91.100.30 混凝土和混凝土制品 标准查询与下载

22/30444856 DC BS EN 17808 预制混凝土产品 基本特征

BS EN 17808. Precast concrete products. Essential characteristics

ASTM C1202-22e1 混凝土抗氯离子渗透能力电气指示的标准试验方法

1.1 This test method covers the determination of the electrical conductance of concrete to provide a rapid indication of its resistance to the penetration of chloride ions. This test method is applicable to types of concrete where correlations have been established between this test procedure and longterm chloride ponding procedures such as those described in AASHTO T 259. Examples of such correlations are discussed in Refs (1-5).2 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration

ASTM C1202-22 混凝土抗氯离子渗透能力电气指示的标准试验方法

Standard Test Method for Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration

ASTM C469/C469M-22 压缩混凝土静态弹性模量和泊松比的标准试验方法

1.1 This test method covers determination of (1) chord modulus of elasticity (Young’s) and (2) Poisson’s ratio of molded concrete cylinders and diamond-drilled concrete cores when under longitudinal compressive stress. Chord modulus of elasticity and Poisson’s ratio are defined in Terminology E6. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression

DB34/T 569-2022 剪压法检测混凝土抗压强度技术规程

Technical specification for testing the compressive strength of concrete by shear compression method

DB11/T 1959-2022 装配式建筑预制混凝土构件能源消耗限额

Energy Consumption Allowance for Prefabricated Concrete Components of Prefabricated Buildings

JIS A 1135 AMD 1:2022 结构混凝土用轻质粗骨料的颗粒密度和吸水率的试验方法（修改件1）

Methods of test for particle density and water absorption of lightweight coarse aggregates for structural concrete (Amendment 1)

JIS A 1134 AMD 1:2022 结构混凝土用轻骨料颗粒密度和吸水率试验方法（修正件1）

Methods of test for particle density and water absorption of lightweight fine aggregates for structural concrete (Amendment 1)

T/CECS 1040-2022 超高泵送机制砂混凝土应用技术规程

主要内容包括：总则、术语与符号、基本规定、原材料、混凝土拌合物性能、配合比设计、超高泵送方案设计、制备与运输、泵送与浇筑、质量检验与验收等。

Technical specification for the application of ultra-high pumping machine-made sand concrete

T/CECS 1041-2022 超高泵送轻骨料混凝土应用技术规程

主要内容包括总则、 术语和符号、 基本规定、原材料、混凝土拌合物性能、配合比设计与确定、制备与运输、泵送与浇筑、质量检验与验收等。

Application technical specification for ultra-high pumping lightweight aggregate concrete

ASTM C1837-22 用于制造管、箱和预制结构的干铸混凝土生产的标准规范

1.1 This specification covers the production of dry cast concrete as defined in 3.2.1. Requirements for quality of concrete shall be as hereinafter specified. This specification does not cover the placement, consolidation, curing, or protection of the concrete. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures

KS F 4009-2022 预拌混凝土

Ready-mixed concrete

ASTM C78/C78M-22 混凝土弯曲强度的标准试验方法（使用第三点荷载的简支梁）

1.1 This test method covers the determination of the flexural strength of concrete by the use of a simple beam with third-point loading. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)

ASTM C1894-22 混凝土产品微生物引起腐蚀的标准指南

1.1 This guide discusses microbially induced corrosion (MIC) of concrete products and laboratory test methods for determining the resistance of concrete to MIC. Although the guide is intended for concrete products, it also covers cementitious mortar and paste that are used in specialized applications or laboratory investigations. 1.2 While this guide discusses concrete materials and admixtures, the document is not intended to specifically address field exposure conditions or sewage pipe, concrete tank, or concrete riser network design. 1.3 This guide does not cover live trial tests where concrete coupons or other specimens are monitored in sewers. 1.4 This guide does not cover concrete deterioration due to chemical sulfate attack, which is caused by the reaction of sulfate compounds that exist in wastewater with the hydration products of cement. Test methods for assessing sulfate attack are provided by Test Methods C452 and C1012/C1012M. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 The text of this guide references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Microbially Induced Corrosion of Concrete Products

ASTM C140/C140M-22a 混凝土砌块和相关构件取样和试验的标准试验方法

Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units

ASTM C1778-22 降低混凝土中有害碱骨料反应风险的标准指南

1.1 This guide provides guidance on how to address the potential for deleterious alkali aggregate reaction (AAR) in concrete construction. This guide addresses the process of identifying both potentially alkali-silica reactive (ASR) and alkali-carbonate reactive (ACR) aggregates through standardized testing procedures and the selection of mitigation options to minimize the risk of expansion when ASR aggregates are used in concrete construction. Mitigation methods for ASR aggregates are selected using either prescriptive or performance-based alternatives. Preventive measures for ACR aggregates are limited to avoidance of use. Because the potential for deleterious reactions depends not only on the concrete mixture but also the in-service exposure, guidance is provided on the type of structures and exposure environments where AAR may be of concern. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete

T/CAPE 10104-2022 混凝土长期性能和耐久性能试验仪器设备管理规程

前言　 引言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  总则　 4.1  仪器设备管理体系　 4.2　仪器设备管理制度　 4.3　仪器设备报告要求　 4.4　仪器设备人员要求　 4.5　仪器设备数据安全　 4.6　仪器设备能力验证　 4.7　仪器设备检定/校准要求　 4.8　仪器设备报废　 5  基本性能　 5.1  一般规定　 5.2  混凝土抗冻仪性能　 5.3  混凝土动弹性模量测定仪性能　 5.4  混凝土抗水渗仪性能　 5.5  混凝土抗氯离子渗透测定仪性能　 5.6  混凝土收缩测定仪性能　 5.7  混凝土碳化试验箱性能　 5.8  全自动混凝土硫酸盐干湿循环试验箱性能　 5.9  混凝土气体渗透测试仪性能 5.10 混凝土低温硫酸盐试验箱性能　 6  生产要求　 6.1 一般规定　 6.2  抗冻仪生产要求　 6.3  动弹性模量测定仪生产要求 6.4  抗水渗仪生产要求　 6.5  抗氯离子渗透测定仪生产　 6.6  收缩测定仪生产　 6.7  碳化箱生产　 6.8  干湿循环试验箱生产　 6.9  气体渗透测试仪生产　 6.10  低温硫酸盐试验箱生产　 7  使用和维护　 7.1  一般规定　 7.2  抗冻仪的使用和维护　 7.3  动弹性模量测定仪的使用和维护　 7.4  抗水渗仪的使用和维护　 7.5  抗氯离子渗透测定仪的使用和维护　 7.6  收缩测定仪的使用和维护　 7.7　碳化箱的使用和维护　 7.8  干湿循环试验箱的使用和维护　 7.9  气体渗透测试仪的使用和维护　 7.10  低温硫酸盐试验箱的使用和维护　 8  试验仪器设备检定/校准 8.1 一般规定　 8.2  抗冻仪的校准　 8.3  动弹性模量测定仪的校准　 8.4  抗水渗仪校准　 8.5  抗氯离子渗透测定仪的校准　 8.6  收缩测定仪的校准　 8.7  碳化箱的校准　 8.8干湿循环试验箱的校准　 8.9  气体渗透测试仪的校准　 8.10  低温硫酸盐试验箱的校准　 9  辅助材料和物质　 9.1  抗冻仪　 9.2  抗氯离子渗透测定仪　 9.3  气体渗透测试仪 附录A（资料性） 里氏硬度法评价混凝土侵蚀程度　

Regulations for the management of concrete long-term performance and durability testing instruments and equipment

T/SCAS 02-2022 冲击弹性波法检测混凝土结构强度技术规程

本文件规定了冲击弹性波法检测混凝土结构施工质量的基本规定、仪器要求、混凝土结构强度检测及检测报告等。

Technical specification for testing the strength of concrete structures by shock elastic wave method

T/SCAS 03-2022 声振法检测隧道衬砌混凝土质量技术规程

本文件规定了声振法检测隧道衬砌混凝土施工质量检测的基本要求、仪器要求、厚度检测、内部缺陷检测、脱空检测及检测报告等。

Technical specification for testing the quality of tunnel lining concrete by acoustic vibration method

22/30444853 DC BS EN 13369.预制混凝土产品的通用规则

BS EN 13369. Common rules for precast concrete products