In applying the results of tests by this method, note that the performance of a roof or its components or both, is in part a function of proper installation and adjustment. In service, the performance will also depend on the integrity of the supporting construction, roof slope, and on the resistance of components to deterioration by various causes: corrosive atmosphere, aging, ice, vibration, thermal cycling, etc. It is difficult to simulate the identical complex wetting, aging, and other variable conditions that can be encountered in service, including wind-blown ponded water; the effects of temperature and age on sealant performance; differential pressure across the joints due to wind, snow, and ice accumulation; densification and migration; and abrasions within the joint components which may occur during thermal cycling and other weather events. Some joint conditions are more sensitive than others to these factors. This test method will evaluate the resistance of roof panels, sideseams, endlaps, and roof plane penetrations to water submersion. It will not evaluate panel resistance to wind driven rain. Note 38212;See Test Method E1646 for a test which evaluates resistance to wind driven rain. This test method is not a structural adequacy test. This test method is applicable to single skin metal panels, the exterior skin of factory assembled composite panels, and the exterior skin of field assembled composite systems as long as means can be provided to distinguish leakage through the exterior panel sideseams/endlaps and perimeter leakage.1.1 This laboratory test method covers the determination of the resistance to water penetration of exterior metal roof panel system sideseams, endlaps, and roof plane penetrations when a specified static water pressure head is applied to the outside face of the roof panel. Note 18212;This test method is intended to evaluate water-barrier (not water-shedding) roof system joints and details. These systems are also referred to as hydrostatic roof systems. 1.2 This test method is limited to specimens in which the sideseams and attachments are clearly visible and in which the source of leakage is readily observable. 1.3 This test method excludes performance at roof perimeter conditions. 1.4 This test method is suitable for evaluating leakage at roof plane penetrations such as fasteners, curbs, pipes, and expansion joints under a static water pressure head. 1.5 The proper use of this test method requires a knowledge of the principles of water pressure. 1.6 The text of this standard includes notes and footnotes excluding tables and figures, which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific pr......

Standard Test Method for Water Penetration of Metal Roof Panel Systems by Static Water Pressure Head

DS/EN 12200-1:2000 地上外部使用的塑料雨水管道系统 未增塑聚（氯乙烯）（PVC-U） 第1部分：管道、配件和系统规范

This standard specifies the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater downpipes. It also specifies the test parameters for the test methods referred to in this standard. These products are usually used in conjunction with gutters conforming to EN 607. They are not intended for use with products conforming to EN 612. It is applicable to PVC-U rainwater systems of circular, square, rectangular or any other shape with sealed (rubber ring or solvent cement) or unsealed joints. This standard covers a range of pipes and fittings sizes. It also specifies require

Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

LST EN 501-2000 金属板屋顶产品 完全支撑的锌板屋顶产品规范

Roofing products from metal sheet - Specification for fully supported roofing products of zinc sheet

DS/EN 1931:2000 防水用柔性板材 屋顶防水用沥青、塑料和橡胶板材 水蒸汽传输性能的测定

This Standard specifies a method for the determination of the water vapour transmission properties and for the calculation of the density of moisture flow rate and of the moisture resistance factor (µ) of waterproofing sheets. It is applicable to factory made bitumen, plastic and rubber sheets for waterproofing.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of water vapour transmission properties

NP EN 1462-2000 屋内用的供水槽．相关的要求以及测试

A presente Norma especifica os requisitos para suportes cujo objectivo é prender os algerozes suspensos em conformidade com a norma EN 607 ou EN 612.

Brackers for eaves gutters Requirements and testing