91.060.30 天花板、地板、楼梯 标准查询与下载

NF P68-203-1-1:2008 建筑工程.吊顶.第1-1部分:技术模型条款的合同单

Building works - Suspended ceilings - Part 1-1 : contract bill of technical model clauses.

NF P68-203:2008 建筑施工.吊顶.第1-1部分:技术模型条款的合同单.第1-2部分:材料选择的一般标准.第2部分:专用管理模型条款的合同单

Building works - Suspended ceilings - Part 1-1 : contract bill of technical model clauses - Part 1-2 : general criteria for selection of materials - Part 2 : contract bill of special administrative model clauses.

NF P68-203-1-2:2008 建筑施工.吊顶.第1-2部分:材料选择用一般标准

Building works - Suspended ceilings - Part 1-2 : general criteria for selection of materials.

BS 4592-6:2008 工业地板和梯板.玻璃增强塑料(GRP)注模开口网状栅栏和保护栅栏.规范

This part of BS 4592 specifies requirements for the design, manufacture, supply and installation of glass reinforced plastics (GRP) moulded open mesh gratings intended for industrial flooring, walkways and stair treads. It is not applicable where access to machinery is required, in which case the requirements of BS EN ISO 14122 apply. NOTE For the common requirements for industrial flooring and stair treads, see BS 4592-0. In addition to the definitive requirements, this standard also requires the items detailed in BS 4592-0:2006, Clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied.

Industrial type flooring and stair treads - Glass reinforced plastics (GRP) moulded open mesh gratings and protective barriers - Specification

DS/EN 13964/A1:2008 吊顶 要求和测试方法

This European Standard covers membranes, individual substructure components, substructure kits and suspended ceiling kits when these are placed on the market. This European Standard also gives certain specifications for the installed suspended ceiling system, for two reasons: the individual components and kits may have to meet certain requirements in order for the installed system to be able to meet the requirement when the system is installed, and because it is appropriate, for ease of reference, to give both component/kit requirement and installed system requirement in the same document, given the relationship between them.This European Standard provides

Suspended ceilings - Requirements and test methods

DIN 18168-2:2008 天花板内衬和带石膏板的吊顶.第2部分:金属基构件和金属吊杆承载能力的验证

Ceiling linings and suspended ceilings with gypsum plasterboards - Part 2: Verification of the load-carrying capacity of metal sub-constructions and metal suspending rods

JIS A 6507 AMD 1:2008 建筑构件(钢制地板)(修改件1)

Building components (Steel panel for floor) (Amendment 1)

JIS A 6505 AMD 1:2008 建筑构件(混凝土地板)(修改件1)

Building components (Concrete panel for floor) (Amendment 1)

JIS A 6506 AMD 1:2008 建筑构件(木质地板)(修改件1)

Building components (Wood panel for floor) (Amendment 1)

DS/CEN/TS 15680:2008 预制木楼梯 机械试验方法

This Technical Specification gives test methods for prefabricated timber stairs. These stairs are made from timber and/or wood-based materials.The methods included in this document can also be used for single components used in stairs (e.g. steps, handrails, balusters, ...).This document does not consider the overall structure design of these elements. Stairs that are designed to contribute to the overall stability of the works or to the strength of the structure are not covered by this standard.The surfaces of the timber elements may be exposed or covered by finishes.NOTE 1 Where stairs are supplied with a finish or covering, some basic characteristics wil

Prefabricated timber stairs - Mechanical test methods

JC/T 1068-2008 坡屋面用防水材料.自粘聚合物沥青防水垫层

本标准规定了坡屋面用自粘聚合物沥青防水垫层的分类、要求、试验方法、检验规则及标志、包装、运输与贮存等。 本标准适用于坡屋面建筑工程中，各种瓦材及其它屋面材料下面使用的自粘聚合物沥青防水垫层（简称自粘垫层）。

Waterproof materials for pitched roof Underlayments of self adhering polymer modified bituminous

JC/T 1067-2008 坡屋面用防水材料.聚合物改性沥青防水垫层

本标准规定了坡屋面用聚合物改性沥青防水垫层的分类、要求、试验方法、检验规则及标志、包装、运输与贮存等。 本标准适用于坡屋面建筑工程中，各种瓦材及其它屋面材料下面使用的聚合物改性沥青防水垫层（简称改性垫层）。

Waterproof materials for pitched roof Underlayments of polymer modified bituminous

DIN CEN/TS 15680:2008 预制木楼梯.机械试验方法

Prefabricated timber stairs - Mechanical test methods; German version CEN/TS 15680:2007

DD CEN/TS 15680:2007 预制木楼梯.机械试验方法

This Technical Specification gives test methods for prefabricated timber stairs. These stairs are made from timber and/or wood-based materials. The methods included in this document can also be used for single components used in stairs (e.g. steps, handrails, balusters, …). This document does not consider the overall structure design of these elements. Stairs that are designed to contribute to the overall stability of the works or to the strength of the structure are not covered by this standard. The surfaces of the timber elements may be exposed or covered by finishes. NOTE 1 Where stairs are supplied with a finish or covering, some basic characteristics will not be covered by this standard and references should be made to the appropriate product standard (e.g. colour fastness of carpet finishes) NOTE 2 Where the term "stair" is used in this document, it may also apply to individual element or component where appropriate Tests can be carried out on a complete fully assembled system according to manufacturer installation instructions or on individual components. A fully assembled stair test cannot be used to evaluate individual components. There is no particular hierarchy of sequences or the need to carry out all the tests. NOTE The nature of used tests and elements can be given by national regulations.

Prefabricated timber stairs — Mechanical test methods

BS DD CEN/TS 15680:2008 预制木楼梯 机械试验方法

Prefabricated timber stairs. Mechanical test methods

BS 8204-6:2008+A1:2010 整平板,底基和现场铺设用地板材料.合成树脂地板材料.实施规程

This part of BS 8204 gives recommendations for the design and installation of in situ synthetic resin flooring, based on liquid synthetic resin binders in which curing takes place by chemical reaction of the resin components, used internally in buildings. The synthetic resin floorings are bonded to direct finished concrete slabs, polymer-modified cementitious or fine concrete screeds and to existing concrete floors. Annex A gives recommendations for the design and installation of resin terrazzo flooring. Synthetic resin floorings applied to other materials such as timber or metal are not covered by this code of practice. The installation of resilient sports surfacings based on synthetic resins is not covered by this code of practice.

Screeds, bases and in situ floorings. Synthetic resin floorings. Code of practice

BS 8204-6:2008 整平板、底基和现场铺设用地板材料.第6部分:合成树脂地板材料.实施规程

This part of BS 8204 gives recommendations for the design and installation of in situ synthetic resin flooring, based on liquid synthetic resin binders in which curing takes place by chemical reaction of the resin components, used internally in buildings. The synthetic resin floorings are bonded to direct finished concrete slabs, polymer-modified cementitious or fine concrete screeds and to existing concrete floors. Annex A gives recommendations for the design and installation of resin terrazzo flooring. Synthetic resin floorings applied to other materials such as timber or metal are not covered by this code of practice. The installation of resilient sports surfacings based on synthetic resins is not covered by this code of practice.

Screeds, bases and in situ floorings - Part 6: Synthetic resin floorings - Code of practice

BS DD CEN/TS 15680:2007 预制木楼梯.机械试验方法

This Technical Specification gives test methods for prefabricated timber stairs. These stairs are made from timber and/or wood-based materials. The methods included in this document can also be used for single components used in stairs (e.g. steps, handrails, balusters, …). This document does not consider the overall structure design of these elements. Stairs that are designed to contribute to the overall stability of the works or to the strength of the structure are not covered by this standard. The surfaces of the timber elements may be exposed or covered by finishes. NOTE 1 Where stairs are supplied with a finish or covering, some basic characteristics will not be covered by this standard and references should be made to the appropriate product standard (e.g. colour fastness of carpet finishes) NOTE 2 Where the term "stair" is used in this document, it may also apply to individual element or component where appropriate Tests can be carried out on a complete fully assembled system according to manufacturer installation instructions or on individual components. A fully assembled stair test cannot be used to evaluate individual components. There is no particular hierarchy of sequences or the need to carry out all the tests. NOTE The nature of used tests and elements can be given by national regulations.

Prefabricated timber stairs - Mechanical test methods

EN 15644:2008 实心木制传统设计型预制楼梯.规范和要求

This European Standard gives specifications and requirements for prefabricated stairs made of solid wood, i.e. where the components contributing to the fulfilment of mechanical resistance and stability characteristics are made of solid wood. These stairs are traditionally designed. NOTE 1 If the filling of the guarding does not contribute to the mechanical stability and resistance, the used material is not relevant. NOTE 2 Examples of traditionally made/designed stairs are given in Annex E.This European Standard covers: stairs either pre-assembled, partly pre-assembled or in component form including balustrades and handrails for internal or external use.This European Standard does not consider the contribution of these elements to the overall structure design. The ability of a stair to contribute to the overall stability of the works or to the strength of the structure is not covered byThis standard. Carpets on stairs are not covered byThis Standard. The surfaces of the wooden elements may be exposed or covered by finishes. Where stairs are supplied with a finish or covering, aesthetic or visual characteristics will not be covered byThis standard and references shall be made to the appropriate product standard (e. g. colour fastness of carpet finishes).

Traditionally designed prefabricated stairs made of solid wood - Specifications and requirements

ASTM E1264-08e1 吸音顶棚产品的分类

This classification is used to classify and aid in the selection of acoustical ceiling products.1.1 This classification covers ceiling products that provide acoustical performance and interior finish in buildings. Products used in performance spaces and other special applications may require more detailed specification than provided by this classification. 1.2 This classification classifies acoustical ceilings by type, pattern, and certain ratings for acoustical performance, light reflectance, and fire safety. It does not cover the aspects of acoustical ceilings when used as a component of a system or assembly tested for fire endurance or floor/ceiling sound transmission. 1.3 This classification does not include physical properties, such as structural hardness, friability, sag, linear expansion and contraction, and transverse strength, which may affect the handling, installation, and use of acoustical ceiling products (see Test Methods C367). 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Classification for Acoustical Ceiling Products