91.080.20 木结构 标准查询与下载

KS F ISO 9087:2004 木材.轴向负荷下钉子和螺钉固着力的测定

이 규격은 목재의 못 또는 나사못 뽑기 저항 시험 방법에 대하여 규정하며 이 시험 방법

Determination of nail and screw holding power under axial load application for wood

DIN 1052:2004 木结构的设计.总则和建筑物用规则

Design of timber structures - General rules and rules for buildings

ISO 22156:2004 竹子.结构设计

This International Standard applies to the use of bamboo structures, i.e. structures made of bamboo (round bamboo, split bamboo, glued laminated bamboo) or bamboo-based panels joined together with adhesives or mechanical fasteners. This International Standard is based on limit-state design, and on the performance of the structure; see also 7.1. It is only concerned with the requirements for mechanical resistance, serviceability and durability of structures. Other requirements, e.g. concerning thermal or sound insulation, are not considered. Bamboo used as a composite structure may require additional considerations beyond this International Standard. Execution (work on-site, and fabrication of components off-site, and their erection on-site) is covered to the extent that is necessary to indicate the quality of construction materials and products which should be used and the standard of workmanship on-site needed to comply with the assumptions of the design rules.

Bamboo - Structural design

ISO 16670:2003 木结构.机械紧固件接头.准静态逆循环试验方法

This International Standard is intended to provide a cyclic test method as a basis for the derivation of parameters which are required in seismic design of timber structures. The method includes procedures to develop the envelope curves (backbone or skeleton curves; an example is given in Clause A.5.) for joints subjected to a cyclic displacement schedule which produces representative demands imposed on the joints by earthquakes. It does not include criteria for parameters which are, at times, stipulated in national standards or building codes. This standard is intended for joints subjected to lateral load ans is not applicable to joints subjected to withdrawal forces. This International Standard is applicable to joints made with mechanical fasteners used in timber structures loaded under seismic action. NOTE 1 In the context of this Standard, the term "joint" means "connection" in present-day North-American English. NOTE 2 It is recognized that, for some special types of joints, modification of the test method may be necessary provided the test objectives in this clause and the principles in Clause 6 are achieved. See Clause A.2 for details.

Timber structures - Joints made with mechanical fasteners - Quasi-static reversed-cyclic test method

CNS 14749-2003 木质结构用金属扣件

本标准适用于木质构造建筑物所使用下述之木质结构用金属扣件(1)锚定螺栓（Anchor bolt）及螺帽（nut）、垫圈(2)普通螺栓及螺帽、垫圈(3)鱼尾螺栓及螺帽、垫圈(4)带形铁件（扣件）(5)角形铁件（扣件）(6)U形铁件（扣件）(7)蚂蝗钉

Fittings for wooden construction

ASTM D6555-03(2008) 木制反复使用组件的系统效果评定指南

1.1 This guide identifies variables to consider when evaluating repetitive-member assembly performance for parallel framing systems. 1.2 This guide defines terms commonly used to describe interaction mechanisms. 1.3 This guide discusses general approaches to quantifying an assembly adjustment including limitations of methods and materials when evaluating repetitive-member assembly performance. 1.4 This guide does not detail the techniques for modeling or testing repetitive-member assembly performance. 1.5 The analysis and discussion presented in this guideline are based on the assumption that a means exists for distributing applied loads among adjacent, parallel supporting members of the system. 1.6 Evaluation of creep effects is beyond the scope of this guide. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Evaluating System Effects in Repetitive-Member Wood Assemblies

ASTM D6555-03(2014) 木制反复使用组件的系统效果评定的标准指南

1.1 This guide identifies variables to consider when evaluating repetitive-member assembly performance for parallel framing systems. 1.2 This guide defines terms commonly used to describe interaction mechanisms. 1.3 This guide discusses general approaches to quantifying an assembly adjustment including limitations of methods and materials when evaluating repetitive-member assembly performance. 1.4 This guide does not detail the techniques for modeling or testing repetitive-member assembly performance. 1.5 The analysis and discussion presented in this guideline are based on the assumption that a means exists for distributing applied loads among adjacent, parallel supporting members of the system. 1.6 Evaluation of creep effects is beyond the scope of this guide. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Evaluating System Effects in Repetitive-Member Wood Assemblies

SANS 6891:1983 木结构．使用机械紧固件制成的接头．强度和变形特性特定的一般原则

Lays down general principles for the determination of the strength and deformation (slip) characteristics of joints made with mechanical fasteners.

Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics

BS 5268-2:2002 木材在建筑中的使用.第2部分:允许应力设计、材料和工艺的实施规程

BS 5268-2 provides guidance on the structural use of timber, glued laminated timber, plywood and other panel products in load-bearing members. It includes recommendations on quality, grade stresses and modification factors applicable to these materials when used as simple members, or as parts of built-up components, or as parts of structure incorporating other materials. It also gives recommendations for the design of nailed, screwed, bolted, dowelled, connectored and glued joints. In addition, it provides recommendations for a method of test to assess the adequacy of structural assemblies, and it includes general advice on workmanship, various treatments which can be applied, inspection and maintenance. It does not, and it is not intended to, deal comprehensively with all aspects of timber construction. In particular it does not cover well tried and traditional methods of timber construction which have been employed successfully over a long period of time. Compliance with the structural adequacy aspects of the Building Regulations can be achieved by following the recommendations of this standard or via National Technical Approvals Certificates.

Structural use of timber - Code of practice for permissible stress design, materials and workmanship

DS/EN 12512:2002 木结构 试验方法 用机械紧固件制成的接头的循环试验

This standard specifies a test method for determining the ductility, impairment of strength and energy dissipation properties of joints made with mechanical fasteners under cyclic loading.

Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners

GOST 30974-2002 横木和原木的底层木结构建筑物的角接接头.分类,结构和尺寸

Corner joints of wooden low rise buildings of bars and logs. Classification, structures, dimensions

MS 544 Pt.4 Sec.4-2001 木材结构使用规范：第4部分：木板产品：第 4 节：定向刨花板（OSB）

Code of practice for structural use of timber:Part 4:Timber panel products:Section 4:Oriented strand board(OSB)

MS 544 Pt.1-2001 木材结构使用规范：第1部分：总则（第一次修订）

Code of practice for structural use of timber:Part 1:General(First revision)

MS 544 Pt.2-2001 木材结构使用规范：第2部分：实木许用应力设计（第一次修订）

Code of practice for structural use of timber:Part 2:Permissible stress design of solid timber(First revision)

MS 544 Pt.3-2001 木材结构应用规范：第3部分：胶合木的许用应力设计

Code of practice for structural use of timber:Part 3:Permissible stress design of glued laminated timber

MS 544 Pt.4 Sec.1-2001 木材结构使用规范：第4部分：木板产品：第 1 节：结构胶合板

Code of practice for structural use of timber:Part 4:Timber panel products:Section 1:Structrual plywood

MS 544 Pt.4 Sec.2-2001 木材结构使用规范：第4部分：木板产品：第 2 节：船用胶合板

Code of practice for structural use of timber:Part 4:Timber panel products:Section 2:Marine plywood

MS 544 Pt.4 Sec.3-2001 木材结构使用规范：第4部分：木板产品：第 3 节：水泥粘合刨花板（CBP）

Code of practice for structural use of timber:Part 4:Timber panel products:Section 3:Cement bonded particleboard(CBP)

MS 544 Pt.5-2001 木材结构使用规范：第4部分：木板产品：第 5 节：木接缝

Code of practice for structural use of timber:Part 4:Timber panel products:Section 5:Timber joints

MS 544 Pt.6-2001 木材结构使用规范：第6部分：工艺、检验和维护（第一次修订）

Code of practice for structural use of timber:Part 6:Workmanship,inspection and maintenance(First revision)