91.100.15 (Mineral materials and products) 标准查询与下载

ASTM C1527-03 石灰华规格石料的标准规范

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of travertine for general building and structural purposes.1.2 Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.

Standard Specification for Travertine Dimension Stone

ASTM D3018-03 表面有矿物颗粒的A级沥青瓦的标准规范

1.1 This specification covers granule-surfaced asphalt roofing shingles that meet the conditions for Class A fire test, behavior on heating and wind testing of Type I shingles. 1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51mm (2 in.). 1.3 The values stated in acceptable metric units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules

ASTM C216-03 砖石标准规格（由泥土或页岩制成的实心砖石单位）

1.1 This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure.1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section ) of this standard is beyond the scope of this standard.1.3 The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C 902).1.4 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see firing, fired bond, and incipient fusion in Terminology C 43).1.5 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.6 Three types of brick in each of two grades are covered.1.7 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C616-03 石英基规格石料标准规范

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of quartz-based dimension stone for general building and structural purposes. 1.2 Quartz-based dimension stone shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.

Standard Specification for Quartz-Based Dimension Stone

ASTM C544-03(2008) 僵烧镁砂或方镁石颗粒水合作用的标准试验方法

This test method determines relative hydration resistance of magnesia grain. This test method is used in industry to evaluate grain samples and is used for specification purposes in some cases. Care must be taken in interpreting the data. 1.1 This test method covers the measurement of the relative resistance of magnesia grain to hydration. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydration of Dead Burned Magnesite or Periclase Grain

ASTM C544-03(2013) 僵烧镁砂或方镁石颗粒水合作用的标准试验方法

3.1 This test method determines relative hydration resistance of magnesia grain. 3.2 This test method is used in industry to evaluate grain samples and is used for specification purposes in some cases. 3.3 Care must be taken in interpreting the data. 1.1 This test method covers the measurement of the relative resistance of magnesia grain to hydration. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydration of Dead Burned Magnesite or Periclase Grain

ASTM D6928-03 小型德威尔装置中粗集料耐磨细性的标准试验方法

1.1 This method covers a procedure for testing coarse aggregate for resistance to abrasion using the Micro-Deval apparatus.1.2 The values stated in SI units are to be regarded as the standard.1.3 The text of this method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.1.4 This procedure may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus

ASTM D5107-03(2013) 建筑用砂岩表面预清洗的标准实施规程

3.1 Surface cleaning is necessary to prepare architectural sandstone surfaces for application of coatings intended for water repellent protection. Surface cleaning of the sandstone substrate helps to ensure proper adhesion of the coating. 3.2 Use of procedures described in this practice may not be adequate where protective systems will be used for continuous or intermittent immersion or mechanical loading. 1.1 This practice covers non-abrasive surface cleaning of architectural sandstone to remove grease, dirt, loose material, and surface deposits such as soot, fly ash, hydrocarbon residues, and algae and other biological growth in preparation for the application of water repellent coatings. Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning (and detergent water cleaning), and chemical cleaning. 1.2 Limitations—This practice is intended to clean architectural sandstone without damaging it or altering the surface profile. These procedures are not intended for interior stonework. Where work on surfaces of artistic, architectural, cultural, or historic significance is being considered, guidance from specialists should be sought. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 4.

Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone

ASTM D3018-03(2009) 表面有矿物颗粒的A级沥青瓦的标准规范

1.1 This specification covers granule-surfaced asphalt roofing shingles that meet the conditions for Class A fire test, behavior on heating, and wind testing of Type I shingles. 1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules

ASTM C629-03 板条状规格石料标准规范

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of slate for general building and structural purposes.1.2 Dimension slate shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.1.3 It specifically excludes roofing slate (see Specification C 406) and slate for industrial uses.

Standard Specification for Slate Dimension Stone

ASTM C544-03 僵烧镁砂或方镁石颗粒水合作用的标准试验方法

This test method determines relative hydration resistance of magnesia grain. This test method is used in industry to evaluate grain samples and is used for specification purposes in some cases. Care must be taken in interpreting the data. 1.1 This test method covers the measurement of the relative resistance of magnesia grain to hydration.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydration of Dead Burned Magnesite or Periclase Grain

ASTM C1283-03e1 安装粘土烟道内衬的标准实施规程

1.1 This practice covers the minimum requirements for installing clay flue lining for residential concrete or masonry chimneys.1.2 The values stated in inch-pound units are to be regarded as the standard. The values stated in parentheses are for informational purposes only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installing Clay Flue Lining

ASTM C1194-03 建筑铸石抗压强度的标准试验方法

This test method is to be used in determining the compressive strength of cast stone. Compressive strength is one measure of resistance of cast stone to weathering and structural stress.1.1 This test method covers the sampling, preparation of specimens, and determination of the compressive strength of architectural cast stone. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.

Standard Test Method for Compressive Strength of Architectural Cast Stone

ASTM C1088-03 粘土或泥板岩制薄陶面砖的标准规范

1.1 This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. Three types of thin veneer brick units in each of two grades are covered. In this specification, the term thin veneer brick shall be understood to mean clay masonry unit with a maximum thickness of 1 3/4 in. (44.45 mm). Note 18212;Brick intended for paving should be specified under Specification C902. 1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or non-conformance to the property requirements (Section 5) of this standard is beyond the scope of this standard. 1.3 Brick covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of the specification. (See "firing" and "fired bond" in Terminology C43.) 1.4 The values stated in inch-pound units are to be regarded as standard. The metric equivalents may be approximate. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Thin Veneer Brick Units Made From Clay or Shale

ASTM D5106-03 沥青筑路混合物用炼钢炉渣集料标准规范

1.1 This specification covers crushed steel slag coarse and fine aggregates suitable for use in bituminous paving mixtures.1.2 Steel slag coarse and fine aggregates shall be used entirely (Note 0) or combined with other mineral aggregates covered in Specification D 692 or D 1073, to produce paving mixtures as described in Specification D 3515 or D 4215.Note 18212;When 100 % of the coarse aggregate in a bituminous mixture is steel slag, the amount of steel slag fines in that mixture may be limited to prevent bulking.1.3 The values stated in SI units are to be regarded as standard. The values shown in parentheses are for information only.1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Steel Slag Aggregates for Bituminous Paving Mixtures

ASTM C568-03 石灰石规格石料标准规范

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of limestone for general building and structural purposes. 1.2 Dimension limestone shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units of composed fragments, and also crushed and broken stone.

Standard Specification for Limestone Dimension Stone

ASTM C4-02 粘土和多孔粘土排水管的标准规范

1.1 This specification establishes the criteria for acceptance, prior to installation, of drain tile and perforated drain tile to be used for underdrainage, filter fields, leaching fields, and similar subdrainage installations.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the Test Methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Attention is called to Test Methods C 301 and Terminology C 896.

Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile

ASTM C1528-02 外用尺寸石选则的标准指南

1.1 This guide is intended to be used by architects, engineers, specifiers, contractors, and material suppliers who design, select, specify, install, purchase, fabricate, or supply natural stone products for construction applications.1.2 Consensus Standard8212;This guide is an industry consensus standard drafted in a cooperative effort among engineers, architects, geologists, producers, and installers of natural stone.

Standard Guide for Selection of Dimension Stone for Exterior Use

ASTM C778-02 标准砂的标准规范

1.1 This specification covers standard sand for use in the testing of hydraulic cements.1.2 The values stated in SI units are to be regarded as the standard.1.3 Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Standard Sand

ASTM C1405-02 釉面砖标准规范(一次烧成的实心砖)

1.1 This specification covers brick, having a ceramic glaze finish fused to the body during the same process as the unit body firing, that are intended for use in masonry and supplying structural or facing components, or both, to the structure. This specification does not cover double-fired glazed brick. Some double-fired decorative glazes have physical properties which vary from those of single-fired glazes due to the lower temperatures used in applying the decorative coating.1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements of this specification is beyond the scope of this specification. 1.3 Glazed brick are prismatic units available in a variety of sizes, textures, colors, and shapes. Glazed brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see firing, fired bond, glaze, and incipient fusion in Terminology C43).1.4 Glazed brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5 Glazed brick are classified into one of two grades, one of two types, and one of two classes.1.6 Opacity of the glaze is not required unless specified by the purchaser.1.7 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Glazed Brick (Single Fired, Solid Brick Units)