共找到 217 条与 相关的标准,共 15 页
The document describes a method forThe determination of theThermal shock of ceramic tiles.
Ceramic Tiles Part 9: Determination of Resistance to Thermal Shock Supersedes EN 104: 1991
Ceramic Tiles - Part 8: Determination of Linear Thermal Expansion Supersedes EN 103: 1991; ISO 10545-8: 1994
Ceramic Tiles Part 11: Determination of Crazing Resistance for Glazed Tiles Supersedes EN 105: 1991
This part of ISO 10545 specifies a test method for determining the impact resistance of ceramic tiles by measuring the coefficient of restitution.
Ceramic tiles - Part 5: Determination of impact resistance by measurement of coefficient of restitution
This part of ISO 10545 specifies a method for deter-mining the moisture expansion of ceramic tiles.
Ceramic tiles - Part 10: Determination of moisture expansion
Specifies two methods for determining water absorption, apparent porosity, apparent relative density and bulk density of ceramic tiles. Impregnation is obtained by immersion into boiling water or by immersion under vacuum.
Ceramic tiles - Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density
This part of ISO 10545 specifies a method for determining the frost resistance of all ceramic tiles intended for use in freezing conditions in the presence of water.
Ceramic tiles - Part 12: Determination of frost resistance
This part of ISO 10545 specifies a test method for determining the chemical resistance of ceramic tiles at room temperature. The method is applicable to all types of ceramic tiles.
Ceramic tiles - Part 13: Determination of chemical resistance
Specifies rules for batching, sampling, inspection and acceptance/rejection of ceramic tiles.
Ceramic tiles - Part 1: Sampling and basis for acceptance
Describes methods for determining the dimensional characteristics (length, width, thickness, straightness of sides, rectangularity, surface flatness) and the surface quality of ceramic tiles. Spacer lugs, glaze blobs and other irregularities shall be ignored.
Ceramic tiles - Part 2: Determination of dimensions and surface quality
This part of ISO 10545 specifies a method for determining the resistance to stains of the proper surface of ceramic tiles.
Ceramic tiles - Part 14: Determination of resistance to stains
This part of ISO 10545 specifies a test method for determining the resistance to deep abrasion of all unglazed ceramic tiles used for floor coverings.
Ceramic tiles - Part 6: Determination of resistance to deep abrasion for unglazed tiles
This part of ISO 10545 defines a test method for de-termining the coefficient of linear thermal expansion of ceramic tiles. NOTE 1 ISO 13006:—, Ceramic tiles — Definitions, classification, characteristics and marking (to be published), provides property requirements for tiles and other useful information on these products.
Ceramic tiles - Part 8: Determination of linear thermal expansion
This part of ISO 10545 defines a test method for de-termining the crazing resistance of all glazed ceramic tiles except when the crazing is an inherent decorative feature of the product. NOTE 1 ISO 13006:—, Ceramic tiles — Definitions, classification, characteristics and marking (to be published), provides property requirements for tiles and other useful information on these products.
Ceramic tiles - Part 11: Determination of crazing resistance for glazed tiles
Ceramic tiles. Determination of scratch hardness of surface according to mohs.
S'applique aux carreaux d'argile ou d'un mélange d'argile et d'autres matières minérales pour revêtements de sol et de mur, ainsi qu'aux placages de finition, aux carreaux de dallage, de mosaïque et de pierre naturelle.
Ceramic tiles
S'applique aux carreaux d'argile ou d'un mélange d'argile et d'autres matières minérales, cuits à une température supérieure à celle du rouge, pour revêtements de sols et de murs, ainsi qu'aux carreaux non vernissés, aux carreaux de dallage et la mosaïque.
Covering tiles, ceramic
Defines procedures for determination of modulus of rupture and breaking strength. Identical to and reproduced from ISO 10545-4:1994.
Methods of sampling and testing ceramic tiles - Determination of modulus of rupture and breaking strength
Provides information on the properties of ceramic tiles, fixatives and backgrounds, and assists the specifier in the selection of appropriate combinations to meet the requirements of particular installations.
Ceramic tiles - Guide to the selection of a ceramic tiling system
This Standard specifies methods for determining characteristics for adhesives used in the installation of ceramic tiles.
Ceramic tiles - Grouts and adhesives - Test methods for adhesives (ISO 13007-2:2005, MOD)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号